L38 电子束管 标准查询与下载

SN/T 0810.1-1999 出口显示器安全要求检验规程

Rules for the inspection of safety requirements of monitor for export

SJ 20463/11-1999 31SS51Y7型指示管详细规范

Detail specification for type 31SS51Y7 indicator tube

ANSI/EIA 743:1999 单色显象管可使用屏幕尺寸

Usable Screen Dimensions for Monochrome Display Tubes

SJ/T 11198-1999 黑白显象管、单色显示管和电光源用玻管

本标准规定了黑白显象管、单色显示管和电光源用玻管的要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于黑白显象管、单色显示管用玻管和相应材质电光源用玻管。

Glass tubes for black and white picture tubes, monochrome display tubes and electric light sources

CEA-633.10-1999 EIA-600同一规范介绍

This standard is concerned with conformance of an implementation to the associated protocol specifications contained in EIA-600. A dual audience is expected for this standard. The first is laboratories that may be interested in acting as conformance testing agencies. Such agencies are tasked with converting these requirements into a hardware/software test system. The CEBus Industry Council (CIC) has been charged with protecting trade and service marks associated with EIA-600. As such, CIC manages the conformance testing process for the purpose of product certification. The second audience is the set of designers of EIA-600 compatible products. Any designer of compatible products should understand the importance of the tests described in this standard, as they relate to implementing EIA-600. The second group should read this standard while considering whether its hardware and/or software implementation is likely to pass the stated tests.

Introduction to EIA-600 Conformance Specification

ASTM E2023-99(2004) 中子射线照相敏感度显示器制造的标准操作规程

The only truly valid image quality indicator is a material or component, equivalent to the part being neutron radiographed, with a known standard discontinuity, inclusion, omission or flaw (reference standard comparison part). The SI is designed to substitute for the reference standard, providing qualitative information on hole and gap sensitivity in a single unit. Fabrication in accordance with this practice is vital for accurate and consistent measurements. This practice shall be followed for the fabrication of all SIs to be used with Method E 545 to determine image quality in direct thermal neutron radiography.1.1 This practice covers the fabrication of Sensitivity Indicators (SI), which can be used to determine the relative quality of radiographic images produced by direct, thermal neutron radiographic examination. 1.2 The values stated in inch-pound units are regarded as the standard. The SI equivalents given in parentheses in the text are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Fabrication of Neutron Radiographic Sensitivity Indicators

ASTM E2023-99 中子射线照相敏感度显示器制造的标准操作规程

1.1 This practice covers the fabrication of Sensitivity Indicators (SI), which can be used to determine the relative quality of radiographic images produced by direct, thermal neutron radiographic examination. 1.2 The values stated in inch-pound units are regarded as the standard. The SI equivalents given in parentheses in the text are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Fabrication of Neutron Radiographic Sensitivity Indicators

BS EN 61747-5:1998 液晶和固态显示装置 环境、耐久性和机械测试方法

Establishes uniform preferred test methods, including visual, with preferred values for stress levels for judging the environmental properties of liquid crystal display devices.

Liquid crystal and solid-state display devices. Environmental, endurance and mechanical test methods

NAVY MIL-V-82440 NOTICE 1-1998 燃料互锁电子管

MIL-V-82440, including Amendment 3 , dated 7 July 1969, is inactive for new design and is no longer used, except for replacement purposes.

VALVE, FUEL INTERLOCK

NAVY MIL-V-82443 NOTICE 1-1998 切断燃烧电子管

MIL-V-82443, including Amendment 1, dated 27 January 1989, is inactive for new design and is no longer used, except forreplacement purposes.

VALVE, FUEL SHUT-OFF

SJ/T 11162-1998 GZS8-6型彩色显像管插座详细规范

本规范规定了GZS8-6型彩色显像管插座的详细要求。 本规范适用于管基代号为J8-6(见GB 11490)的彩色显像管插座。 本规范应与GB／T 15176同时使用。

Detail specification for type GZS8-6 sockets for colour picture tubes

SJ/T 11163-1998 GZS10-2型彩色显像管插座详细规范

本规范规定了GZS10-2型彩色显像管插座的详细要求。 本规范适用于管基代号为J10-2(见GB 11490)的彩色显像管插座。 本规范应与GB／T 15176同时使用。

Detail specification for type GZS10-2 sockets for colour picture tubes

SJ/T 11164-1998 GZS12-4型彩色显像管插座详细规范

本规范规定了GZS12-4型彩色显像管插座的详细要求。 本规范适用于管基代号为J12-4(见GB 11490)的彩色显像管插座。 本规范应与GB／T 15176同时使用。

Detail Specification for type GZS12-4 sockets for colour picture tubes

CEA-600.34-1998 红外物理层和介质规格

This document is the preliminary specification for the CEBus Infrared (IR) Physical Layer and Medium portion of the Physical Layer and Medium specifications of EIA-600.

IR Physical Layer and Medium Specification

CEA-600.35-1998 射频物理层和介质规格

This document is the preliminary specification for the CEBus Radio Frequency (RF) Physical Layer and Medium portion of the Physical Layer and Medium specifications of EIA-600. Its purpose is to present all of the information necessary for the development of a RF physical layer for a CEBus device. This is one of a series of documents covering various media that comprise the CEBus standard.

RF Physical Layer and Medium Specification

SJ 20477.2-1997 DP-10型512×512线交流等离子体显示器件详细规范

Detail specification for type DP-10 512×512 line a.c.plasma display device

SJ 20477.3-1997 DP-12型640×400线交流等离子体显示器件详细规范

Detail specification for type DP-12 640×400 line a.c.plasma display device

SJ 20456/1-1997 SF-2108型热释电视象管详细规范

Detail specification for pyroeletric vidicon of type SF-2108

SJ 20474.2-1997 RQ-10型冷阴极触发管详细规范

Detail specification for cold cathode trigger tube of type RQ-10

DIN EN 113000:1996 总规范.摄象管

The document has been prepared for those member countries taking part in the System who wish to issue national harmonizes specifications for Camera Tubes. It should be read in conjunction with document CECC 00100: Basic Rules (1974).

Generic specification - Camera tubes; German version EN 113000:1991