K11 裸电线 标准查询与下载

WJ 71-2006 测压铜柱用铜线规范

Specification for copper wires for pressure measuring copper columns

ASTM B701/B701M-06 同芯绞捻自阻钢芯加强铝导线(ACSR/SD)的标准规范

1.1 This specification covers concentric-lay-stranded self-damping aluminum conductor, steel-reinforced (ACSR/SD), and its component wires for use as overhead electrical conductors (Explanatory Note 1 and 2).1.2 The values stated in inch-pound or SI units are to be regarded separately as standard. Each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the specification. For conductor sizes designated by AWG or kcmil, the requirements in SI units have been numerically converted from corresponding values stated or derived in inch-pound units. For conductor sizes designated by SI units only, the requirements are stated or derived in SI units.1.2.1 For density, resistivity, and temperature, the values stated in SI units are to be regarded as standard.Note 1ACSR/SD is designed to control aeolian vibration by integral damping. The conductors consist of a central core of a round steel wire or wires surrounded by two layers of trapezoidal aluminum 1350-H19 wires or two layers of trapezoidal aluminum 1350-H19 wires and one layer of round aluminum 1350-H19 wires (Fig. 1). The trapezoidal-wire layers are separated from each other and from the steel core by two small annular gaps that provide the conductors self-damping characteristics. The round aluminum wires are in tight layer contact between themselves and the underlying trapezoidal wire layer. Different strandings of the same size of conductor are identified by type, which is the approximate ratio of steel area to aluminum area, expressed in percent (Table 1 and Table 2).Note 2The aluminum and temper designations conform to ANSI Standard H 35.1. Aluminum 1350 corresponds to UNS A91350 in accordance with Practice E 527.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Concentric-Lay-Stranded Self-Damping Aluminum Conductors, Steel Reinforced (ACSR/SD)

IEEE 738-2006 架空裸导线载流量和温度的关系计算

A method of calculating the current-temperature relationship of bare overhead lines, given the weather conditions, is presented. Along with a mathematical method, sources of the values to be used in the calculation are indicated. This standard does not undertake to list actual temperature-ampacity relationships for a large number of conductors, but rather provides a standard method of doing such calculations.

Standard for Calculating the Current-Temperature of Bare Overhead Conductors

KS C IEC 60114:2005 热处理型铝镁硅系铝合金母线材料的建议

알루미늄-마그네슘-실리콘형의 열처리 알루미늄 합금 부스바 재료의 일반 요구 사항을 규정한다

Recommendation for heat-treated aluminium alloy busbar material of the aluminium-magnesium-silicon type

CSA C22.2 No.210-05-2005 电器引接线材料产品.第2版.代替CAN/CSA-C22.2 No.210.2-M90.第1次修订

This standard applies to single-or multiple-conductor,round,flat,or coiled appliance wiring material proudcts classified as follows

Appliance wiring material products Second Edition; Update No 1

BS EN 60228:2005 绝缘电缆导线

This International Standard specifies the nominal cross-sectional areas, in the range 0,5 mm to 2 500 mm, for conductors in electric power cables and cords of a wide range of types. Requirements for numbers and sizes of wires and resistance values are also included. These conductors include solid and stranded copper, aluminium and aluminium alloy conductors in cables for fixed installations and flexible copper conductors. The standard does not apply to conductors for telecommunication purposes. The applicability of this standard to a particular type of cable is as specified in the standard for the type of cable. Unless indicated to the contrary in a particular clause, this standard relates to the conductors in the finished cable and not to the conductor as made or supplied for inclusion into a cable. Informative annexes are included giving supplementary information covering temperature correction factors for resistance measurement (Annex 6) and dimensional limits of circular conductors (Annex C).

Conductors of insulated cables

ASTM B189-05(2010) 电气用铅涂覆和铅合金涂覆软铜线的标准规格

1.1 This specification covers lead-coated and lead-alloy-coated, round, soft or annealed copper wire for electrical purposes. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. The SI values for density and resistivity are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The hazard statement applies only to Section 6 of this specification.

