K10 电工材料和通用零件综合 标准查询与下载

UL 2556-2007 电线和电缆的试验方法

This standard describes the apparatus, test methods, and formulas to be used in carrying out the tests and calculations required by wire and cable standards. Note: Specific acceptance requirements are found in individual product standards.

Wire and cable test methods

KS C 8326-2007 住宅用分线板

이 규격은 교류 60 Hz의 단상 2선식 110 V, 220 V 또는 단상 3선식 110/

Low voltage panelboards for household use

SANS 5516:2007 环形软线的抗弯折性

Describes a method for determining the kink resistance of circular flexible cords.

Kink resistance of circular flexible cords

SANS 5515:2007 软线弯曲试验

Specifies a method for conducting the flexing test on flexible cords.

Flexing test on flexible cords

IEC 60446:2007 人机界面、标志和标识的基本原则和安全原则.用颜色或字母数字来标识导体

This International Standard provides general rules for the use of certain colours or alphanumerics to identify conductors with the aim of avoiding ambiguity and ensuring safe operation. These conductor colours or alphanumerics are intended to be applied in cables or cores, busbars, electrical equipment and installations.

Basic and safety principles for man-machine interface, marking and identification - Identification of conductors by colours or alphanumerics

IEC 60189-2:2007 聚氯乙烯(PVC)绝缘和聚氯乙烯(PVC)护套的低频电缆和电线.第2部分:内部安装用双芯、三芯、四芯和五芯电缆

This part of IEC 60189 is applicable to cables for inside installations, intended for the interconnection of the following: – transmission equipment; – telecommunications equipment; – equipment for data processing. NOTE It is the responsibility of the manufacturer to establish quality assurance by quality control procedures which will ensure that the product will meet the requirements of this standard. It is not intended that a complete testing programme must be carried out on every length of conductor and cable. When the purchaser wishes to specify acceptance tests or other quality procedures, it is essential that agreement be reached between the purchaser and the manufacturer by the time of ordering.

Low-frequency cables and wires with PVC insulation and PVC sheath - Part 2: Cables in pairs, triples, quads and quintuples for inside installations

IEC 60189-3:2007 聚氯乙烯(PVC)绝缘材料和聚氯乙烯(PVC)护套的低频电缆和电线.第3部分:带聚氯乙烯(PVC)绝缘的单股、双股和三股实心或绞合导线的设备电线

This part of IEC 60189 is applicable to equipment wires with solid or stranded conductor, polyvinyl chloride (PVC) insulated, in singles, pairs and triples to be used for internal wiring of telecommunication equipment, industrial and consumer electronic equipment. NOTE It is the responsibility of the manufacturer to establish quality assurance by quality control procedures which will ensure that the product will meet the requirements of this standard. It is not intended that a complete testing programme must be carried out on every length of conductor. When the purchaser wishes to specify acceptance tests or other quality procedures, it is essential that agreement be reached between the purchaser and the manufacturer by the time of ordering.

Low-frequency cables and wires with PVC insulation and PVC sheath - Part 3: Equipment wires with solid or stranded conductor wires, PVC insulated, in singles, pairs and triples

IEC 60189-1:2007 聚氯乙烯(PVC)绝缘材料和聚氯乙烯(PVC)护套的低频电缆和电线.第1部分:一般试验和测量方法

This part of IEC 60189 specifies mechanical, electrical and climatic test methods for lowfrequency cables and wires designed for use in telecommunication inside plant and equipment and in electronic devices employing similar techniques.

Low-frequency cables and wires with PVC insulation and PVC sheath - Part 1: General test and measuring methods

DIN EN 61788-10:2007 超导性.第10部分:临界温度测量.用电阻法测量复合超导体的临界温度(IEC 61788-10-2006)

Superconductivity - Part 10: Critical temperature measurement - Critical temperature of composite superconductors by a resistance method (IEC 61788-10:2006); German version EN 61788-10:2006

DIN 14680:2007 手动电缆盘.交流电、三相交流电和直流电

Hand-operated cable reels - A.C., three-phase A.C. and D.C.

NF C28-913/IN1:2007 磁性材料.用单片测试计法测量电气薄钢板和电气钢带磁性的方法

Magnetic materials - Methods of measurement of the magnetic properties of electrical sheet and strip by means of a single sheet tester.

