N61 实验室基础设备 标准查询与下载

DIN EN 14175-6:2006-08 通风柜.第6部分:空气变量通风柜

Fume cupboards - Part 6: Variable air volume fume cupboards English version of DIN EN 14175-6:2006-08

DIN EN 14727:2006 实验室设备.实验室存储设备.要求和试验方法.德文版本 EN 14727-2005

This European Standard specifies requirements and test methods for storage units (see 3.1 used in laboratones. This European Standard specifies strength, durability and safety requirements to prevent serious injury through normal functional use, as well as misuse that might reasonably be expected to occur Safety, depending on the structure of the building, is not included e.g. the strength of wall hanging cabinets includes only the cabinet and its parts. The wall and the fixing in the wall are not included. It should be understood that the tests do not ensure that structural failure will not eventually occur as a result of habitual misuse or after an excessively long period of service. Assessment of ageing, degradation and the heating effect of appliances are not included nor are ergonomic aspects or resistance to fire.

Laboratory furniture - Storage units for laboratories - Requirements and test methods; English version of DIN EN 14727:2006-03

DLA A-A-50752 A VALID NOTICE 1-2006 渗透性测试包

A-A-50752A, dated 25 September 2001, has been reviewed and determined to be valid for use in acquisition.

TEST KIT, PENETRANT

DIN 12980:2005 实验室装置.细胞毒性物质操作用安全台

Laboratory furniture - Safety cabinets for handling cytotoxic substances

ISO/IEC 17025:2005 检测和校准实验室能力的一般要求

1．1 本标准规定了实验室进行检测和(或)校准的能力(包括抽样能力)的通用要求。这些检测和校准 包括应用标准方法、非标准方法和实验室制定的方法进行的检测和校准。 1．2本标准适用于所有从事检测和(或)校准的组织，包括诸如第一方、第二方和第三方实验室，以及将 检测和(或)校准作为检查和产品认证工作一部分的实验室。 本标准适用于所有实验室，不论其人员数量的多少或检测和(或)校准活动范围的大小。当实验室 不从事本标准所包括的一种或多种活动，例如抽样和新方法的设计(制定)时，可不采用本标准中相关条 款的要求。 1．3本标准中的注是对正文的说明、举例和指导。它们既不包含要求，也不构成本标准的主体部分。 1．4本标准用于实验室建立质量、行政和技术运作的管理体系。实验室的用户、监管机构和认可机构 也可使用本标准对实验室的能力进行确认或承认。本标准不旨在用作实验室认证的基础。 注1：术语“管理体系”在本标准中是指控制实验室运作的质量、行政和技术体系。 注2：管理体系的认证有时也称为注册。 1．5本标准不包含实验室运作中应符合的法规和安全要求。 1．6 如果检测和校准实验室遵守本标准的要求，其针对检测和校准活动所运作的质量管理体系也就满 足了GB／T 19001的原则。附录A提供了本标准与GB／T 1900]的条款对照。本标准包含了 GB／T 19001中未包含的技术能力要求。 注1：为确保应用的一致性，或许有必要对本标准的某些要求进行说明或解释。附录B给出了制定特定领域应用细 则的指南，尤其适用于认可机构(见GB／T 27011)。 注2：如果实验室希望其部分或全部检测和校准活动获得认可，应当选择一个依据GB／T 27011运作的认可机构。

General requirements for the competence of testing and calibration laboratories

IEC 61010-2-061:2005 测量、控制和实验室用电气设备的安全要求.第2-061部分:具有热原子化和离子化的实验室用原子能谱仪的特殊要求

This part of IEC 61010 applies to electrically powered laboratory atomic spectrometers with thermal atomization. It has the status of a group safety publication in accordance with IEC Guide 104

Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-061: Particular requirements for laboratory atomic spectrometers with thermal atomization and ionization

SN/T 1538.1-2005 培养基制备指南.第1部分:实验室培养基制备质量保证通则

本SN/T 1538的部分规定了与培养基制备质量保证相关的通用术语和食品或饲料微生物学分析用培养基的最低要求。 本部分适用于以下三种培养基： —商品化即用型培养基； —商品化脱水合成培养基(包括完全培养基和需添加补充物的基础培养基)； —各别成分制备的培养基。

Guidelines on preparation and production of culture media - Part 1: General guidelines on quality assurance for the preparation of culture media in the laboratory

IEC 61010-2-051:2005 测量、控制和实验室用电气设备的安全要求.第2-051部分:混合和搅拌用实验室设备的特殊要求

This part of IEC 61010 is applicable to electrically operated laboratory equipment and its accessories for mechanical mixing and stirring, where mechanical energy influences the shape or size or homogeneity of materials and their accessories. Such device

Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-051: Particular requirements for laboratory equipment for mixing and stirring

ASTM E2402-05 热重分析仪的质量损耗和剩余量测量验证的标准试验方法

This method may be used to validate the performance of a specific TGA apparatus. This method may be used to validate the performance of a specific method based upon a TGA mass loss or residue measurement. This method may be used to determine the repeatability of a specific apparatus, operator or laboratory. This method may be used for specification and regulatory compliance purposes.1.1 This method provides procedures for validating mass loss and residue measurements by thermogravimetric analyzers (TGA) and analytical methods based upon the measurement of mass loss or residue content. Performance parameters determined include mass loss and residue repeatability (precision), detection limit, quantitation limit, linearity and bias.1.2 Validation of apparatus performance and analytical methods is requested or required for quality initiatives or where results may be used for legal purposes.1.3 SI units are the standard.1.4 There is no ISO standard equivalent to this method.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Mass Loss and Residue Measurement Validation of Thermogravimetric Analyzers

NF C23-561*NF EN 50381:2004 配备或不配备室内排气装置的移动式通风房间

Transportable ventilated rooms with or without an internal source of release.

DIN EN 14175-4:2004-12 通风柜.第4部分:现场试验方法

The standard specifies on-site test methods for the assessment of safety and performance of installed fume cupboards. Test methods are specified for commissioning testing and maintenance testing of type tested (according EN 14175-3) and non-type tested fume cupboards. In addition, a qualification test for non-type tested fume cupboards is specified.#,,#

Fume cupboards - Part 4: On-site test methods; German version EN 14175-4:2004

KS J ISO 14698-2:2004 洁净室和相关可控环境.生物污染控制.第2部分:生物污染数据的评估和解释

이 규격은 미생물적 데이터를 평가하고, 생물 오염 제어를 위해 위험 지역의 생물 입자를 시

Cleanrooms and associated controlled environments-Biocontamination control-Part 2:Evaluation and interpretation of biocontamination data

SN/T 1482-2004 实验室内部质量控制方法.MR统计合并动态跟踪监控技术

Practice for laboratory internal quality control - MR pooled dynamic-ongoing-monitor technique

ARMY A-A-52298 B-2004 测量使用的三脚架:脚架可伸展型

Abstract. This CID covers an extension-leg type tripod to mount and support surveying instruments for use.

TRIPOD, SURVEYING: EXTENSION-LEG TYPE

NF X15-203-3:2004 通风柜.第3部分:类型试验方法

Fume cupboards - Part 3 : type test methods.

DIN EN ISO 14698-1:2004 洁净室和相关控制环境.生物污染控制.第1部分:总则和方法

Cleanrooms and associated controlled environments - Biocontamination control - Part 1: General principles and methods (ISO 14698-1:2003); German version EN ISO 14698-1:2003

DIN EN 14175-3:2004 通风柜.第3部分:定型试验方法

Part 3 of this European Standard specifies type test methods for the assessment of safety and performance of fume cupboards, especially requirements for the air flow, the sash and the mechanical stability. Type test methods are among others face velocity, containment, robustness of containment, air exchange efficiency, pressure drop and sash suspension.

Fume cupboards - Part 3: Type test methods; German version EN 14175-3:2003

DIN EN ISO 14698-2:2004 洁净室和相关控制环境.生物污染控制.第2部分:生物污染数据的评估和说明

This International Standard gives guidance on basic principles and methodological requirements for all microbiological data evaluation, and the estimation of biocontamination data obtained from sampling for viable particles in zones at risk, as specified by the system selected. This part of ISO 14698 is intended to be used in conjunction with the other standards of the ISO 14698 series and their annexes, where appropriate. This standard is not intended for testing the performance of microbiological counting techniques of determining viable units; e. g., by plate count methods, which should be carried out periodically, and for which ISO E 30 may apply.

Cleanrooms and associated controlled environments - Biocontamination control - Part 2: Evaluation and interpretation of biocontamination data (ISO 14698-2:2003); German version EN ISO 14698-2:2003

ANSI/SBS 2-2004 小型板.高度尺寸

Describes the height dimensions required of a microplate that is considered to meet the standards. This standard also outlines the conditions required for making necessary measurements.

Microplates - Height Dimensions

ANSI/SBS 1-2004 小型板."脚印图"尺寸

Describes the footprint dimensions required of a microplate that is considered to meet the standards. Also outlines the conditions required for making necessary measurements

Microplates - Footprint Dimensions