J00 标准化、质量管理 标准查询与下载

EN 818-6:2000+A1:2008 起重用短环链.安全.第6部分:制造商提供的使用和维护信息规范

This Part of EN 818 specifies the information on use and maintenance to be provided by the manufacturer with chain slings conforming to EN 818-4:1996+A1 and EN 818-5:1999+A1. NOTE Certain clauses are relevant to component parts of chains and accessories conforming to EN 818-2:1996+A1, EN 818-3:1999+A1 and EN 1677. Annex A is informative, and provides some of the detailed information for use and maintenance which may be appropriate. The hazards covered by this Part of EN 818 are identified in clause 4.

Short link chain for lifting purposes - Safety - Part 6: Chain slings - Specification for information for use and maintenance to be provided by the manufacturer

CGA C-16.1-2008 压缩气体协会(CGA)汽缸所有者注册标记及公司名称

This publication lists the CGA-registered symbols and companies owning them. Since this will be updated regu- larly, it will be republished more often than CGA C-16, CGA Cylinder Registration Program For Cylinder Owner Symbols.

CGA cylinder owner's registration symbols and company names

CGA C-16-2008 汽缸所有者标记用压缩气体协会(CGA)汽缸注册程序

This publication explains CGA's program for registering cylinder ownership symbols and is intended for cylinder owners and those interested in understanding cylinder ownership symbols.

CGA cylinder registration program for cylinder owner symbols

KS B ISO 16432:2007 电阻焊.使用压纹凸焊法对无覆层和覆层低碳钢进行凸焊的程序

이 규격은 두께 0.4∼3 mm의 판재에 대한 2겹의 비도금 및 금속 도금 저탄소강의 조립

Resistance welding－Procedure for projection welding of uncoated and coated low carbon steels using embossed projection(s)

KS B 6947-2007 机械安全性.防止上肢接近危险区域的安全距离

? ??? 3? ??? ??? ???? ?? ???? ?? ?? ??? ???? ?? ??

Safety of machinery-Safety distances to prevent danger zones being reached by the upper limbs

KS B 6954-2007 机械安全性.风险评估的原则

? ??? ?? ??? ?? ???? ???? ?? ??? ???? ??? ???? ???

Safety of machinery-Principles for risk assessment

KS B 6953-2007 机械安全性.防止意外启动

? ??? EN 1037 ??? ??? ?? ??? ??? ???? ?? ??? ?????

Safety of machinery-Prevention of unexpected start-up

ASME PCC-3-2007 用基于风险法的检验计划

The risk analysis principles, guidance, and implementation strategies presented in this Standard are broadly applicable; however, this Standard has been specifically developed for applications involving fixed pressurecontainingequipment and components. This Standardis not intended to be used for nuclear power plant components;see ASME BPV, Section XI, Rules for InserviceInspection of Nuclear Power Plant Components. It provides guidance to owners, operators, and designers of pressure-containing equipment for developing and implementing an inspection program. These guidelines include means for assessing an inspection program and its plan. The approach emphasizes safe and reliable operation through cost-effective inspection. A spectrum of complementary risk analysis approaches (qualitative through fully-quantitative) should be considered as part of the inspection planning process.

Inspection Planning Using Risk-Based Methods

KS B ISO 15261:2007 振动和冲击发生系统.词汇

이 규격은 진동 및 충격 발생 시스템에 관련된 용어의 정의에 대하여 규정한다.이러한 발

Vibration and shock generating systems－Vocabulary

IPC TM-650 2.4.28.1-2007 磁带测试方法下的焊接面罩粘附 修订版F

Shown above are the experts who participated i n the panel discussion on t h i n copper foils. The entire program covered i n this report was developed by Program Chairman Bernard A7 zua , CuTronics.

Solder Mask Adhesion - Tape Test Method Revision F

IPC TM-650 2.6.14-2007 抵抗电化学迁移的焊接面罩 修订版C

Cette norme est une collection visuelle des exigences de l’acceptabilité de la qualité pour les assemblages

Solder Mask - Resistance to Electrochemical Migration Revision D

BS 8888:2006 技术产品规范(TPS).规范

This British Standard specifies requirements for the preparation of all forms of technical product specification. The requirements cross-refer substantially to International and European Standards which have been implemented as British Standards either in the BS ISO, BS EN, BS EN ISO series or as International Standards re-numbered as British Standards. The requirements are supplemented by commentary and recommendations on technical matters that are considered to be of assistance to users of this standard in the UK and which do not conflict with published International Standards in this field. Annex A and Annex B list cross-referenced standards and other documents, normative and informative respectively, by primary reference. Annex C (normative) sets out requirements for enhanced document security. Annex D (informative) identifies the main differences in approach between the provisions of this standard and those of the American Society of Mechanical Engineers (ASME) Y14.5:1994. Annex E (informative) provides a brief history of the development of BS ISO 1101. Annex F (informative) provides a summary report on the concepts that have underwritten the development of technical product specification (TPS) and its primary constituent, geometrical product specification (GPS), to date and discusses some of the drivers for future change. Annex G (informative) gives the rationale behind the development of BS 8888. Annex H (informative) gives a list of recommended default choices in response to options that are available in the body of BS 8888.

