共找到 402 条与 橡胶密封件 相关的标准,共 27 页
The hot compression properties of a gasket material, including creep resistance and compression set, are a major factor with regard to the selection of a given material for use in a particular sealing application. The significance of the test method is based, in part; on the assumption that if a material exhibits too much creep at elevated temperature that it will no longer function as effectively as a seal. This assumption can only be used as a guide; however, since exact yield or failure points are difficult to define for gasket materials (which are usually viscoelastic in nature). Two or more materials can be compared to determine differences in their hot compression properties. A sample of material can be compared to an established standard or previously determined characteristics on original lots of the same material, for quality assurance purposes. Samples are to be tested with a raised profile insert or calibration ring described in 6.3 and Fig. 1 so that the area (2042 mm2 (3.17 in.2)) remains constant during the test. FIG. 1 Test Assembly for Determining Hot Compression1.1 This test method covers a means of measuring the hot compression properties of a gasket material by measuring its creep under a constant load at both room temperature and while increasing the temperature. Short term creep properties including both cold and hot creep, total creep and compression set of a gasket material can be determined. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Hot Compression Properties of Gasket Materials
本标准规定了洗衣机橡胶水封的基本结构、尺寸代号及尺寸标志、要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于轴径为10mm-100mm、工作压力不大于0.05MPa的全自动波轮洗衣机和全自动滚筒洗衣机橡胶水封。
Rubber seals used in shaft of washing machine
本标准规定了耐酸碱橡胶密封件材料的分类和标记、要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于一般耐硫酸、盐酸、硝酸、氢氧化钠、氢氧化钾的橡胶密封件材料。
Acid and alkali resistant rubber compounds for seals
本标准规定了滚筒洗衣机橡胶门封的分类、要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于烘干型和非烘干型滚筒洗衣机橡胶门封。
Rubber seals for washing machine window
Fluid power systems - O-rings - Part 1: Inside diameters, cross-sections, tolerances and designation codes; Technical Corrigendum 2
Rotary shaft lip-type seals incorporating elastomeric sealing elements - Part 3: Storage, handling and installation
이 표준은 50 ℃ 이하의 사용 온도에서 가스 연료(제조된 것이나 또는 천연 가스) 공급
Rubber seals-Joint rings used for gas supply pipes and fittings-Specification for material
이 표준은 석유 공급 파이프와 피팅을 위해 가황된 고체 고무 씰(seal)용 링으로 쓰이는
Rubber seals-Joint rings used for petroleum product supply pipes and fittings-Specification for material
Covers the requirements for two types (see 3.1) of one-component solvent-free silicone-rubber-base sealing compounds for the building industry, and that are suitable for both interior and exterior use.
Sealing compounds for the building industry, one-component, silicone-rubber-base
Rotary-shaft lip-type seals incorporating elastomeric sealing elements - Part 2 : vocabulary.
Rotary shaft lip-type seals incorporating elastomeric sealing elements - Vocabulary
This specification covers high temperature, compression set and fluid resistant fluorocarbon elastomer material to be used in the form of sheet, strip, tubing, extrusions and molded shapes for aeronautical and aerospace applications. This specification should not be used to address products such as O-rings, compression seals, O-ring cord, and molded-in-place gaskets. For those applications AMS7379 should be used. These products have resistance to a variety of gas turbine engine oils, including high thermal stability (HTS) oils, fuels, and hydraulic fluids, but usage is not limited to such applications. Each application should be considered separately. This fluorocarbon (FKM) has a service temperature range of -60 to +400°F (-51 to +204°C) in air.
Rubber: Fluorocarbon Elastomer (FKM) 70 to 80 Hardness, Low Temperature Sealing Tg -40°F (-40°C)for Elastomeric Parts in Aircraft Engine Oil, Fuel and Hydraulics Systems
Covers the requirements for non-cellular vulcanized rubber joint rings for use in pressure cookers.
Rubber joint rings (non-cellular) Part 3: Joint rings for use in pressure cookers
1.1 This specification covers preformed rubber gaskets used to seal joints in cast iron soil pipe and fittings. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 The committee with jurisdiction over this standard is not aware of another comparable standard for materials covered in this standard.
Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings
이 표준은 마실 수 있거나 또는 없는 온수(110 ℃ 이하) 공급기용 가황 고무 씰(sea
Rubber seals-Joint rings for pipelines for hot-water supply up to 110 ℃-Specification for the material
本标准规定了贮气柜用橡胶密封膜(以下简称密封膜)的要求、检验规则、试验方法、标志、包装、运输和贮存。 本标准适用于设计压力在6kPa以下,用于冶金、石油化工、城市煤气工程、煤炭污水处理等行业贮存转炉煤气、高炉煤气、炼油厂尾气、石油拌生气、矿井气、沼气和天然气等气体的贮气柜用橡胶密封膜。 本标准不适用于由经纬交织结构为基材的贮气柜用橡胶密封膜。
Rubber Sealing Membrane for Gas Holder
本标准规定了普通液压系统耐石油基液压油和润滑油的往复运动橡胶密封圈材料的分类、要求、试验方法及标志、标签、包装、贮存。 本标准适用于在普通液压系统耐石油基液压油和润滑油中使用的往复运动橡胶密封圈材料。
Compounds of reciprocating rubber seals
本标准规定了普通液压系统耐石油基液压油和润滑油(脂)用O形橡胶密封圈材料的分类、要求、试验方法、检验规则及标识、包装、贮存。 本标准适用于普通液压系统耐石油基液压油和润滑油(脂)、工作温度范围分别为-40℃~+100℃和-25℃~+125℃的O形橡胶密封圈材料。
Rubber Compounds of O-Rings used for Hydraulic fluid power System
Rotary shaft lip-type seals incorporating elastomeric sealing elements - Nominal dimensions and tolerances
1.1 This specification covers the material requirements for preformed polychloroprene elastomeric joint seals for bridges. The seal consists of a multiple-web design composed of polychloroprene and functions only by compression of the seal between the faces of the joint with the seal folding inward at the top to facilitate compression. The seal is installed with a lubricant adhesive and is designed to seal the joint and reject incompressibles. Note 18212;This specification may not be applicable for seals whose height is less than 90 % of its nominal width. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Bridges
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号