E36 润滑脂 标准查询与下载

ASTM D7527-10 线性扫描伏安法测定润滑脂中的抗氧化剂含量的标准试验方法

The quantitative determination of antioxidants in new greases measures the amount of the chemical compounds that were added to the base oil as protection against grease oxidation. For in-service oil greases, the voltammetric test method measures the amount of original (individual) antioxidants remaining after grease oxidation have reduced its concentration. Before making final judgment on the remaining useful life of the in-service grease, which might result in the replacement of the grease reservoir, it is advised to perform additional analytical techniques, such as Test Method D942 and D5483, which may be used to measure the remaining oxidative life of the used grease. 4.1.1 This test method is applicable to mineral oil-based and synthetic oil-based greases, based on all type of applied thickeners. This test method is applicable to greases containing at least one type of antioxidant. The presence of other types of additives like corrosion inhibitors or metal deactivators will not interfere with this test method.1.1 This test method covers the voltammetric determination of antioxidants in new or in-service lubricating greases in concentrations from 0.0075 weight percent up to concentrations found in new greases by measuring the amount of current flow at a specified voltage in the produced voltammogram. 1.2 This test method is intended to monitor the antioxidant content in lubricating greases; it cannot be applied for lubricating greases that do not contain antioxidants. 1.3 This test method is designed to allow the user to monitor the antioxidant depletion rate of in-service greases through its life cycle as part of condition monitoring programs. This test method is performed in order to collect and trend early signs of deteriorating lubricant grease, and it may be used as a guide for the direction of any required maintenance activities. This will ensure a safe, reliable, and cost-effective operation of the monitored plant equipment. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measurement of Antioxidant Content in Lubricating Greases by Linear Sweep Voltammetry

ASTM D2596-10 润滑脂的极端压力特性测定的标准试验方法(四球法)

This test method, used for specification purposes, differentiates between lubricating greases having low, medium, and high level of extreme-pressure properties. The results do not necessarily correlate with results from service. It is noted that lubricating greases that have as their fluid component a silicone, halogenated silicone, or a mixture comprising silicone fluid and petroleum oil, are not applicable to this method of test. 1.1 This test method covers the determination of the load-carrying properties of lubricating greases. Two determinations are made: 1.1.1 Load-Wear Index (formerly called Mean-Hertz Load), and 1.1.2 Weld Point, by means of the Four-Ball Extreme-Pressure (EP) Tester. 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method)

ASTM D2596-10e1 测量润滑脂极压性能40;四球法41;的标准试验方法

5.1 This test method, used for specification purposes, differentiates between lubricating greases having low, medium, and high level of extreme-pressure properties. The results do not necessarily correlate with results from service.3 5.2 It is noted that lubricating greases that have as their fluid component a silicone, halogenated silicone, or a mixture comprising silicone fluid and petroleum oil, are not applicable to this method of test. 1.1 This test method covers the determination of the load-carrying properties of lubricating greases. Two determinations are made: 1.1.1 Load-Wear Index (formerly called Mean-Hertz Load), and 1.1.2 Weld Point, by means of the Four-Ball Extreme-Pressure (EP) Tester. 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease 40;Four-Ball Method41;

BS EN 14865-1:2009+A1:2010 轨道交通.轴箱润滑脂.润滑能力的测试方法

Railway applications. Axlebox lubricating greases. Method to test the ability to lubricate

BS EN 14865-1:2009 轨道交通.轴箱润滑脂.润滑能力的测试方法

Railway applications - Axlebox lubricating greases - Method to test the ability to lubricate

SAE AMS3055B-2009 粘度为15的石油基仪器轴承润滑油

1.1 FormThis specification covers the requirements for a refined paraffinic petroleum-base lubricant.1.2 ApplicationThis lubricant has been used typically in spin axis bearings of gyroscopes, accelerometers, andsimilar bearing applications, but usage is not limited to such applications.1.3 Safety- Hazardous MaterialsWhile the materials, methods, applications, and processes described or referenced in thisspecification may involve the use of hazardous materials, this specification does not addressthe hazards which may be involved in such use. It is the sole responsibility of the user to ensurefamiliarity with the safe and proper use of any hazardous materials and to take necessaryprecautionary -measures to ensure the health and safety of all personnel involved.1.3.1 Precaution: The lubricant contains tricresyl phosphate which will cause paralysis if ingested. Do not use this lubricant in or on equipment which may contact food or other product which is taken internally.