Technical product specification (TPS) - Specification

JB/T 5058-2006 机械工业产品质量特性重要度分级导则

本标准规定了机械工业产品质量特性重要度分级（以下简称重要度分级）的原则、内容和要求及标注方法。 本标准适用于机械工业产品的重要度分级。

Foreword of mechanical industry product quality characteristic essentiality classification

JB/T 5057-2006 机械工业企业产品质量事故分类

本标准规定了机械工业企业产品质量事故的定义和分类方法。 本标准适用于机械工业企业产品质量事故的管理。

Category of enterprise product quality accident in mechanical industry

AGMA 05FTM20-2005 双驱动输送机减速器故障分析

With increasing requirements, many conveyor systems utilize dual drive arrangements to increase output. Dual drives can provide an economical solution by utilizing smaller, more efficient, system designs. However, multiple drive conveyors must proportion the load between drives and load sharing without some type of control is difficult to achieve. This paper presents a case study on a failure analysis of a coal mine dual drive conveyor system that experienced gear reducer failures between 2 to 18months. Physical and metallurgical inspection of failed gearing did not indicate material or workmanship defects, but indicated overload. In order to determine the cause of the failures, strain gage load testing was performed. The testing of the conveyor drives revealed load sharing problems which that will be reviewed.

Dual Drive Conveyor Speed Reducer Failure Analysis

AGMA 05FTM18-2005 Planet Pac:通过集成提高周转功率的密度和性能

Epicyclical gear systems are typically equipped with straddle--mounted planetary idlers and are supported by pins on the input and output sides of a carrier. These carriers can be either one--piece or two--piece carrier designs. Traditionally many of the higher power rated epicyclic gear systems use cylindrical roller bearings to support the planetary gears. This paper will demonstrate that using a preloaded taper roller bearing in an integrated package should be the preferred choice for this application to increase the bearing capacity, power density, and fatigue life performance. Based on DIN281--4 calculations, this patented [1], fully integrated solution allows for calculated bearing fatigue lives to be 5 times greater than a non--integrated solution and more than 1.5 times greater than a semi--integrated solution, without changing the planet gear envelope.

Planet Pac: Increasing Epicyclic Power Density and Performance Through Integration

AGMA 05FTM02-2005 渗碳期间预粗糙机械加工对空间扭曲的影响

A study was conducted to isolate the influence of pre--rough machine processing on final dimensional distortion. Methods are discussed to aid process development and minimize dimensional change during carburizing. The study examined the distortion during carburizing between five possible raw material starting conditions. Coupons were used and manufactured from each population ofmaterial processing. All coupons were carburized and hardened at the same time. Dimensions were made before and after carburizing using a scanning coordinatemeasurement machine. The results show that dimensional distortion during carburizing increases with mechanical and thermal processing.

The Effects of Pre Rough Machine Processing on Dimensional Distortion During Carburizing

BS 8888:2004 技术产品规范(TPS).规范

This British Standard specifies requirements for the preparation of all forms of technical product specification. The requirements cross-refer substantially to International and European Standards which have been implemented as British Standards either in the BS ISO, BS EN, BS EN ISO series or as International Standards re-numbered as British Standards. The requirements are supplemented by commentary and recommendations on technical matters that are considered to be of assistance to users of this standard in the UK and which do not conflict with published International Standards in this field. Annex A and Annex B list cross-referenced standards and other documents, normative and informative respectively, by primary reference, indicating the Standards Kit (see Note) in which they can be found. Annex C (normative) provides a list of standard symbols and abbreviations. Annex D (normative) sets out requirements for enhanced document security and Annex E (normative) identifies the main differences in approach between the provisions of this standard and those of the American Society of Mechanical Engineers (ASME) Y14.5 series. Annex F (informative) provides a summary report on the concepts that have underwritten the development of technical product specification (TPS) and its primary constituent, geometrical specification, to date and discusses some of the drivers for future change. NOTE This British Standard is available in CD-ROM format, in which form it is accompanied by the full range of cross-referenced standards, all hyperlinked to the relevant reference(s) within the text of the primary standard. When used in paper form, it is necessary that this standard be used in conjunction with the relevant cross-referenced standards. To facilitate this, four Standards Kits are available under the general heading BS 8888, Technical Product Specification, with each kit comprised of a group of the cross-referenced standards relating to a particular aspect of the scope of BS 8888.

Technical product specification (TPS) - Specification

ASME B002DM-2004 第II节:第D部分.性能(米制).到期日:2004年7月

Boiler and Pressure Vessel.Section II: Part D - Properties (Metric) Due July 2004

Section II: Part D - Properties (Metric) Due July 2004

ASME B00230-2004 完全法规.到期日:2004年7月

Complete Code Due July 2004

Complete Code Due July 2004