G43 橡胶密封件 标准查询与下载

HG/T 2701~2702-2016 压缩式封隔器和扩张式封隔器胶筒（2016）

Compression Packer and Expansion Packer Cartridges (2016)

HG/T 2702-2016 扩张式封隔器胶筒

Expansion packer rubber barrel

GOST 33785-2016 密封材料和密封材料垫片. 耐液体性的测定方法

Sealing materials and gaskets from them. Method for determination of resistance to liquids

GOST 33784-2016 密封材料和密封材料垫片. 可压缩性和可恢复性的测定方法

Sealing materials and gaskets from them. Method for determination of compressibility and recoverability

HG/T 4785-2014 车用空气滤清器橡胶密封件

本标准规定了车用空气滤清器橡胶密封件的分类、符号、结构及标识，要求，检验规则，标志、包装、运输和贮存。 本标准适用于汽车空气滤清器橡胶密封件(以下简称密封件)。

Rubber seals for air cleaner of automobile

HG/T 2021-2014 耐高温润滑油O形橡胶密封圈

本标准规定了耐高温润滑油O形橡胶密封圈的要求，试样，检验规则，标志、包装、运输和贮存。 本标准适用于耐高温润滑油用O形橡胶密封圈。

O-rings resistant to high temperature and oil

SAE AIR1707B-2014 O型密封圈失效型式

The information presented herein describes the commonly observed patterns of O-ring failure by means of both text and illustration. Possible causes and corrective actions are indicated for alleviating the problem.

Patterns of O-ring Failures

HG/T 4624-2014 汽车滑销防尘密封保护套

本标准规定了汽车滑销防尘密封保护套(以下简称保护套)的要求、检验规则及标志、包装、运输和贮存。本标准适用于载重汽车的制动盘之间的滑销防尘密封保护套。

Anti-dust sealing protective sleeve of vehicle sliding pin

HG/T 4623-2014 船用货舱盖橡胶密封带

本标准规定了船舶货舱盖橡胶密封带(以下简称密封带)的要求、密封带试验方法、检验规则、标志、包装、贮存。本标准适用于货船大舱口盖用密封带。

Sealing rubber for hatch covers of cargo ship

HG/T 4622-2014 耐二甲醚橡胶密封材料

本标准规定了耐二甲醚橡胶密封材料的要求、检验规则、标志、包装、运输、贮存等。本标准适用于耐二甲醚的橡胶密封材料,也适用于耐液化石油气二甲醚混合液的橡胶密封材料。

Rubber compounds for seals used for dimethyl ether

ASTM C564-14 铸铁污水管及其配件用橡胶垫圈的标准规范

1.1 This specification covers preformed rubber gaskets used to seal joints in cast iron soil pipe and fittings. 1.2 The committee with jurisdiction over this standard is not aware of another comparable standard for materials covered in this standard. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following safety hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings

ASTM C1016-14 密封剂<丁二烯橡胶>(填缝料)吸水率的测定的标准试验方法

5.1 This test method determines the amount of water absorbed by a backing material. Water absorption by the backing may affect sealant performance. 5.2 This test method is also useful when designating proper storage of back up material and in determining appropriate precautions when using backing materials. 5.3 The specifier, using this test method, can exercise judgment in the selection of backing materials based on water absorption characteristics. 1.1 This test method covers a laboratory procedure for determining the water absorption characteristics of sealant backing and joint filler materials, hereinafter referred to as backing. 1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units in parentheses are for information only. 1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other ASTM committees or other organizations. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Water Absorption of Sealant Backing 40;Joint Filler41; Material

JB/T 9669-2013 避雷器用橡胶密封件及材料规范

本标准规定了避雷器用橡胶密封件的结构型式、材料规范、试验方法和检验规则等内容。本标准适用于避雷器用橡胶密封件。

Specification for rubber sealing gaskets and meterials for surge arresters

JIS B 2401-2 ERRATUM 1:2013 勘误表

ERRATUM

DIN 7863-2:2013 用于窗户和包层的弹性体玻璃和面板垫片.技术交货条件.第2部分:有孔弹性体玻璃和面板垫片

Elastomer glazing and panel gaskets for windows and claddings - Technical delivery conditions - Part 2: Celluar elastomer glazing and panel gaskets

BS ISO 5892:2013 建筑橡胶衬垫.预成型密实的硫化结构衬垫材料.规格

Rubber building gaskets. Materials for preformed solid vulcanized structural gaskets. Specification

JIS B 2402-5:2013 组合弹性密封元件的旋转轴唇型密封件.第5部分:外观不完整性的鉴定

This Standard defines and classifies visual surface imperfections (hereafter referred to as “imperfections”) of rotary shaft lip-type seals incorporating elastomeric sealing elements (hereafter referred to as “seals”).

Rotary shaft lip-type seals incorporating elastomeric sealing elements.Part 5: Identification of visual imperfections

JIS B 2402-3:2013 组合弹性密封元件的旋转轴唇型密封件.第3部分:储存、运输和安装

This Standard specifies the storage, handling and installation of rotary shaft lip-type seals (hereafter referred to as “seals”).

Rotary shaft lip-type seals incorporating elastomeric sealing elements.Part 3: Storage, handling and installation

JIS B 2402-1:2013 组合弹性密封元件的旋转轴唇型密封件.第1部分:标称尺寸和公差

This Standard specifies nominal dimensions and tolerances of the rotary shaft lip-type seals with spring incorporating elastomeric sealing elements (hereafter referred to as “seals”) suitable for the range of shaft diameter from 6mm to 480 mm and the range of housing bore from 16 mm to 530 mm. Seals shall be used under the low-pressure condition of 0kPa to 30kPa in gauge pressure, and classified into six types according to the construction. Respective basic types are as given in figure 1. The seals without spring are shown in Annex JA.

Rotary shaft lip-type seals incorporating elastomeric sealing elements.Part 1: Nominal dimensions and tolerances

JIS B 2402-2:2013 组合弹性密封元件的旋转轴唇型密封件.第2部分:词汇表

Rotary shaft lip-type seals incorporating elastomeric sealing elements.Part 2: Vocabulary