Petroleum Base Instrument Bearing Lubricant Viscosity 15

GJB 6745-2009 舰船齿形联轴器润滑脂规范

本规范规定了舰船齿形联轴器润滑脂的要求。

Specification for naval rowned tooth gear coupling grease

ASTM D4425-09 离心法从润滑脂中分离油的标准试验方法(科佩斯法)

This test method is useful in evaluating the degree to which a grease would separate into fluid and solid components when subjected to high centrifugal forces. Flexible shaft couplings, universal joints, and rolling element thrust bearings are examples of machinery which subject lubricating greases to large and prolonged centrifugal forces. This test method has been found to give results that correlate well with results from actual service. The test method may be run at other conditions with agreement between parties but the precision noted in this test method will no longer apply. 1.1 This test method covers a procedure for determining the tendency of lubricating grease to separate oil when subjected to high centrifugal forces. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Oil Separation From Lubricating Grease by Centrifuging (Koppers Method)

GJB 2661A-2008 飞机宽温度通用润滑脂规范

本规范规定了飞机宽温度通用润滑脂的要求。

Specification for aircraft grease of general purpose and wide temperature range

SANS 3448:2008 工业液体润滑剂.ISO粘度分类

Establishes a system of viscosity classification for industrial liquid lubricants and related fluids.

Industrial liquid lubricants - ISO viscosity classification

SH/T 0428-2008 高温下润滑脂在球轴承中的寿命测定法

1.1本标准规定了评定润滑脂在高温、高转速及轻负荷运转的球轴承中的性能的试验方法。 1.2本标准采用国际单位制（SI）单位。 1.3本标准未示明与其使用有关的所有安全问题，因此用户在使用本标准前应建立适当的安全和防护措施并确定有适用性的管理制度。

Standard test method for life of lubricating greases in ball bearings at elevanted temperatures

NF T60-132:2008 石油产品和润滑剂.润滑脂和石油脂的锥形针入度的测定

Petroleum products and lubricants - Determination of cone penetration of lubricating greases and petrolatum.

SANS 1851:2008 润滑脂

Covers the perfomance requirements of four classes of lubricating grease, namely industrial non-extreme pressure, industrial high perfomance extreme pressure, automotive non-extreme pressure, and automotive and multi-purpose extreme pressure, each in fou

Lubricating grease

BS EN 12081:2007+A1:2010 轨道交通.轴套.润滑脂

Railway applications. Axleboxes. Lubricating greases

BS EN 12081:2007 轨道交通.轴套.润滑脂

This European Standard specifies the quality requirements of greases intended for the lubrication of axlebox rolling bearings according to EN 12080, required for reliable operation of trains on European networks. It covers the approval procedure, the method of quality control and quality monitoring of the grease. The grease requirements are given for two speed classes.

Railway applications - Axleboxes - Lubricating greases

ASTM D7421-08 使用高频线性振荡(SRV)试验机测定润滑脂极端压力特性的标准试验方法

This laboratory test method can be used to quickly determine extreme pressure properties of lubricating oils at selected temperatures specified for use in applications where not only high-speed vibrational or start-stop motions are present with high Hertzian point contact. This test method has found wide application in qualifying lubricating oils used in constant velocity joints of front-wheel-drive automobiles, gear-hydraulic circuit, rear axles, gears and engine components. Users of this test method should determine whether results correlate with field performance or other applications.1.1 This test method covers a procedure for determining extreme pressure properties of lubricating oils for hydraulics, gears and engines under high-frequency linear-oscillation motion using the SRV test machine. Note 18212;This test method was developed and the international round robin tests were jointly performed with the DIN 51834 working group. This procedure is based on the 2005 revision of Test Method D 5706 for greases and differs regarding the stroke length and the cleaning solvent. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining Extreme Pressure Properties of Lubricating Oils Using High-Frequency, Linear-Oscillation (SRV) Test Machine

ASTM D5969-08 标准润滑脂防腐性能的预防性标准试验方法中存在的稀释合成海水环境

This test method differentiates the relative corrosion-preventive capabilities of lubricating greases under the test conditions.1.1 This test method covers the determination of the corrosion-preventive properties of greases using grease-lubricated tapered roller bearings exposed to various concentrations of dilute synthetic sea water stored under wet conditions. It is based on Test Method D 1743, which is practiced using a similar procedure and distilled water. The reported result is a pass or fail rating as determined by at least two of three bearings. 1.2 Apparatus Dimensions8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 All Other Values8212;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Corrosion-Preventive Properties of Lubricating Greases in Presence of Dilute Synthetic Sea Water Environments

DIN 21258:2007 采矿用摩擦提升钢索的润滑剂和浸渍剂.安全要求和测试

Lubricants and impregnating compounds for friction hoist ropes in mining - Safety requirements and testing

GJB 6101-2007 7258润滑脂规范

本规范规定了7258润滑脂的要求。

Specification for 7258 grease

SH/T 0789-2007 极压聚脲润滑脂

本标准规定了极压聚脲润滑脂的要求和试验方法、检验规则及标志、包装、运输和贮存。 本标准所属产品适用于冶金行业钢厂热连铸机集中润滑系统及其他处于高温、高负荷、水淋条件下工作设备的润滑与防护。

Extreme pressure polpzea lubricating grease