CSA C22.2 No.188-04 UPD 2-2007 线夹

Splicing wire connectors

Serre-Fils

BS EN 50397-1:2006 交流额定电压大于1kV和小于36kV的高架电力线和相关配件用绝缘导线.第1部分:绝缘导线

This Part 1 contains the requirements for covered conductors with or without integrated longitudinal watertightness and/or semi-conductive conductor screen for applications in overhead lines with rated voltages U above 1 kV a.c. and not exceeding 36 kV a.c.

Covered conductors for overhead lines and the related accessories for rated voltages above 1 kV a.c. and not exceeding 36 kV a.c. - Part 1: Covered conductors

ASTM B267-07 线绕电阻器用电阻丝的标准规范

1.1 This specification covers round wire and ribbon with controlled electrical properties for use in wire-wound resistance units and similar applications, but not for use as electrical heating elements.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Wire for Use In Wire-Wound Resistors

ASTM B603-07 电热元件用拉制或轧制铁-铬-铝合金的标准规范

1.1 This specification covers annealed, drawn, or rolled shapes for electrical heating and resistance purposes of alloys consisting mainly of iron, chromium, and aluminum as detailed in .1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Drawn or Rolled Iron-Chromium-Aluminum Alloys for Electrical Heating Elements

ASTM B114-07 分流器与精密电阻器用薄板材料温度-电阻常数的标准试验方法

This test method covers the determination of the change of resistance with temperature for precision resistors and shunts made from sheet materials. Materials normally used in the temperature range from 0 to 80°C may be tested using this test method.1.1 This test method covers the determination of the change of resistance with temperature of sheet materials used for shunts and precision resistors for electrical apparatus. It is applicable to materials normally used in the temperature range of from 0 to 80176;C.1.2 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units may be approximate.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Temperature-Resistance Constants of Sheet Materials for Shunts and Precision Resistors

ASTM B63-07 金属传导电阻和接触材料的电阻系数用标准试验方法

In the case of materials for resistors and heating elements, a knowledge of resistivity is important in determining whether wire or strip of a specified area of cross section and length will have a required resistance. It serves as one basis for the selection of materials for specific applications and its measurement is a necessary acceptance test for resistance materials. In the case of materials for electrical contacts, the measurement of resistivity can serve as a test for uniformity of materials of nominally the same composition and structure.1.1 This test method covers the determination, to a precision of 2 %, of the electrical resistivity of materials used in resistors, heating elements, and electrical contacts, as well as products of powder metallurgy processes which are used for other purposes. Note 1 - For determining the resistivity of electrical conductors, see Test Method B 193.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Resistivity of Metallically Conducting Resistance and Contact Materials

ASTM B77-07 电阻合金的热电功率用标准试验方法

The purpose of this method is to determine the suitability of different metals for use in resistance apparatus in which a low thermoelectric power is desired. As most electric circuits are largely composed of copper, the thermoelectric power of a resistance metal will generally be measured against copper.1.1 This test method covers the determination of the thermoelectric power of a metal or alloy with respect to copper when the temperatures of the junctions lie between 0 and 100C.1.2 The values stated in inch-pound units are the preferred unit. The values in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Thermoelectric Power of Electrical-Resistance Alloys

ASTM B63-07(2013) 金属传导电阻和接触材料的电阻系数的标准试验方法

4.1 In the case of materials for resistors and heating elements, a knowledge of resistivity is important in determining whether wire or strip of a specified area of cross section and length will have a required resistance. It serves as one basis for the selection of materials for specific applications and its measurement is a necessary acceptance test for resistance materials. 4.2 In the case of materials for electrical contacts, the measurement of resistivity can serve as a test for uniformity of materials of nominally the same composition and structure. 1.1 This test method covers the determination, to a precision of 28201;%, of the electrical resistivity of materials used in resistors, heating elements, and electrical contacts, as well as products of powder metallurgy processes which are used for other purposes. Note 1—For determining the resistivity of electrical conductors, see Test Method B193. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Resistivity of Metallically Conducting Resistance and Contact Materials

KS C 4532-2006 普通直流螺线管

이 규격은 직류 150 V 이하의 전기 회로에서 각종 기구의 조작에 사용하는 일반용 직류

DC solenoids for general purpose