J74 压力容器 标准查询与下载

DB31/T 1258-2020 气瓶管理信息报文格式规范

Format specification of gas cylinder management information message

BS PD CEN/TR 14473:2020 移动式气瓶. 乙炔气瓶的多孔材料

Transportable gas cylinders. Porous materials for acetylene cylinders

ISO 11119-3:2020 气瓶. 可二次填充的混合气瓶和导管的设计,安装和测试. 第3部分: 容量不高于450 L带非负载分配金属或非金属衬层或无衬层的完全包装纤维增强复合材料气瓶和管道

This document specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at time of manufacture for: — type 4 composite fully wrapped cylinders or tubes with a non-load sharing liner and composite reinforcement on both the cylindrical portion and the dome ends; — type 5 fully wrapped cylinders or tubes without liners and with a test pressure of less than 60 bar and composite reinforcement on both the cylindrical portion and the dome ends; — water capacities up to 450 l; — for the storage and conveyance of compressed or liquefied gases; — cylinders and tubes with composite reinforcement of carbon fibre, aramid fibre or glass fibre (or a mixture thereof) within a matrix; — a minimum design life of 15 years. Cylinders and tubes manufactured and tested according to this document are not intended to contain toxic, oxidizing or corrosive gases. This document does not address the design, fitting and performance of removable protective sleeves. NOTE 1 References to cylinders in this document include composite tubes if appropriate. NOTE 2

Gas cylinders - Design, construction and testing of refillable composite gas cylinders and tubes - Part 3: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450 l with non-load-sharing metallic or non-metallic liners or without liners

ISO 11119-2:2020 气瓶. 可二次填充的混合气瓶和导管的设计,安装和测试. 第2部分: 容量大于450 L带有负载分配金属衬壳的完全包裹纤维增强复合材料气瓶和导管

This document specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at time of manufacture for: — type 3 fully wrapped cylinders or tubes with a load-sharing metal liner and composite reinforcement on both the cylindrical portion and the dome ends; — water capacities up to 450 l; — storage and conveyance of compressed or liquefied gases; — cylinders and tubes with composite reinforcement of carbon fibre, aramid fibre or glass fibre (or a mixture thereof) within a matrix; — a minimum design life of 15 years. This document does not address the design, fitting, and performance of removable protective sleeves. This document does not apply to cylinders with welded liners. NOTE 1 References to cylinders in this document include composite tubes if appropriate. NOTE 2

Gas cylinders - Design, construction and testing of refillable composite gas cylinders and tubes - Part 2: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450 l with load-sharing metal liners

ISO 11119-1:2020 气瓶. 可可二次填充的混合气瓶和导管的设计,安装和测试. 第1部分: 小于等于450 L的箍围纤维增强复合气体储气瓶和管

This document specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at time of manufacture for: — type 2 composite hoop wrapped cylinders or tubes with a load-sharing metal liner and composite reinforcement on the cylindrical portion only; — water capacities up to 450 l; — the storage and conveyance of compressed or liquefied gases; — cylinders and tubes with composite reinforcement of carbon fibre, aramid fibre or glass fibre (or a mixture thereof) within a matrix or steel wire to provide circumferential reinforcement; — a minimum design life of 15 years. This document does not address the design, fitting, and performance of removable protective sleeves. NOTE 1 References to cylinders in this document include composite tubes if appropriate. NOTE 2

Gas cylinders - Design, construction and testing of refillable composite gas cylinders and tubes - Part 1: Hoop wrapped fibre reinforced composite gas cylinders and tubes up to 450 l

DIN EN 16728:2020 液化石油气设备和附件. 传统焊接和钎焊钢瓶以外的液化石油气(LPG)用可运输可再充装气瓶. 定期检查; 德文版本EN 16728-2016+A2-2020

This European Standard specifies procedures for periodic inspection and testing, for transportable refillable LPG cylinders with a water capacity from 0,5 l up to and including 150 l. This European Standard is applicable to the following: - welded steel LPG cylinders manufactured

LPG equipment and accessories - Transportable refillable LPG cylinders other than traditional welded and brazed steel cylinders - Periodic inspection; German version EN 16728:2016+A2:2020

NB/T 47012-2020 制冷装置用压力容器

本文件规定了以液化气体为制冷剂、设计压力不高于5.0MPa、设计温度不高于200℃的制冷装置用压力容器（包括制冷装置用管壳式热交换器，以下简称“容器”）的设计、制造、检验与验收要求。

Pressure vessels for refrigeration equipment

DB43/T 1759-2020 有机热载体炉事故应急救援规范

Emergency Rescue Specifications for Organic Heat Carrier Furnace Accidents

DB43/T 1734-2020 快开门式压力容器联锁装置安全技术要求

Safety technical requirements for interlocking devices of quick-opening pressure vessels

