K11 裸电线 标准查询与下载

IEEE 605/INT 1-2011 空气绝缘变电站母线设计用IEEE Std 605™-2008标准指南的IEEE标准解释

This is an interpretation of IEEE Std 605-2008.

IEEE Standards Interpretation for IEEE Std 605™-2008 IEEE Guide for Bus Design in Air Insulated Substations

BS EN 61788-11:2011 超导电性.残余电阻比测量.Nb3Sn复合超导体的残余电阻比

Superconductivity. Residual resistance ratio Measurement. Residual resistance ratio of Nb3Sn composite superconductors

SAE AS81822/7A-2011 锡涂层固体导体带聚酰亚胺绝缘护套的挤压聚氯乙烯(PVE)绝缘无焊包装电线

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist.

Wire, Electrical, Solderless Wrap, Polyimide Jacket Over Extruded Polyvinyl Chloride (PVE) Insulation, Tin Coated Solid Conductor

JB/T 6313.1-2011 电工铜编织线.第1部分：一般规定

JB/T 6313的本部分规定了电工铜编织线的代号、产品标记及示例、技术要求、检验规则及包装、运输和贮存。 本部分适用于输配电用电气装置及电子电气设备或元件连接用的电工铜编织线。

Braided copper wires for electrical purposes.Part 1: General

JB/T 6313.2-2011 电工铜编织线.第2部分：斜纹编织线(套)

JB/T 6313的本部分规定了斜纹编织线（套）的型号、规格、技术要求及检验规则。 本部分适用于斜纹编织线（套）[包括斜纹铜编织线和斜纹镀锡铜编织线（套）]。

Braided copper wires for electrical purposes.Part 2: Diagonal braided wires

JB/T 6313.3-2011 电工铜编织线.第3部分：直纹编织线

JB/T 6313的本部分规定了直纹铜编织线的型号、规格、技术要求及检验规则。 本部分适用于直纹铜编织线。

Braided copper wires for electrical purposes.Part 3: Plain braided wires

ANSI/ICEA S-89-648-2011 架空线标准

Standard for Aerial Service Wire

ASTM B8-11 硬的,中等硬的或软的同心绞捻铜导线标准规格

1.1 This specification covers bare concentric-lay-stranded conductors made from round copper wires, either uncoated or coated with tin, lead, or lead alloy for general use for electrical purposes. These conductors shall be constructed with a central core surrounded by one or more layers of helically laid wires. Note 18212;This specification also permits conductors for use as covered or insulated electrical conductors. Note 28212;Sealed conductors, that are intended to prevent longitudinal water propagation and are further covered/insulated, are also permitted within the guidelines of this specification. 1.2 For the purposes of this specification, conductors are classified as follows (Explanatory Note 1 and Note 2): 1.2.1 Class AA8212;For bare conductors usually used in overhead lines. 1.2.2 Class A8212;For conductors to be covered with weather-resistant (weather-proof), slow-burning materials, and for bare conductors where greater flexibility than is afforded by Class AA is required. 1.2.3 Class B8212;For conductors to be insulated with various materials such as rubber, paper, varnished cloth, and so forth, and for the conductors indicated under Class A where greater flexibility is required. 1.2.4 Class C and Class D8212;For conductors where greater flexibility is required than is provided by Class B conductors. 1.3 The SI values for density are regarded as the standard. For all other properties, the inch-pound values are to be regarded as standard and the SI units may be approximate.

Standard Specification for Concentric-Lay-Stranded Copper Conductors, Hard, Medium-Hard, or Soft

ASTM B857-11 包钢加强的(ACSS/TW)成型密实同心绞捻铝导线的标准规范

1.1 This specification covers shaped wire compact concentric-lay-stranded aluminum conductors, steel supported (ACSS/TW) for use as overhead electrical conductors (see Explanatory Note 1). 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.2.1 Exceptions8212;For conductor sizes designated by AWG or kcmil sizes, the requirements in SI units are numerically converted from the corresponding requirements in inch-pound units. For conductor sizes designation by AWG or kcmil, the requirements in SI units have been numerically converted from corresponding values stated or derived in inch-pound units. For conductor sizes designated by SI units only, the requirements are stated or derived in SI units. For density, resistivity, and temperature, the values stated in SI units are to be regarded as standard. 1.3 ACSS/TW is designed to increase the aluminum area for a given diameter of conductor by the use of trapezoidal shaped wires (TW). The conductors consist of a central core of round steel wire(s) surrounded by two or more layers of trapezoidal aluminum 1350-0 wires. Different strandings of the same size of conductor are identified by type, which is the approximate ratio of steel area to aluminum area expressed in percent (see Table 1, Table 2, and Table 3). For the purpose of this specification, the sizes listed in Table 1 and Table 2 are tabulated on the basis of the finished conductor having an area or outside diameter equal to that of specified sizes of standard ACSR, ACSS, and ACSR/TW so as to facilitate conductor selection.

