J48 气动工具 标准查询与下载
共找到 179 条与 气动工具 相关的标准，共 12 页
本标准规定了冲击式机动四方传动套筒工作端为六角或双六角的尺寸、标记和标志。 手动套筒的尺寸见 ISO 2725－1。 注 1 冲击式机动四方传动套筒列于ISO 1703中第301项。 2 本标准中的图形只作为示例，并不影响制造厂的设计。 本标准适用于冲击式机动四方传动套筒（以下简称套筒）。
Assembly tools for screws and nuts-Machine-operated square drive sockets ("impact")-Dimensions
- ICS
- 25.140.01
- CCS
- J48
- 发布
- 2000-10-17
- 实施
- 2001-07-01
Gas tank for gas powered nail gun
- ICS
- 25.140.10
- CCS
- J48
- 发布
- 2020-08-31
- 实施
- 2021-04-01
This Standard applies to portable power tools for drilling, grinding, polishing, sawing, and driving threaded fasteners,and hand tools for driving threaded fasteners. Other tools not classed as percussion tools belong in this category and may be added by revision or addition through the usual procedure. This Standard includes dimensions and tolerances for both driving and driven elements where such coordination is important and not established by reference to the pertinent American National Standards. All dimensions are in inches and millimeters. 本标准适用于钻孔、研磨、抛光、锯切和驱动螺纹紧固件的便携式电动工具，以及用于驱动螺纹紧固件的手动工具。其他未归类为打击工具的工具也属于此类，通过通常的程序修改或添加。 本标准包括主动和从动元件的尺寸和公差很重要且未参考相关美国国家标准而建立。所有尺寸均以英寸和毫米为单位。
Driving and Spindle Ends for Portable Hand, Impact, Air, and Electric Tools (Percussion Tools Excluded)
- ICS
- 25.140.01
- CCS
- J48
- 发布
- 2019-05-10
- 实施
- 2019-05-10
Pneumatic pressure paint bucket
- ICS
- 25.140.10
- CCS
- J48
- 发布
- 2017-11-07
- 实施
- 2018-04-01
This document specifies a laboratory performance test method for power assembly tools (referred throughout the document as “tool”) for installing threaded fasteners. It provides a method for the measurement of torque repeatability (scatter) — over a range of torque rates as specified in this document, — over a range of torque adjustment as defined by the manufacturer, and — over a number of operating cycles as defined by the manufacturer. It provides a method for the measurement of the precision of the built-in torque measurement system for tools incorporating such a feature. See Annex E. It gives instructions on equipment parameters, what to test for and how to evaluate and present the test data. It is applicable to tools — of any power source, e.g. pneumatic, hydraulic, and electric, including battery-powered, — which apply torque in a generally continuous manner, and — within the torque range 0,5 Nm to 2000 Nm. Outside this range, it is acceptable to modify the test method providing that the modification is documented in the test report. It is not applicable to — impact or impulse wrenches, — ratchet wrenches or wrenches with ratcheting clutches, and — other tools which advance fasteners in discontinuous increments, overcoming static friction at each increment. It allows a test to be performed at any test torque level; however, in order to minimize the number of test joints necessary for a wide range of test torque levels, a list of preferred test torque levels is provided in Annex A.
Rotary tools for threaded fasteners - Performance test method
- ICS
- 25.140.10
- CCS
- J48
- 发布
- 2017-11-01
- 实施
This document specifies safety requirements for hand-held non-electric power tools (hereinafter referred to as “fastener driving tools”) intended for installation of a fastener (see Annex B), forming a mechanical connection or attachment with the workpiece which are for example wood and woodbased materials, plastic materials, fibre materials (loose or compacted), cementitious materials, metals and combinations of these materials. The fastener driving tools for fasteners can be powered by compressed air or combustible gases (which may be ignited by a battery or accumulator) and the energy is transmitted to an impacted element by an intermediary component that does not leave the device. These tools are intended to be used by one operator and supported by the operator's hand or hands, with or without a suspension, e.g. a balancer. This document is applicable to fastener driving tools in which energy is applied to a loaded fastener for the purpose of driving this into a workpiece. This document is not applicable to fastener driving tools in which the energy for driving fasteners is drawn from powder-actuated cartridges, hydraulics or from any type of electrical supply. This document does not deal with special requirements and modifications of hand-held power tools for the purpose of mounting them in a fixture. This document deals with all significant hazards, hazardous situations or hazardous events relevant to fastener driving tools for fasteners when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, with the exception of the use of power tools in potentially explosive atmospheres. NOTE
Hand-held non-electric power tools - Safety requirements - Part 13: Fastener driving tools
- ICS
- 25.140.10
- CCS
- J48
- 发布
- 2017-11-01
- 实施
Straight handle pneumatic grinder
- ICS
- 25.140.10
- CCS
- J48
- 发布
- 2016-04-05
- 实施
- 2016-09-01
本标准规定了气动捣固机用捣头的型式与尺寸、技术要求、检验方法、检验规则、标志、包装、运输和贮存。 本标准适用于气动捣固机用捣头(以下简称捣头)的设计、制造、验收与使用。
Tamping butts for pneumatic tampers
- ICS
- 25.140.01
- CCS
- J48
- 发布
- 2016-04-05
- 实施
- 2016-09-01
本标准规定了液压脉冲定扭矩扳手的术语和定义、型式、型号与基本参数、技术要求、检验方法、检验规则、标志、包装、运输和贮存。 本标准适用于以压缩空气为动力的液压脉冲定扭矩扳手(以下简称产品)。
Hydraulic impulse torque wrenches
- ICS
- 25.140.10
- CCS
- J48
- 发布
- 2015-10-10
- 实施
- 2016-03-01
