L38 电子束管 标准查询与下载

SJ/T 11461.1.1-2013 有机发光二极管显示器 第1-1部分:总规范

本部分规定了有机发光二极管(OLED)显示器件的通用要求。它规定了适用于IECQ-CECC体系的质量评定通用程序,并给出了光电特性测量、环境和机械试验以及耐久性试验的通用规则。

Organic light emitting diode (OLED) displays.Part 1-1: Generic specifications

SJ/T 11461.5.1-2013 有机发光二极管显示器 第5-1部分:环境试验方法

本部分给出了在规定的环境条件下,评价有机发光二极管显示模块(以下简称OLED显示器模块)工作和贮存时的环境适应性的试验方法。

Organic light emitting diode (OLED) displays.Part 5-1: Environmental testing methods

SJ/T 11458-2013 液晶显示背光组件用LED性能规范

本规范规定了液晶显示背光组件用发光二极管(以下简称“LED”)的性能要求、检验方法、检验规则。本规范适用于液晶显示背光组件用非空腔封装白光LED。

LED for liquid crystal display backlight unit performance specification

SJ/T 11455-2013 示波管和指示管的测试方法

本标准规定了示波管和指示管(以下简称电子管)测试方法。本标准适用于示波管和指示管光电参数的测试。

Methods measurement of oscilloscope tubes and indicator tubes

SJ/T 11459.2.2.4-2013 液晶显示器件 第2-2-4部分:手机用彩色矩阵液晶显示模块详细规范

本规范适用于:手机用透射式有源彩色矩阵液晶显示模块。

Liquid crystal display devices.Part 2-2-4: Matrix colour LCD modules for mobile phone.Detail specification

SJ/T 11459.2.2.2-2013 液晶显示器件 第2-2-2部分:显示器用彩色矩阵液晶显示模块详细规范

本部分适用于:显示器用CCFL背光彩色矩阵液晶显示模块。

Liquid crystal display devices.Part 2-2-2: Matrix colour LCD modules for monitor.Detail specification

SJ/T 11459.2.2.1-2013 液晶显示器件 第2-2-1部分:车载用彩色矩阵液晶显示模块详细规范

本部分适用于:车载用LED背光彩色有源矩阵液晶显示模块。

Liquid crystal display devices.Part 2-2-1: Matrix colour LCD module for automotive applications.Detail specification

SJ/T 11459.2.2.3-2013 液晶显示器件 第2-2-3部分:便携式计算机用彩色矩阵液晶显示模块详细规范

本规范适用于:便携式计算机用LED背光彩色矩阵液晶显示模块。

Liquid crystal display devices.Part 2-2-3: Matrix colour LCD modules for Notebook PC.Detail specification

BS EN 62341-5-2:2013 有机发光二极管(OLED)显示器.机械耐力测试方法

Organic light emitting diode (OLED) displays. Mechanical endurance testing methods

IEC 62679-3-2:2013 电子纸显示器.第3-2部分:测量方法.电-光

This part of IEC 62679 series is restricted to electronic paper display modules using either segment@ passive@ or active matrix@ and either monochromatic@ or colour type displays. In order to achieve a useful and uniform description of the performance of these devices@ specifications for commonly accepted relevant parameters are put forward. The purpose of this part of IEC 62679 series is to indicate and list the procedure-dependent parameters and to prescribe the specific methods and conditions that are to be used for their uniform numerical determination.

Electronic paper display - Part 3-2: Measuring method - Electro-optical

BS EN 61747-2-1:2013 液晶显示设备. 无源矩阵单色液晶显示模块. 空白详细规范

Liquid crystal display devices. Passive matrix monochrome LCD modules. Blank detail specification

BS EN 61747-30-1:2012 液晶显示设备. 液晶显示模块的测量方法. 透射型

Liquid crystal display devices. Measuring methods for liquid crystal display modules. Transmissive type

IEC 61747-4:2012 液晶显示器.第4部分:液晶显示模块和屏.基本额定值和特性

This part of IEC 61747 describes the essential ratings and characteristics of LCD cells and passive matrix monochrome liquid crystal display modules. It does not apply to active matrix LCD cells nor to multicolour cells.

Liquid crystal display devices - Part 4: Liquid crystal display modules and cells - Essential ratings and characteristics

IEC 61988-4-2:2012 等离子体显示屏.第4-2部分:环境试验方法.面板强度

This part of IEC 61988 defines testing methods for evaluating mechanical characteristics of plasma display modules (PDP modules) in the following areas: a) Ball drop breaking strength of panels; b) Partial heating strength of panels.

Plasma Display Panels - Part 4-2: Environmental testing methods - Panel strength

GJB 3312A-2011 微波电子管通用规范

本规范规定了军用微波电子管的通用要求、质量保证规定和交货准备等。 本规范适用于行波管、速调管、磁控管、充气微波开关管（以下简称开关管）、前向波放大管和回旋管的研制、生产、检验和采购，其他微波电子管可参照执行。

General specification for microwave tubes

BS EN 61747-5-3:2010 液晶显示器.环境,耐受和机械性能试验方法.玻璃强度和可靠性

This part of IEC 61747 applies to commercially available liquid crystal displays (LCDs). This standard applies to all LCD types, including transmissive, reflective or transflective liquid crystal display (LCD) modules using either segment, passive or active matrix and achromatic or colour type LCDs that are equipped with their own integrated source of illumination or without their own source of illumination. The objective of this standard is to establish uniform requirements for accurate and reliable measurements of the following LCD parameters: a) quasistatic strength, b) quasistatic fatigue. The methods described in this standard apply to all sizes, small and large, liquid crystal displays.

Liquid crystal display devices - Environmental, endurance and mechanical test methods - Glass strength and reliability

BS EN 61988-5:2009 等离子显示器.通用规范

This generic specification for plasma display panels specifies general procedures for quality assessment to be used in the IECQ-CECC system and establishes general principles for describing and testing of electrical, optical, mechanical and environmental characteristics.

Plasma display panels - Generic specification

BS EN 61988-3-2:2009 等离子体显示板.接口.电气接口

This part of IEC 61988 defines the electrical interface of digital video data signals, synchronization signals and functional signals between the image processing board of the PDP set and the control board of the PDP module, and defines the description of the pin assignment of the connectors.

Plasma display panels - Interface - Electrical interface

BS EN 61988-2-3:2009 等离子体显示器.测量方法.图像质量.退化和缺陷

This part of IEC 61988 determines the measuring methods for defects and degradation of colour plasma display (PDP) module in the following areas: a) cell defects; b) image sticking; c) luminance lifetime.

Plasma display panels - Measuring methods - Image quality - Defects and degradation

IEC 61988-5:2009 等离子显示器.第5部分:通用规范

This generic specification for plasma display panels specifies general procedures for quality assessment to be used in the IECQ-CECC system and establishes general principles for describing and testing of electrical@ optical@ mechanical and environmental characteristics.

Plasma display panels - Part 5: Generic specification