Standard Specification for Shaped Wire Compact Concentric-Lay-Stranded Aluminum Conductors, Coated-Steel Supported (ACSS/TW)

ASTM B228-11a(2016) 同心式绞合铜包钢导体的标准规格

1.1 This specification covers bare concentric-lay-stranded conductors made from bare round copper-clad steel wires for general use for electrical purposes. 1.2 For the purpose of this specification, conductors are classified as follows: Grade 40 HS, Grade 30 HS, Grade 30 EHS, Grade 40 DSA, and Grade 30 DSA. The grades covered by this specification correspond to the following commercial designations: Grade 40 HS, High Strength, 40% Conductivity, Hard Drawn Grade 30 HS, High Strength, 30% Conductivity, Hard Drawn Grade 30 EHS, Extra High Strength, 30% Conductivity, Hard Drawn Grade 40 DSA, 40% Conductivity, Dead Soft Annealed Grade 30 DSA, 30% Conductivity, Dead Soft Annealed 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Concentric-Lay-Stranded Copper-Clad Steel Conductors

ASTM B99/B99M-11 一般用途铜硅合金电线的标准规格

1.1 This specification establishes the requirements for round, rectangular, and square wire for general applications other than for electrical transmission cable. The alloys involved are UNS Nos. C65100 and C65500. 1.2 Units8212;Values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

Standard Specification for Copper-Silicon Alloy Wire for General Applications

ASTM B8-11(2017) 硬的, 中等硬的或软的同心绞捻铜导线的标准规格

1.1 This specification covers bare concentric-lay-stranded conductors made from round copper wires, either uncoated or coated with tin, lead, or lead alloy for general use for electrical purposes. These conductors shall be constructed with a central core surrounded by one or more layers of helically laid wires. Note 1: This specification also permits conductors for use as covered or insulated electrical conductors. Note 2: Sealed conductors, that are intended to prevent longitudinal water propagation and are further covered/insulated, are also permitted within the guidelines of this specification. 1.2 For the purposes of this specification, conductors are classified as follows (Explanatory Note 1 and Note 2): 1.2.1 Class AA—For bare conductors usually used in overhead lines. 1.2.2 Class A—For conductors to be covered with weather-resistant (weather-proof), slow-burning materials, and for bare conductors where greater flexibility than is afforded by Class AA is required. 1.2.3 Class B—For conductors to be insulated with various materials such as rubber, paper, varnished cloth, and so forth, and for the conductors indicated under Class A where greater flexibility is required. 1.2.4 Class C and Class D—For conductors where greater flexibility is required than is provided by Class B conductors. 1.3 The SI values for density are regarded as the standard. For all other properties, the inch-pound values are to be regarded as standard and the SI units may be approximate. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Concentric-Lay-Stranded Copper Conductors, Hard, Medium-Hard, or Soft

ASTM B232/B232M-11 钢涂层强化(ACSR)同心绞捻铝绞线的标准规格

1.1 This specification covers concentric-lay-stranded conductors made from round aluminum 1350-H19 (extra hard) wires and round, coated steel core wire(s) for use as overhead electrical conductors (Explanatory Note 1 and Explanatory Note 2). 1.2 ACSR covered by this specification has nine types of coated steel core wire which are designated by abbreviations as follows (Explanatory Note 2): 1.2.1 ACSR/GA or ACSR/GA28212;ACSR using Class A zinc-coated steel wire, 1.2.2 ACSR/GC or ACSR/GC28212;ACSR using Class C zinc-coated steel wire, 1.2.3 ACSR/MA or ACSR/MA28212;ACSR using Class A Zn-5A1-MM coated steel wire, 1.2.4 ACSR/HS or ACSR/GA38212;ACSR using Class A zinc-coated high-strength steel wires, 1.2.5 ACSR/MS or ACSR/MA38212;ACSR using Class A Zn-5A1-MM coated high-strength steel wires, 1.2.6 ACSR/GA48212;ACSR using Class A zinc-coated extra-high-strength steel wires, 1.2.7 ACSR/MA48212;ACSR using Class A Zn-5A1-MM coated extra-high-strength steel wires, 1.2.8 ACSR/GA58212;ACSR using Class A zinc-coated ultra-high-strength steel wires, 1.2.9 ACSR/MA58212;ACSR using Class A Zn-5Al-MM coated ultra-high-strength steel wires. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Coated-Steel Reinforced (ACSR)

ASTM B856-11 镀覆钢支持的同心铺设铝绞线标准规格(ACSS)

1.1 This specification covers round wire concentric-lay-stranded aluminum conductors, steel supported (ACSS) for use as overhead electrical conductors (see Explanatory Note 1). 1.2 The values stated in inch-pound or SI units are to be regarded separately as standard. Each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. For conductor sizes designated by AWG or kcmil sizes, the requirements in SI units are numerically converted from the corresponding requirements in inch-pound units. For conductor sizes designation by AWG or kcmil, the requirements in SI units have been numerically converted from corresponding values stated or derived in inch-pound units. For conductor sizes designated by SI units only, the requirements are stated or derived in SI units. 1.2.1 For density, resistivity and temperature, the values stated in SI units are to be regarded as standard.

Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Coated Steel Supported (ACSS)

ASTM B226-11 有心的环形芯线扭绞的铜绞线标准规格

1.1 This specification covers cored, annular, concentric-lay-stranded conductors made from round soft copper wires, either uncoated or coated with tin for use as electrical conductors (Explanatory Note 1 and Note 2). 1.2 The constructions prescribed herein are suitable for bare conductors, or for conductors to be covered with weather-resistant (weather-proof) material, or for conductors to be insulated with rubber, varnished cloth, or impregnated paper, except types such as “oil-filled” or “gas-filled” (Explanatory Note 3). 1.3 Cored, annular conductor constructions not included in this specification shall be specifically agreed upon between the manufacturer and the purchaser when placing the order. 1.4 These constructions are not recommended for use as electric furnace leads where great flexibility is required and special conductor designs are indicated in consideration of the particular service requirements. 1.5 The SI values for density are regarded as the standard. For all other properties the inch-pound values are to be regarded as standard and the SI units may be approximate.

Standard Specification for Cored, Annular, Concentric-Lay-Stranded Copper Conductors

ASTM B228-11 芯线扭绞的包铜钢导线标准规格

1.1 This specification covers bare concentric-lay-stranded conductors made from bare round copper-clad steel wires for general use for electrical purposes. 1.2 For the purpose of this specification, conductors are classified as follows: Grade 40 HS, Grade 30 HS, and Grade 30 EHS. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Concentric-Lay-Stranded Copper-Clad Steel Conductors

ASTM B228-11a 同心莱链铜包钢导线的标准规范

1.1 This specification covers bare concentric-lay-stranded conductors made from bare round copper-clad steel wires for general use for electrical purposes. 1.2 For the purpose of this specification, conductors are classified as follows: Grade 40 HS, Grade 30 HS, and Grade 30 EHS. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Concentric-Lay-Stranded Copper-Clad Steel Conductors

ASTM B231/B231M-11 同心绞捻铝1350导线的标准规格

1.1 This specification covers aluminum 1350-H19 (extra hard), 1350-H16 or -H26 (¾ hard), 1350-H14 or -H24 (½ hard), and 1350-H142 or -H242 (½ hard), bare concentric-lay-stranded conductors constructed with a straight round central wire surrounded by one or more layers of helically layed wires. The conductors are for general use for electrical purposes (Explanatory Note 1 and Note 2). 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.2.1 For density, resistivity and temperature, the values stated in SI units are to be regarded as standard. Note 18212;Prior to 1975, aluminum 1350 was designated as EC aluminum. Note 28212;The aluminum and temper designations conform to ANSI Standard H35.1/H35.1M. Aluminum 1350 corresponds to Unified Numbering System A91350 in accordance with Practice E527. Note 38212;Sealed conductors that are intended to prevent longitudinal water propagation and are further covered/insulated are also permitted within the guidelines of this specification.

Standard Specification for Concentric-Lay-Stranded Aluminum 1350 Conductors

ASTM B976-11 复合加强型(ACCR)铝导体纤维增强铝基复合(AMC)芯导线标准规格

1.1 This specification covers fiber reinforced, aluminum matrix composite core wire used for mechanical reinforcement in the manufacture of aluminum conductor, composite reinforced (ACCR). This wire consists of continuous filament fibers of aluminum oxide in a matrix of aluminum. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.2.1 Exception8212;Some non-standard SI units provided for information only do not appear in brackets. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Fiber Reinforced Aluminum Matrix Composite (AMC) Core Wire for Aluminum Conductors, Composite Reinforced (ACCR)

ASTM B226-11(2016) 有心的圆形同心绞捻铜导线标准规范

1.1 This specification covers cored, annular, concentric-lay-stranded conductors made from round soft copper wires, either uncoated or coated with tin for use as electrical conductors (Explanatory Note 1 and Note 2). 1.2 The constructions prescribed herein are suitable for bare conductors, or for conductors to be covered with weather-resistant (weather-proof) material, or for conductors to be insulated with rubber, varnished cloth, or impregnated paper, except types such as “oil-filled” or “gas-filled” (Explanatory Note 3). 1.3 Cored, annular conductor constructions not included in this specification shall be specifically agreed upon between the manufacturer and the purchaser when placing the order. 1.4 These constructions are not recommended for use as electric furnace leads where great flexibility is required and special conductor designs are indicated in consideration of the particular service requirements. 1.5 The SI values for density are regarded as the standard. For all other properties the inch-pound values are to be regarded as standard and the SI units may be approximate.

Standard Specification for Cored, Annular, Concentric-Lay-Stranded Copper Conductors