Standard Specification for Lead-Coated and Lead-Alloy-Coated Soft Copper Wire for Electrical Purposes

ASTM B800-05(2011) 8000系列铝合金电气线材的退火和中温回火标准规格

1.1 This specification covers 8000 series aluminum alloys fabricated into round wires in annealed or intermediate tempers suitable for stranding into conductors or for solid single conductors, usually to be insulated. 1.2 The SI values for resistivity are regarded as standard. For all other properties, the inch-pound units are regarded as standard and the SI units may be approximate. Note 18212;Aluminum alloys capable of meeting the requirements of this specification are listed in Table 1. Note 28212;The alloy and temper designations conform to ANSI H35.1. Unified Numbering System alloy designations are listed in Table 1 in accordance with Practice E527. Note 38212;Certain aluminum alloys may be subject to patent rights. U.S. patents numbers are shown in Table 1. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. TABLE 1 Aluminum Alloys Alloy DesignationU.S. Patent Number ANSI-H35.1 UNS 8017A98017... 8030A98030 3711339 8076 A98076 3697260 8130 A98130 ... 8176 A98176 RE 28419 RE 30465 8177A98177 ...

Standard Specification for 8000 Series Aluminum Alloy Wire for Electrical PurposesAnnealed and Intermediate Tempers

ASTM B711-05 同心绞捻铝合金钢芯导线(AACSR)(6201)的标准规范

1.1 This specification covers concentric-lay-stranded conductors made from round aluminum-alloy 6201-T81 hard: solution heat treated, cold worked, and then artificially aged wire and round zinc-coated, Zn-5Al-MM coated, aluminum-coated, or aluminum-clad steel core wire for use as overhead electric conductors (Explanatory Note 0 and Note 0). The alloy and temper designations conform to ANSI H35.1. Aluminum alloy 6201 corresponds to Unified Numbering System alloy A96201 in accordance with Practice E 527.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Concentric-Lay-Stranded Aluminum-Alloy Conductors, Steel Reinforced (AACSR) (6201)

ASTM B189-05(2015) 电工用铅涂覆和铅合金涂覆软铜线的标准规格

1.1 This specification covers lead-coated and lead-alloy-coated, round, soft or annealed copper wire for electrical purposes. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. The SI values for density and resistivity are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The hazard statement applies only to Section 6 of this specification.

Standard Specification for Lead-Coated and Lead-Alloy-Coated Soft Copper Wire for Electrical Purposes

CSA C22.2 No.188-04-2004 绞接接线器.第1次修订:2006年8月

Revisions of this Standard will be made by issuing revised or additional pages bearing their date of issue. A UL Standard is current only if it incorporates the most recently adopted revisions, all of which are itemized on the transmittal notice that ac

Splicing wire connectors Second Edition; Update No.1: August 2006; Update No.2: March 2007; Update No.3: January 2010; Update No.4: February 2010

ANSI/NECA 102-2004 安装铝导管

This standard describes installation procedures for aluminum rigid metal conduit (RMC).

Installing Aluminum Conduits

JIS C 2806 ERRATUM 2:2004 勘误

ERRATUM

ASTM B401-04(2010) 致密圆形钢芯加强同轴绞捻铝导线(ACSR/COMP)标准规格

1.1 This specification covers compact round concentric-lay-stranded conductors made from aluminum 1350-H19 (extra hard) wires and round zinc-coated, aluminum-coated, or aluminum-clad steel core wires usually used in overhead lines. These conductors shall be constructed with one steel core wire surrounded by one or more layers of helically-laid compacted or otherwise shaped aluminum wires (Explanatory Note 1 and Note 2). 1.2 Compact ACSR covered by this specification has five types of steel core wire which are designated by abbreviations as follows (Explanatory Note 2). 1.2.1 ACSR/GA/COMP8212;Compact ACSR using Class A zinc-coated steel wire, 1.2.2 ACSR/GB/COMP8212;Compact ACSR using Class B zinc-coated steel wire, 1.2.3 ACSR/GC/COMP8212;Compact ACSR using Class C zinc-coated steel wire, 1.2.4 ACSR/AZ/COMP8212;Compact ACSR using aluminum-coated (aluminized) steel wire, and 1.2.5 ACSR/AW/COMP8212;Compact ACSR using aluminum-clad steel wire. 1.3 The SI values of density and resistivity are to be regarded as standard. For all other properties the inch-pound values are to be regarded as standard and the SI units may be approximate. Note 18212;Prior to 1975, aluminum 1350 was designated as EC aluminum. Note 28212;The aluminum and temper designations conform to ANSI H35.1. Aluminum 1350 corresponds to Unified Numbering System A91350 in accordance with Practice E527.

