E36 润滑脂 标准查询与下载

ASTM D1743-05ae1 测定润滑脂防腐蚀特性的试验方法

This test method differentiates the relative corrosion-preventive capabilities of lubricating greases under the conditions of the test.1.1 This test method covers the determination of the corrosion preventive properties of greases using grease-lubricated tapered roller bearings stored under wet conditions. This test method is based on CRC Technique L 41178; that shows correlations between laboratory results and service for grease lubricated aircraft wheel bearings.1.2 Apparatus Dimensions8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 All Other Values8212;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases

ASTM D1743-05a 测定润滑脂防腐蚀特性的试验方法

1.1 This test method covers the determination of the corrosion preventive properties of greases using grease-lubricated tapered roller bearings stored under wet conditions. This test method is based on CRC Technique L 41 that shows correlations between laboratory results and service for grease lubricated aircraft wheel bearings.1.2 Apparatus Dimensions8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard./p>1.3 All Other Values8212;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases

NF T60-171*NF ISO 13737:2004 石油产品和润滑剂.低温下润滑脂针入度的测定

Petroleum products and lubricants - Determination of low-temperature cone penetration of lubricating greases.

ANSI/ASTM D7066:2004 用红外测定法测定三氟氯乙烯(s-316)可回收石油和润滑脂及非极性材料的二聚物/三聚物的试验方法

This test method covers the determination of oil and grease and nonpolar material in water and wastewater by an infrared (IR) determination of dimer/trimer of chlorotrifluoroethylene (S-316) extractable substances from an acidified sample. Included in this estimation of oil and grease are any other compounds soluble in the solvent. The method is applicable to measurement of the light fuel although loss of some light ends during extraction can be expected. This method defines oil and grease in water and wastewater as that which is extractable in the test method and measured by IR absorption at 2930 cm- or 3.4 microns. Similarly, this test method defines nonpolar material in water and wastewater as that oil and grease which is not adsorbed by silica gel in the test method and measured by IR absorption at 2930 cm-. This method covers the range of 5 to 100 mg/L and may be extended to a lower or higher level by extraction of a larger or smaller sample volume collected separately. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine (D 3856 Guide for Good Laboratory Practices) the applicability of regulatory limitations prior to use.

Test Method for Dimer/Trimer of Chlorotrifluoroethylene (s-316) Recoverable Oil and Grease and Nonpolar Material by Infrared Determination

DIN 51825:2004 润滑剂.润滑脂K.分类和要求

In this standard the classification of and specifications for lubricating greases, NGLI-classes 1 to 4 according to DIN 51818, and test methods are established.

Lubricants - Lubricating greases K - Classification and requirements

SH/T 0109-2004 润滑脂抗水淋性能测定法

Petroleum products and lubricants--Determination of water washout characteristics of lubricating greases

KS M ISO 2176:2003 石油产品.润滑脂.滴点的测定

이 규격은 그리스의 적점을 측정하는 방법에 대하여 규정한다.비 고 1. 적점 시험

Petroleum products－Lubricating grease－Determination of dropping point

JIS K 2220:2003 润滑脂

この規格は，主として各種機械部品の潤滑剤として用いるグリース(ギヤコンパウンドを含む)について規定する。

Lubricating grease

ASTM D1264-03(2008) 确定润滑脂抗水洗特性的标准试验方法

This test method estimates the resistance of greases to water washout from ball bearings under conditions of the test. No correlation with field service has been established.1.1 This test method covers the evaluation of the resistance of a lubricating grease to washout by water from a bearing, when tested at 38 and 79°C (100 and 175°F) under the prescribed laboratory conditions. It is not to be considered the equivalent of service evaluation tests. This test method may not be suitable for some greases containing highly volatile components. 1.2 The values state in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 6.3.

Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases

ASTM D4289-03 润滑脂及润滑液与弹性材料的配伍性的标准试验方法

1.1 This test method evaluates the compatibility of lubricating greases and fluids with coupons cut from standard elastomer sheets (Practice D 3182) or, optionally, from SAE Specification AMS 3217/2B (NBR-L) and AMS 3217/3A (CR) sheets. Compatibility is evaluated by determining the changes in volume and Durometer A hardness that occur when elastomer coupons are totally immersed in a lubricant sample for 70 h at either 100 or 150176;C or as required by the lubricant specification.1.1.1 Some lubricant specifications may require different test conditions, such as longer durations or lower or higher temperatures. In such instances, the repeatability and reproducibility values stated in Section 12 do not apply, and the user and supplier should agree on acceptable limits of precision.Note 18212;The scope of this test method now includes the evaluation of the elastomer compatibility of both lubricating fluids and greases. Testing of fluids was not included in Test Method D 4289-95 and earlier versions.1.2 This test method can also be used as a guide to evaluate the compatibility of greases with rubber products not in standard sheet form (Practice D 3183).1.3 The values stated in SI and Durometer A units shall be regarded as the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 8.4-8.6.

Standard Test Method for Elastomer Compatibility of Lubricating Greases and Fluids

ASTM D2509-03(2008) 润滑脂负载能力的标准试验方法(泰姆肯法)

The test method is used widely for specification purposes and is used to differentiate between greases having low, medium, or high levels of extreme pressure characteristics. The results may not correlate with results from service.1.1 This test method covers the determination of the load-carrying capacity of lubricating greases by means of the Timken Extreme Pressure Tester. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 7.1, 7.2, and 9.4.

Standard Test Method for Measurement of Load-Carrying Capacity of Lubricating Grease (Timken Method)

ASTM D1264-03e1 确定润滑脂抗水洗特性的标准试验方法

This test method estimates the resistance of greases to water washout from ball bearings under conditions of the test. No correlation with field service has been established.1.1 This test method covers the evaluation of the resistance of a lubricating grease to washout by water from a bearing, when tested at 38 and 79176;C (100 and 175176;F) under the prescribed laboratory conditions. It is not to be considered the equivalent of service evaluation tests. This test method may not be suitable for some greases containing highly volatile components.1.2 The values state in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 6.3.

Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases

ASTM D1264-03 确定润滑脂抗水洗特性的标准试验方法

1.1 This test method covers the evaluation of the resistance of a lubricating grease to washout by water from a bearing, when tested at 38 and 79176;C (100 and 175176;F) under the prescribed laboratory conditions. It is not to be considered the equivalent of service evaluation tests. This test method may not be suitable for some greases containing highly volatile components.1.2 The values state in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 6.3.

Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases

ASTM D4289-03(2008) 润滑脂及润滑液弹性体相容性的标准试验方法

Measurement of the changes in the volume and hardness of an elastomer that occur from immersion in a lubricating grease or fluid provides a means for evaluating relative compatibility. Much of this test method was derived from procedures described in Test Method D 471 and Federal Test Method 791C/3603.5. In contrast to these two test methods, which emphasize the evaluation of rubber and rubber-like compounds, Test Method D 4289 was developed specifically to evaluate lubricating greases and fluids, especially those used in automotive applications, although the test method can be applied to lubricants used in industrial applications as well. Excepting the Shore Durometer A, this test method requires no specialized, rubber-testing equipment. Virtually all other equipment and supplies specified in the procedure are stock items in lubricants laboratories. The volume and hardness-change values determined by this test method do not duplicate similar changes that occur in elastomeric seals under actual service conditions. However, they can be correlated in many instances. In one such instance, the volume-change values determined by the antecedent of this test method correlated (r 2 = 0.99) with those that occurred during a vehicle test. Because of wide variations in service conditions and differences in grease and elastomer formulations, correlations between the results obtained with this test method and particular applications should be determined on an individual basis. When the optional Reference Elastomers AMS 3217/2B (acrylonitrile-butadiene, NBR-L) and AMS 3217/3A (chloroprene, CR) are used to evaluate compatibility, the results can be used to judge a service characteristic of lubricants. In this respect, this test method is useful for lubricant specifications (for example, Specification D 4950). Similarly, this test method can be used in specifications for lubricating fluids as well. With specifications requiring elastomers other than Reference Elastomers AMS 3217/2B or AMS 3217/3A, coupons cut from standard sheets (Practice D 3182) should be used. When the preparation of such coupons is not feasible, or the lubricant specification requires the use of rubber products that do not have a suitable size or configuration for use in preparing coupons for testing (Practice D 3183), this test method can be used as a guide for evaluating compatibility. Note 48212;Inasmuch as the precision values apply only to the elastomers specified in Annex A1 of Test Method D 4289, when a lubricant specification requires some other elastomer, the user and supplier of the lubricant should agree to the values of acceptable precision. Such values may or may not be the same as those of Test Method D 4289. It is recommended that the agreed upon precision values be stated in the user''s lubricant specification. The results of this test method are most applicable to the use of lubricating greases and fluids in contact with elastomeric seals, boots, O-rings, and similar products, where the physical demands on the elastomer are not extreme. In critical applications where the lubricant will be in contact with rubber parts subject to severe flexing, extreme temperatures, or similar stresses, other rubber properties, such as tensile strength and elongation, should also be evaluated as they may be more indicative of the true compatibility characteristics.1.1 This test method evaluates the compatibility of lubricating greases and fluids with coupons cut from standard elastomer sheets (Practice D 3182) or, optionally, from SAE Specification AMS 3217/2B (NBR-L) and AMS 3217/3A (CR) sheets. Compatibility is evaluated by determining the......

