J96 冷却系统与加热装置 标准查询与下载

NF E32-020-4:1996 工业加热设备.固定人工操作或无人操作的蒸汽或过热蒸汽发生器的安全性.第4部分:商用燃气设备的特定要求

Industrial heating equipment. Safety of steam or superheated steam generators permanently manned or not. Part 4 : specific requirements for commercial gas-fuelled installations.

NF E32-020-1:1996 工业加热设备.固定人工操作或无人操作的蒸汽或过热蒸汽发生器的安全性.第1部分:术语.一般要求

Industrial heating equipment. Safety of steam of superheated steam generators permanently manned or not. Part 1 : terminology . General requirements.

NF E32-100H:1994 蒸汽发生器制造规程.1994年更新

CODE FOR CONSTRUCTION OF STEAM GENERATORS. UPDATING FROM 1994.

NF E32-020-3:1994 工业加热设备.永久性有人操作或无人操作的蒸汽或过热蒸汽发生器的安全性..第4部分:液体燃料设备的特定要求

Industrial heating equipment. Safety of steam or superheated steam generators, permanently manned or not. Part 3 : specific requirements for liquid fuelled installations.

ASTM D1177-94(1998)e1 发动机冷却剂溶液冻结点的标准测试方法

1.1 This test method covers the determination of the freezing point of an aqueous engine coolant solution in the laboratory. Note 18212;Where solutions of specific concentrations are to be tested, they shall be prepared from representative samples as directed in Test Methods D 1176. Secondary phases separating on dilution need not be separated.Note 28212;These products may also be marketed in a ready-to-use form (prediluted).1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Freezing Point of Aqueous Engine Coolants

ASTM D1120-94(1998)e1 发动机冷却剂沸点的标准试验方法

1.1 This test method covers the determination of the equilibrium boiling point of engine coolants. The equilibrium boiling point indicates the temperature at which the sample will start to boil in a cooling system under equilibrium conditions at atmospheric pressure. Note 18212;Engine coolants may also be marketed in a ready-to-use form (prediluted). This test procedure is applicable to diluted solutions as well as to concentrates.Note 28212;The procedure for obtaining a representative test sample of a coolant solution that contains an antileak additive is found in Test Method D 1176.1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Boiling Point of Engine Coolants

ANSI Z21.76-1994 用于液化天然气的燃气通风催化室温加热装置

Details test and examination criteria for unvented catalytic room heaters having input ratings up to and including 40,000 Btu per hour (11 723 W) for use with liquefied petroleum (LP) gases.

Gas-Fired Unvented Catalytic Room Heaters for Use with Liquefied Petroleum (LP) Gases

NF E32-100G:1993 蒸汽发生器制造规程.1993年更新

CODE FOR CONSTRUCTION OF STEAM GENERATORS. UPDATING FROM 1993.

JB/T 6726.1-1993 内燃机冷凝式散热器 技术条件

本标准规定了冷凝式散热器的术语，标记，技术要求，检验方法，检验规则和标志、包装、运输、贮存。 本标准适用于内燃机冷凝式散热器。

Specifications for condensing radiators for internal combustion engines

JB/T 6726.2-1993 内燃机冷凝式散热器 试验方法

本标准规定了冷凝式散热器的试验项目，试验装置，试验条件以及试验结果分析、整理的要求。 本标准适用于内燃机冷凝式散热器。

Test methods for condensing radiators of internal combustion engines

JB/T 6723.2-1993 内燃机冷却风扇 第二部分：塑料冷却风扇技术条件

本标准规定了内燃机塑料冷却风扇产品分类，产品标记方法，技术要求，检验规则，标志、包装、运输及贮存。 本标准适用于外径不大于750mm的水冷式、油冷式内燃机塑料冷却风扇。

Cooling fans for internal combustion engines Part II: Specifications for plastic cooling fans

JB/T 6723.1-1993 内燃机冷却风扇 第一部分：金属冷却风扇技术条件

本标准规定了内燃机金属冷却风扇产品分类，产品标记，技术要求，检验规则及标志、包装、运输、贮存的要求。 本标准适用于外径不大于750mm的水冷式、油冷式内燃机金属冷却风扇。

Cooling fans for internal combustion engines Part 1: Specifications for metal cooling fans

JB/T 6718-1993 内燃机冷却水泵V带轮 技术条件

本标准参照采用ISO 4183-14980、ISO 2790-1980和IS为255-1981。 本标准规定了内燃机冷却水泵V带传动用带轮的术语，技术要求，检验方法，检验规则和标志、包装、运输、贮存。 本标准适用于中小功率内燃机冷却水泵V带轮。

Specifications for internal combustion engine cooling water pump V-pulley

BS 5117-0:1992 发动机浓缩冷却剂.("防冻剂")防腐蚀试验.第0部分:总则

Describes the structure of the other Parts and Sections of BS 5117, defines terms used and gives guidance on the significance of test results and comments on the test conditions chosen for corrosion inhibition testing.

Testing corrosion inhibiting, engine coolant concentrate ('antifreeze') - General introduction

JB/T 6009-1992 小功率柴油机水箱 技术条件

　　本标准规定了小功率柴油机水箱的技术要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于小功率柴油机蒸发式薄钢板水箱。

Technical conditions for small power diesel engine water tank

BS 5117 Sec.2.6:1992 防腐蚀试验.发动机浓缩冷却剂(防冻剂).第2部分:防腐蚀性能试验方法.第6节:热交换条件下铸铝合金的防腐蚀试验

Testing corrosion inhibiting, engine coolant concentrate ('antifreeze'). Methods of test for corrosion inhibition performance. Test for corrosion of cast aluminium alloys under heat-transfer conditions

BS 5117 Sec.1.5:1992 防腐蚀试验.发动机浓缩冷却剂(防冻剂).第1部分:测定物理和化学特性的试验方法.第5节:冷却硬水稳定性试验

Testing corrosion inhibiting, engine coolant concentrate ('antifreeze'). Methods of test for determination of physical and chemical properties. Coolant hard water stability test

prHD 610 S1-1992 感应槽电炉的试验方法

Test methods for induction channel furnaces (IEC 396:1991)

ASME PTC 12.4-1992 脱湿器再热装置

This Code provides the procedures, direction, and guidance for the accurate testing of Moisture Separator Reheaters (MSRs) which includes moisture separating and steam reheating components located between the high pressure and low pressure steam turbine. The purpose of the Code is to determine the performance of the MSR and to provide guidance in the evaluation of its performance effect on the turbine cycle heat with regard to: (a) Moisture Separator Outlet Quality; (b) Reheater Terminal Temperature Difference (TTD) per stage; (c) Cycle Steam pressure drop across applicable component(s); and (d) Excess heating steam flow. Requirements are specified by this Code for application on MSR testing in the following areas: (a) Pretest arrangements and agreements; (b) Instrumentation types and accuracies; (c) Instrumentation applications and methods of measurement; (d) Testing and calculation techniques; (e) Information contained in the report.

Moisture Separator Reheaters

NF E32-100B:1991 蒸汽发生器制造规程.1991年更新

CODE FOR CONSTRUCTION OF STEAM GENERATORS. UPDATING FROM 1991.