J74 压力容器 标准查询与下载
共找到 1982 条与 压力容器 相关的标准，共 133 页
本标准规定了带式真空过滤机的技术要求、试验方法、检验规则等。 本标准适用于移动室和滤带间歇运动带式真空过滤机。 本标准不适用于固定室带式真空过滤机。
Belt vacuum filter technical conditions
- ICS
- 73.120
- CCS
- J74
- 发布
- 1991-12-07
- 实施
- 1992-10-01
本标准规定了在用铝合金无缝气瓶（以下简称铝瓶）定期技术检验与评定的基本方法和技术要求， 本标准适用于按GB 11640《铝合金无缝气瓶》设计、制造，公称容积不超过50L，公称工作压力为1～20MPa，用于储存和运输永久气体或液化气体，并可重复充气的移动式铝瓶。 凡按《进出口锅炉压力容器监督管理办法》的有关规定，经监督检验合格的进口同类铝瓶，参照本标准的规定进行定期检验。 本标准不适用于机器设备上的附属铝瓶、填有固体充填物的铝瓶，钢丝缠绕式铝瓶以及灭火用铝瓶。
Periodic inspection and evaluation of seamless aluminium alloy gas cylinders
- ICS
- 23.020.30
- CCS
- J74
- 发布
- 1991-07-12
- 实施
- 1992-04-01
本标准规定了溶解乙炔气瓶的定期检验与评定。 本标准适用于基准温度15℃时限定充装压力小于1．52MPa、最高许用温度40℃、公称容积10～60L、内含多孔填料和溶剂、移动式、可重复充气的钢质焊接式溶解乙炔气瓶（以下简称乙炔瓶）。
Periodic inspection and evaluation of dissolved acetylene cylinders
- ICS
- 23.020.30
- CCS
- J74
- 发布
- 1991-07-12
- 实施
- 1992-04-01
本标准规定了在用溶解乙炔气瓶（以下简称乙炔瓶）气压试验的基本方法和技术要求。 本标准适用于在用乙炔瓶的定期检验和评定中的气压试验。 本标准不适用于化工生产过程中盛装溶解乙炔容器的气压试验。
Method for pneumatic test of dissolved acetylene cylinders
- ICS
- 23.020.30
- CCS
- J74
- 发布
- 1991-04-23
- 实施
- 1992-01-01
本标准规定了气瓶的常用术语及其含义。 本标准适用于各类气瓶基础标准、方法标准、产品标准和管理标准的技术用语。
Terminology of gas cylinders
- ICS
- 23.020.30
- CCS
- J74
- 发布
- 1991-04-23
- 实施
- 1992-01-01
本标准规定了溶解乙炔气瓶阀的基本型式及结构尺寸、技术要求、试验方法和检验规则。 本标准适用于溶解乙炔气瓶的阀门（以下简称阀），阀的公称压力为3MPa（表压，下同）。
Valves for dissolved acetylene cylinders
- ICS
- 23.020.30
- CCS
- J74
- 发布
- 1989-03-31
- 实施
- 1990-01-01
本标准规定了氧气瓶阀的基本型式、技术要求和检测方法。本标准适用于公称工作压力不大于30MPa的氧气瓶上的阀门，也适用于公称工作压力不大于30MPa的氮气和空气瓶上的阀门。 本标准不适用于高纯氧、氮气瓶上的阀门。注：本标准的压力均指表压。
Valves for oxygen cylinders
- ICS
- 23.020.30
- CCS
- J74
- 发布
- 1989-03-31
- 实施
- 1990-01-01
本标准规定了直管状铝无管芯重力热管的品种规格、技术要求和检验方法。 本标准适用于铝无管芯重力热管的设计、制造和检验。
Wickless aluminium gravity heat pipes
- ICS
- 23.040.15
- CCS
- J74
- 发布
- 1988-04-14
- 实施
- 1988-11-01
本标准规定了无管芯重力热管铝管材的技术要求和检验方法。 本标准适用于无管芯重力热管铝管材的生产和验收。
Aluminium tubes used for wickless gravity heat pipes
- ICS
- 23.040.15
- CCS
- J74
- 发布
- 1988-04-14
- 实施
- 1988-11-01
General requirements for the construction of gas cylinder quality and safety traceability information systems
- ICS
- 23.020.30
- CCS
- J74
- 发布
- 2024-01-09
- 实施
- 2024-04-09
Regular inspection rules for polyethylene (PE) gas pipelines
- ICS
- 23.040
- CCS
- J74
- 发布
- 2024-01-09
- 实施
- 2024-04-09
Specifications for periodic inspection of station gas storage cylinder sets
- ICS
- 23.020.30
- CCS
- J74
- 发布
- 2023-12-19
- 实施
- 2023-12-31
本文件适用于公称工作压力不大于30 MPa，单只气瓶公称水容积4 L～450 L盛装洁净氮气、氩气、氦气、二氧化碳、七氟丙烷、六氟丙烷、全氟己酮等单一气体或混合气体可重复充装站用钢质储气瓶组的安全性评价。柜式七氟丙烷可参照本文件执行。
Safety evaluation method for gas storage cylinder sets used in stations
- ICS
- 23.020.30
- CCS
- J74
- 发布
- 2023-12-18
- 实施
- 2024-01-01
Steam boiler emergency response guidelines
- ICS
- 23.020.30
- CCS
- J74
- 发布
- 2023-08-22
- 实施
- 2023-11-22
Technical Guidelines for Manufacturing Supervision and Inspection of Skid-Mounted Pressure-Containing Equipment Systems
- ICS
- 13.100
- CCS
- J74
- 发布
- 2022-06-10
- 实施
- 2022-07-01
Technical specification for low-nitrogen transformation of gas-fired boilers (facilities)
- ICS
- 23.020.30
- CCS
- J74
- 发布
- 2022-01-29
- 实施
- 2022-04-29
This document specifies the minimum requirements for the materials, design, construction and workmanship, manufacturing processes, examinations and testing at time of manufacture for refillable, seamless, stainless steel gas cylinders with water capacities up to and including 150 l. It is applicable to cylinders for compressed, liquefied and dissolved gases with a maximum actual tensile strength, Rma, of less than 1100 MPa. NOTE If so desired, cylinders of water capacity between 150 l and 450 l can be manufactured to be in full conformance to this document.
Gas cylinders - Design, construction and testing of refillable seamless steel gas cylinders and tubes - Part 4: Stainless steel cylinders with an Rm value of less than 1100 MPaj74
- ICS
- CCS
- J74
- 发布
- 2021-11-00
- 实施
This document gives guidance on the selection and evaluation of compatibility between non-metallic materials for gas cylinders and valves and the gas contents. It is also applicable to tubes, pressure drums and bundles of cylinders. This document covers composite and laminated materials used for gas cylinders. It does not include ceramics, glasses and adhesives. This document considers the influence of the gas in changing the material and mechanical properties (e.g. chemical reaction or change in physical state). The basic properties of the materials, such as mechanical properties required for design purposes (normally available from the materials supplier), are not considered. Other aspects, such as quality of delivered gas, are not considered. The compatibility data given are related to single component gases but can be applicable to gas mixtures. This document does not apply to cryogenic fluids (this is covered in ISO 21010).
Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 2: Non-metallic materials
- ICS
- CCS
- J74
- 发布
- 2021-10-00
- 实施
本文件规定了工业管道的编码规则、编码对象、代码结构和组成、编码符号表示。
Coding rules and symbols for industrial piping
- ICS
- 23.040
- CCS
- J74
- 发布
- 2021-09-25
- 实施
- 2021-10-01
