共找到 282 条与 电力电容器 相关的标准,共 19 页
本标准为电气设备抗干扰特性的基本测量方法。 本标准适用于: a.测量电气设备的电磁敏感度。 b.考核电气设备的抗干扰性能是否符合产品技术条件规定的电磁敏感度界限值。 在符合本标准要求的前提下,各类电气设备可制订相应的抗干扰特性测量方法和规定需要进行的测试项目。
General methods of measurement of immunity to interference for electrical equipment
本文件规定了高压并联电容器装置放电线圈更换、投运、使用条件、运行维护、试验、异常处理、退运、替换等要求。 本文件适用于50Hz 、6kV~66kV高压并联电容器装置用单相全密封油浸式、干式的放电线圈。充气式的放电线圈可参照执行。
Capacitor discharge coil operation and maintenance procedures
本文件规定了交流耦合电容器及电容分压器的术语和定义、使用条件、技术要求、试验和标志。 本文件适用于额定交流电压1000 V以上,接于线与地之间,低压端子永久接地或接电力线路载波(PLC)附件、谐波滤波器调谐器件的交流单相耦合电容器以及用于电压互感器制造的交流单相电容分压器及其他类似用途的电容器。 注1:对电力线路载波(PLC)系统用的载波附件的要求参照GB/T 19749.2,对调谐单元的要求参照GB/T 19749.3,对于电压互感器制造用的交流单相电容分压器参照GB/T 19749.4。 注2:对大容量框架式交流PLC电容器的要求参照GB/T 31954。
Technical conditions for use of AC coupling capacitors and capacitive voltage dividers
本文件规定了高压并联电容器装置放电线圈的术语和定义、使用条件、技术要求、试验方法、检验规则、标志、包装、运输和储存。 本文件适用于额定频率50 Hz、电压等级6 kV~66 kV高压并联电容器装置所配用的单相全密封油浸式和干式放电线圈。放电线圈高压绕组与高压井联电容器组并联连接,使电容器从电力系统切除后在规定时间内将电容器剩余电压降至要求值。当放电线圈有二次绕组时,可兼作电压测量和为继电保护提供电压信号。
Technical conditions for use of discharge coils for high-voltage parallel capacitors
本文件规定了柔性直流换流器用直流电容器的使用条件、技术性能、设计、试验、标志、包装、贮存、运输和验收等方面的技术要求。 本文件适用于±800 kV及以下柔性高压直流输电系统中,安装在换流阀上与可控的电力电子元器件组合成功率模块子单元的直流电容器。电压1000V以下的柔性直流换流器用直流电容器可参照执行。
Technical Guidelines for DC Capacitors Used in Flexible DC Converters
本文件规定了直流输电用直流耦合电容器及电容分压器的使用条件、技术性能、设计要求、试验方法等。 本文件适用于额定电压±500 kV及以上直流输电系统,接于线与地之间、低压端子永久接地或与频率为30kHz~500kHz的电力线路载波(PLC)设备连接的直流耦合电容器以及直流单相电容分压器。
Technical conditions for DC coupling capacitors and capacitive voltage dividers for DC transmission
Terminology of reactive power compensation and harmonic control devices
Shunt power capacitors of the self-healing type for AC systems having a rated voltage above 1 000 V
Round and oval aluminum casings for power capacitors
Insert-type metal explosion-proof cover assembly for power capacitors
Insert-type metal explosion-proof cover assembly for power capacitors
Round and oval aluminum casings for power capacitors
Technical specifications for supercapacitors used in wind turbine pitch systems
Technical Guidelines for AC Filter Capacitors Used in Power Systems
This International Standard is applicable to low-voltage AC shunt capacitor banks intended to be used for power factor correction purposes, possibly equipped with a built-in switchgear and controlgear apparatus capable of connecting to or disconnecting from the mains part(s) of the bank with the aim to correct its power factor. Low-voltage power factor correction banks if not otherwise indicated hereinafter and where applicable comply with the requirements of IEC 61439-1 and IEC 61439-2.
Power capacitors - Low-voltage power factor correction banks
Grading capacitors for high-voltage alternating current circuit-breakers - Part 1: General (IEC 62146-1:2013 + A1:2016); German version EN 62146-1:2014 + A1:2016
Series capacitors for power systems - Part 3: Internal fuses (IEC 60143-3:2015); German version EN 60143-3:2015
Calibration specification for capacitive equipment on-line monitoring device
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号