P94 金属设备与工艺管道安装工程 标准查询与下载

ISO 10928:2009/Amd 1:2013 塑料管道系统.玻璃增强热固塑料(GRP)管和配件.回归分析及其使用方法.修改件1

Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Methods for regression analysis and their use; Amendment 1

BS ISO 8277:2013 船舶与海洋技术.管道工程与机械.信息传递

Ships and marine technology. Pipework and machinery. Information transfer

BS EN ISO 11299-1:2013 地下铺设送气管道翻修用塑料管道系统.总则

Plastics piping systems for renovation of underground gas supply networks. General

DIN EN 14364:2013 压力和无压力排水和排污塑料管道系统.基于不饱和聚酯树脂(UP)的玻璃增强热固性塑料(GRP).管件、配件和连接件的规格.德文版本EN 14364-2013

Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints; German version EN 14364:2013

DIN EN ISO 11299-3:2013 地下铺设送气管道维修用塑料管道系统.第3部分:紧密配合管衬里(ISO 11299-3-2011).德文版本EN ISO 11299-3-2013

Plastics piping systems for renovation of underground gas supply networks - Part 3: Lining with close-fit pipes (ISO 11299-3:2011); German version EN ISO 11299-3:2013

DIN EN ISO 10380:2013 管道系统.波纹状金属软管和软管组件(ISO 10380-2012).德文版本EN ISO 10380-2012

This International Standard specifies the minimum requirements for the design,manufacture,testing and installation of corrugated metal hose and metal hose assemblies.

Pipework - Corrugated metal hoses and hose assemblies (ISO 10380:2012); German version EN ISO 10380:2012

ANSI/UL 1978-2013 润滑脂管道的安全性标准

Standard for Safety for Grease Ducts

ANSI/ASTM F2817:2013 聚氯乙烯(PVC)气体压力管道及配件维护或维修规范

Specification for Poly(Vinyl Chloride) (PVC) Gas Pressure Pipe and Fittings for Maintenance or Repair

ANSI/SMACNA 005-2013 圆形工业管道施工标准

Round Industrial Duct Construction Standards

ANSI/ASTM E2816:2013 抗燃金属暖通空调(HVAC)输送管系统的试验方法

Test Methods for Fire Resistive Metallic HVAC Duct Systems

ASTM C12-13 上釉粘土管道安装的标准实施规程

1.1 This practice covers the proper methods of installing vitrified clay pipe lines in order to fully utilize the structural properties of such pipe. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Installing Vitrified Clay Pipe Lines

ASTM F412-13 与塑料管道系统有关的标准术语

1.1 This terminology is a compilation of definitions of technical terms used in the plastic piping industry. Terms that are generally understood or adequately defined in other readily available sources are not included. 1.2 When a term is used in an ASTM document for which Committee F17 is responsible it is included only when judged, after review, by Subcommittee F17.91 to be a generally usable term. 1.3 Definitions that are identical to those published by other ASTM committees or other standards organizations are identified with the committee number (for example, D20) or with the abbreviation of the name of the organization (for example, IUPAC International Union of Pure and Applied Chemistry). 1.4 A definition is a single sentence with additional information included in notes. 1.5 Definitions are followed by the committee responsible for the standard(s) (for example, [F17.26]) and standard numbers(s) in which they are used (for example, F714).

Standard Terminology Relating to Plastic Piping Systems

ANSI/ASTM D2513:2013 聚乙烯(PE)压力管,管道和配件用规格

Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings

ANSI/ASTM F412:2013 塑料管道系统相关术语学

Terminology Relating to Plastic Piping Systems

ANSI/ASTM F2487:2013 已安装高密度聚乙烯波纹管材渗漏验收试验的实施规程

Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Corrugated High Density Polyethylene and Polypropylene Pipelines

ASTM F1000-13 管道系统图符号的标准实施规程

2.1 Figure 1 provides symbols for strainers, separators, and filters. 2.2 Figure 2 provides symbols for valves. Valves are categorized under the following headings: globe, angle, check, ball, butterfly, gate, relief, manifolds, control, noise control, and miscellaneous. 2.3 Figure 3 provides symbols for valve appendages such as actuators and locking devices. Symbols shown on Fig. 3 are to be combined with the appropriate symbol from Fig. 2. 2.4 Figure 4 provides symbols for piping system–related instrumentation. These symbols are categorized under the following headings: pressure, temperature, flow, level, switches, alarms, and miscellaneous. 2.5 Figure 5 provides symbols for fans, pumps, and turbines. 2.6 Figure 6 provides symbols for plumbing components. 2.7 Figure 7 provides symbols for pipe and pipe fittings. 2.8 Figure 8 provides symbols for noise control components and designations. These symbols are generally used for submarine design. 2.9 Figure 9 provides symbols for transitions. These symbols identify transitions such as pipe material or pipe schedule changes. 2.10 Figure 10 provides symbols for miscellaneous components. These are components which could not be classified under the above categories. Examples include heat exchangers, flasks, and sea chests. 2.11 Figure 11 provides symbols for grooved piping. 1.1 This practice establishes piping system drawing symbols for marine use. 1.2 This set of standard symbols is intended for use on piping system diagrammatics and arrangements for ships. 1.3 Where graphical symbols are required for an item or equipment not covered by this practice, the form and character of the symbol will be left to the discretion of the activity concerned, provided that the symbol used does not duplicate any of those contained herein, and is clearly understandable, subject to one interpretation only, or explained by a suitable note on the drawing when necessary. 1.4 Since symbolic representation does not usually involve exact or scale layout or the actual run or leads of piping, the same symbol may be used for all projections of the system (plan, elevations, and sections). 1.5 Symbols for fluid power, heating, ventilation, and air conditioning (HVAC), and Navy damage control diagrams are not included in this practice.

Standard Practice for Piping System Drawing Symbols

ANSI/ASTM F2164:2013 采用液压法进行聚乙烯(PE)压力管道系统场漏试验的实施规程

Practice for Field Leak Testing of Polyethylene (PE) Pressure Piping Systems using Hydrostatic Pressure

ASTM A798/A798M-13 污水管及其它类似用途用工厂制波纹钢管安装的标准实施规程

1.1 This practice covers procedures, soils, and soil placement for the proper installation of corrugated steel pipe and pipe-arches produced to Specification A760/A760M or A762/A762M, in either trench or embankment installations. A typical trench installation and a typical embankment (projection) installation are shown in Figs. 1 and 2, respectively. The pipes described in this practice are manufactured in a factory and furnished to the job in lengths ordinarily from 10 to 30 ft [3 to 9 m], with 20 ft [6 m] being common, for field joining. This practice applies to structures designed in accordance with Practice A796/A796M. FIG. 1 Typical Trench Installation FIG. 2 Typical Embankment (Projection) Installation 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.3 This specification is applicable to design in inch-pound units as A798 or in SI units as A798M. Inch-pound units and SI units are not necessarily equivalent. SI units are shown in brackets in the text for clarity, but they are the applicable values when the installation is to be performed in accordance with A798M.

Standard Practice for Installing Factory-Made Corrugated Steel Pipe for Sewers and Other Applications

BS EN 13480-4:2012+A1:2013 工业用金属管道. 制造和安装

Metallic industrial piping. Fabrication and installation

BS EN 13480-5:2012+A1:2013 工业用金属管道. 检查和试验

Metallic industrial piping. Inspection and testing