Standard Test Method for Elastomer Compatibility of Lubricating Greases and Fluids

SH/T 0716-2002 润滑脂抗微动磨损性能测定法

Test method for fretting wear protection by lubricating greases

SH/T 0721-2002 润滑脂摩擦磨损性能测定法(高频线性振动试验机法)

Standard test method for measuring friction and wear properties of lubricating grease using a high-frequency, linear-oscillation (SRV) test machine

ASTM D4290-02 在加速条件下测定汽车轮轴承润滑脂渗漏倾向的标准试验方法

1.1 This test method covers a laboratory procedure for evaluating leakage tendencies of wheel bearing greases when tested under prescribed conditions.1.2 The values stated in SI units, except apparatus dimensions, are to be regarded as the standard. Apparatus dimensions in inches are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 8.1-8.4.

Standard Test Method for Determining the Leakage Tendencies of Automotive Wheel Bearing Grease Under Accelerated Conditions

ASTM D5483-02e1 用压差扫描热量测定法测试润滑脂的氧化反应时间的标准试验方法

1.1 This test method covers the determination of oxidation induction time of lubricating greases subjected to oxygen at 3.5 MPa (500 psig) and temperatures between 155 and 210176;C.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Oxidation Induction Time of Lubricating Greases by Pressure Differential Scanning Calorimetry

ASTM D1403-02 用1/4和1/2标度锥形设备测定润滑脂锥入度的标准试验方法

These test methods are applicable to greases of National Lubricating Grease Institute (NLGI) consistency numbers 0 to 4 and is intended for use only where the size of the sample prevents the use of Test Methods D 217. Actual reduced-scale penetration values are not used or reported. They are converted to full-scale penetration values (see Sections 9 and 10). This test method is not intended to replace the full-scale penetration as described in Test Methods D 217. Precision is better in the full-scale penetration method. Worked penetration results, after conversion to full-scale values, may be used to establish the consistency of lubricating greases within the above NLGI consistency numbers. The results obtained from these test methods are widely used for specification purposes, however, no correlation with field performance has been established. Unworked penetration results provide a means of evaluating the effect of storage conditions on grease consistency.1.1 These test methods cover two procedures for measuring the consistency of small samples of lubricating greases by penetration of a 1/4-scale cone or a 1/2-scale cone. These test methods include procedures for the measurement of unworked and worked penetrations.1.2 Unworked penetrations do not generally represent the consistency of greases in use as effectively as do worked penetrations. The latter are usually preferred for inspecting lubricating greases.1.3 The values in SI units are to be regarded as the standard. The values given in parentheses are for information only. In the United States, the equipment dimensions stated in inches are to be regarded as the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Cone Penetration of Lubricating Grease Using One-Quarter and One-Half Scale Cone Equipment

ASTM D942-02(2007) 氧弹法测定润滑脂氧化稳定性的标准试验方法

This test method measures the net change in pressure resulting from consumption of oxygen by oxidation and gain in pressure due to formation of volatile oxidation by-products. This test method may be used for quality control to indicate batch-to-batch uniformity. It predicts neither the stability of greases under dynamic service conditions, nor the stability of greases stored in containers for long periods, nor the stability of films of greases on bearings and motor-parts. It should not be used to estimate the relative oxidation resistance of different grease types.1.1 This test method determines resistance of lubricating greases to oxidation when stored statically in an oxygen atmosphere in a sealed system at an elevated temperature under conditions of test.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements see Sections 6 and 7.

Standard Test Method for Oxidation Stability of Lubricating Greases by the Oxygen Pressure Vessel Method