Standard Specification for Compact Round Concentric-Lay-Stranded Aluminum Conductors, Steel-Reinforced (ACSR/COMP)

ASTM B496-04(2010)e1 密实的圆形同心绞捻铜导线的标准规格

1.1 This specification covers bare compact round concentric-lay-stranded conductors made from uncoated round copper wires for general use for electrical purposes. These conductors shall be constructed with a central core surrounded by one or more layers of helically laid compacted wires (Explanatory Note 1 and Note 2). 1.2 The values stated in inch-pound or SI units are to be regarded separately as standard. The values in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.2.1 For density, resistivity, and temperature, the values stated in SI units are to be regarded as standard.

Standard Specification for Compact Round Concentric-Lay-Stranded Copper Conductors

ASTM B835-04(2009) 使用单输入线路结构的压缩圆铜绞线的标准规范

1.1 This specification covers bare compact round stranded conductors made from uncoated copper wires of a single input wire (SIW) diameter for general use in covered or insulated electrical wires or cables. These conductors shall be constructed with one or more layers of helically laid compacted wires (Explanatory Note 1, Note 2, and Note 3). 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.2.1 For density, resistivity and temperature, the values stated in SI units are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Compact Round Stranded Copper Conductors Using Single Input Wire Construction

ASTM B496-04 密实的圆形同心绞捻铜导线标准规范

1.1 This specification covers bare compact round concentric-lay-stranded conductors made from uncoated round copper wires for general use for electrical purposes. These conductors shall be constructed with a central core surrounded by one or more layers of helically laid compacted wires (Explanatory and Note 0).1.2 The values stated in inch-pound or SI units are to be regarded separately as standard. The values in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.1.2.1 For density, resistivity, and temperature, the values stated in SI units are to be regarded as standard.

Standard Specification for Compact Round Concentric-Lay-Stranded Copper Conductors

ASTM B229-04 芯线扭绞的铜与包铜组合钢导线标准规范

1.1 This specification covers concentric-lay-stranded conductors made from uncoated hard-drawn round copper wires in combination with hard-drawn round copper-clad steel wires, for general use as overhead electrical conductors.1.2 For the purpose of this specification, conductors are classified under the following type designations (see Fig 1): Type AType GType CType JType DType KType EType NType EKType PType FType V1.3 The SI values for density are regarded as the standard. For all other properties the inch-pound values are to be regarded as standard and the SI units may be approximate.

Standard Specification for Concentric-Lay-Stranded Copper and Copper-Clad Steel Composite Conductors

ASTM B566-04a(2016) 铜包铝线的标准规格

1.1 This specification covers bare round copper-clad aluminum wire for electrical applications. 1.2 Four classes of copper-clad aluminum wire are covered as follows: Class 10A—Nominal 10 volume % copper, annealed. Class 15A—Nominal 15 volume % copper, annealed. Class 10H—Nominal 10 volume % copper, hard-drawn. Class 15H—Nominal 15 volume % copper, hard-drawn. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3.1 Exception—The values stated in SI units for resistivity and density are to be regarded as standard.

Standard Specification for Copper-Clad Aluminum Wire

ASTM B399/B399M-04(2015) 同芯式绞合铝合金6201-T81导线的标准规格

1.1 This specification covers concentric-lay-stranded conductors, made from round aluminum-alloy 6201-T81 (hard: solution heat-treated, cold worked, and then artificially aged) wires, for use for electrical purposes. These conductors shall be constructed with a central core surrounded by one or more layers of helically laid wires (Explanatory Notes 1 and 2). Note 1: The aluminum alloy and temper designations conform to ANSI H35.1/H35.1[M]. Aluminum-alloy 6201 corresponds to Unified Numbering System alloy A96201 in accordance with Practice E527. 1.2 The values stated in inch-pound units or SI units are to be regarded separately as standard. The values in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.2.1 For density, resistivity and temperature, the values stated in SI units are to be regarded as standard.

Standard Specification for Concentric-Lay-Stranded Aluminum-Alloy 6201-T81 Conductors