DB42/T 1542-2020 电站锅炉范围内管道安装、改造、重大修理监督检验规则

Supervision and inspection rules for pipeline installation, modification, and major repairs within the scope of power plant boilers

T/CMES 16002-2019 钢制塔式容器风致疲劳寿命计算及评定方法

本标准规定了钢制塔式容器风致疲劳寿命的计算和评定方法。 本标准适用于高度大于30m，且常年处于多风地区的裙座自支撑钢制塔式容器

Calculation and evaluation method of wind-induced fatigue life of steel tower vessel

DB3309/T 35-2019 冷库压力容器、压力管道维护保养管理规范

Specifications for the maintenance and management of pressure vessels and pressure pipelines in cold storage

DB61/T 497-2019 超高压人造水晶釜定期检验规程

本标准适用于设计压力大于等于100MPa的在用水晶釜（包括与水晶釜端口部分连接的承压部件及其紧固件、爆破片）的定期检验

Regulations for periodic inspection of ultra-high pressure artificial crystal kettle

T/CAQI 58-2018 污（废）水生物处理 悬浮填料老化生物膜脱除技术规范

一般要求、设备要求、脱膜剂要求、安全要求。

Biological treatment of sewage and wastewater Technical specification of removal of aging biofilm on suspended filler

DIN EN ISO 13769:2018 气瓶. 钢印标记(ISO 13769-2018); 德文版本EN ISO 13769-2018

This Draft International Standard specifies stamp marking of transportable gas cylinders and tubes of volumes greater than 0,120 l and up to or equal to 3000 l, including: - steel and aluminium-alloy gas cylinders; - composite gas cylinders; - acetylene cylinders; - liquefied petroleum gas (LPG) cylinders (see Annex A); and - small cylinders (see Annex B). These hereafter are referred to as "cylinders."

Gas cylinders - Stamp marking (ISO 13769:2018); German version EN ISO 13769:2018

DB34/T 1799-2018 曳引驱动可变速电梯安装验收技术条件

本标准规定了可变速电梯安装验收应遵守的安全准则。 本标准适用于额定速度不大于 2.5 m/s 的曳引驱动的可变速电梯。 本标准不适用非电力驱动以及强制驱动的可变速电梯。

Technical conditions for installation and acceptance of traction drive variable speed elevators

DB34/T 1707-2018 在役超高压人造水晶釜定期检验规程

本标准规定了在役超高压人造水晶釜定期检验的一般规定、检验项目和内容。 本标准适用于设计压力大于或等于 100 MPa 的在役人造水晶釜（与水晶釜端口部分连接的承压盖 及其紧固件；水晶釜所用的爆破片等安全附件）。

Regulations for periodic inspection of in-service ultra-high pressure artificial crystal kettles

DIN EN 13322-1:2018 可运输气瓶. 可再灌充焊接钢制气瓶. 设计和结构. 第1部分: 碳钢; 德文版本EN 13322-1-2003+A1-2006

This Standard sets out minimum requirements concerning material, design, construction and workmanship, manufacturing processes and testing of refillable transportable welded carbon steel gas cylinders of water capacities from 0,5 l up to and including 150 l for compressed, liquefied and dissolved gases. For acetylene service, additional requirements for the cylinder and the basic requirements for the porous mass are given in EN 1800. For those cylinders made from high frequency induction (HFI) welded steel tubes, the requirements are given in annex A.

Transportable gas cylinders - Refillable welded steel gas cylinders - Design and construction - Part 1: Carbon steel; German version EN 13322-1:2003 + A1:2006

DB31/T 1101-2018 液化石油气钢瓶延长使用期安全评定方法

本标准规定了液化石油气钢瓶(以下简称“钢瓶”)延长使用期安全评定的时机、评定机构、评定基本要求、技术要求和信息化管理的要求。 本标准适用于按照GB 5842《液化石油气钢瓶》设计、制造，且于2007年之后出厂的钢瓶延长使用期的安全评定。

Safety assessment method for extended service life of liquefied petroleum gas cylinders

DIN EN 14025:2018 危险品的运输用槽罐.金属压力槽罐.设计和结构; 德文版本EN 14025-2018

This document specifies the minimum requirements for the design and construction of metallic pressure tanks having a maximum working pressure exceeding 50 kPa (0,5 bar), for the transport of dangerous goods by road and rail and sea. This document includes requirements for openings, closures and structural equipment; it does not cover requirements of service equipment.This document is applicable to liquefied gases including LPG; however for a dedicated LPG standard see EN 12493. For tanks for the transport of cryogenic liquids, EN 13530-1 and EN 13530-2 apply.Design and construction of pressure tanks according to the scope of this document are primarily subject to the requirements of RID/ADR.

Tanks for the transport of dangerous goods - Metallic pressure tanks - Design and construction; German version EN 14025:2018