Q27 粘结材料 标准查询与下载

ASTM C1707-10 液压石灰火山灰结构用的标准规范

1.1 This standard covers four types of pozzolanic hydraulic lime for structural purposes which include use in mortar, scratch, brown, and finish (stucco) coats of interior or exterior plaster. 1.1.1 PHL8212;Pozzolanic hydraulic lime for use in mortar, scratch, brown, and finish (stucco) coats of interior or exterior plaster. 1.1.2 PHLc8212;PHL with a maximum 20 % binder weight of hydraulic cement. 1.1.3 PHL-A8212;Air-entrained PHL. 1.1.4 PHLc-A8212;Air-entrained PHLc. 1.2 This specification classifies pozzolanic hydraulic lime by minimum hydrated lime content, maximum hydraulic cement content, and specific performance requirements. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Appropriate conversion can be done using . 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Pozzolanic Hydraulic Lime for Structural Purposes

ASTM C110-10 生石灰,熟石灰和石灰石的标准试验方法和物理测试

1.1 These test methods cover physical testing of quicklime and hydrated lime, and of limestone not otherwise covered in ASTM standards. Note 18212;Quicklime and hydrated lime have a high affinity for moisture and carbon dioxide. Caution should be taken to protect both hydrated and quicklime during sampling, storage, and testing (see Practice C50).

Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone

ASTM C881/C881M-10 混凝土用环氧树脂基粘结系统的标准规范

1.1 This specification covers two-component, epoxy-resin bonding systems for application to portland-cement concrete, which are able to cure under humid conditions and bond to damp surfaces. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Some values have only SI units because the inch-pound equivalents are not used in practice. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements, see Section 9.

Standard Specification for Epoxy-Resin-Base Bonding Systems for Concrete

ASTM C977-10 土壤保持稳定用生石灰和熟石灰标准规格

1.1 This specification pertains to quicklime and hydrated lime, either high calcium, dolomitic, or magnesian lime, for use in stabilization of soils (See Note 2). Note 18212;Quicklime and hydrated lime act upon clay soils and may render such soils suitable for highway construction and for other load-bearing applications. In most cases, lime causes finely divided clay particles to agglomerate into coarser particles which improves load-bearing properties and subsequently the lime-treated soil hardens by chemical reaction. Note 28212;No attempt is made to present requirements for by-product lime, commercial lime slurry, etc. Specification requirements for these materials could be better determined on a local basis. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Quicklime and Hydrated Lime for Soil Stabilization

ASTM E874-10a 保护板用非金属蜂窝状芯体铝盖面的粘合剂粘结的标准操作规程

The formation of reproducible, durable-adhesive bonds in structural units requires great care in the selection of materials, the preparation of the surfaces of the parts to be bonded, and the performance of the steps in the bonding process. Experience has shown that adhesive bonding carried out in accordance with this practice produces relatively reproducible bonds. 1.1 This practice describes the materials, processes, and quality controls to be used in the manufacture of adhesive-bonded, aluminum-faced, nonmetallic-honeycomb-core sandwich panels for tactical shelters. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Adhesive Bonding of Aluminum Facings to Nonmetallic Honeycomb Core for Shelter Panels

JC/T 620-2009 石灰取样方法

本标准规定了石灰取样的批量、工具、地点、部位、方法及样品的数量、制备、包装、贮存等。

Sampling method of lime

JC/T 621-2009 硅酸盐建筑制品用生石灰

本标准规定了硅酸盐建筑制品用生石灰的术语、等级、技术要求、试验方法、检验规则、运输及贮存。 本标准适用于蒸压加气混凝土、蒸压灰砖、粉煤灰砖及粉煤灰砌块等硅酸盐建筑制品用的生石灰。

Lime for silicate building products

SANS 523:2009 建筑用石灰

Covers quicklime and slaked (hydrated) limes for use in building and produced by calcining of limestone, or treatment of calcium carbide.

Limes for use in building

DIN EN 12808-4:2009 瓷砖的灌浆材料.第4部分:收缩率的测定,德文版本EN 12808-4:2009

This European Standard applies to all ceramic tile grouts for internal and external tile installations on walls and floors. This European Standard specifies the test method to be used to determine the shrinkage of ceramic tile grouts This European Standard does not contain performance requirements or recommendations for the design and installation of ceramic tiles. NOTE Ceramic tile grouts can also be used for other types of tiles (natural and agglomerated stones, etc.), where these do not adversely affect the stones.

Grouts for tiles - Part 4: Determination of shrinkage; English version of DIN EN 12808-4:2009-10

DB65/T 3017-2009 电石用石灰

Lime for Calcium carbide

KS L 9501-2009 工业用石灰

이 표준은 공업에 사용하는 석회(이하 공업용 석회라 한다.)에 대하여 규정한다. 다만 재생

Industrial lime

DIN EN 12945:2009 石灰材料.中和值的测定.滴定法(包括勘误表AC-2009).英文版本EN 12945-2008+AC-2009

This European Standard specifies two methods for the determination of the neutralizing value (NV) of liming materials. Method A is applicable to all liming materials except silicate liming materials and liming materials with more than 3 % PO. Method B is applicable to all liming materials except products with more than 3 % mass fraction P205, and calcined and slaked products of carbonate origin, NOTE The methods described in ISO 6598 and ISO 7497 can be used for the determination of P205 content (see [2] and [3]).

Liming materials - Determination of neutralizing value - Titrimetric methods(includes Corrigendum AC:2009); English version of DIN EN 12945:2009-09

NF T66-011:2009 沥青和沥青粘合剂.工业沥青加热后质量损失的测定

Bitumen and bituminous binders - Determination of the loss in mass after heating of industrial bitumen.

NF T66-052*NF EN 12850:2009 沥青和沥青粘合剂.沥青乳液pH值的测定

Bitumen and bituminous binders - Determination of the pH value of bituminous emulsions.

DIN EN 12591:2009 沥青和沥青粘合剂.铺路级沥青规范.英文版本DIN EN 12591-2009-08

This European Standard provides a framework for specifying a range of properties and relevant test methods for bitumens, which are suitable for use in the construction and maintenance of roads, airfields and other paved areas, together with requirements for evaluation of conformity. This European Standard does not directly address 'cohesion, adhesion and setting ability' (see Introduction). NOTE Although industrial bitumens are specified according to EN 13305, it should be underlined that paving grade bitumens, specified according to this European Standard, can also be used for industrial applications.

Bitumen and bituminous binders - Specifications for paving grade bitumens; English version of DIN EN 12591:2009-08

DIN EN 15326:2009 沥青和沥青粘合剂.密度和比重的测量.毛细管塞比重瓶法(包括修改件A1-2009).英文版本DIN EN 15326-2009-08

This European standard specifies a procedure for determining the specific gravity and density of bituminous binders at (25,0 + 0,2) ℃ using the capillary-stoppered pyknometer method. Emulsions are excluded from the scope of this method. NOTE 1 This method can also be used for other hydrocarbon binders, for bituminous binders from other sources, e.g. recovered from asphalt or after hardening and for bituminous binders containing filler. However, a lower precision is to be expected. NOTE 2 This test method may be performed at other temperatures (i.e. 15 ℃). When doing so, the density values of water and isopropanol should be determined. The pyknometer method shall be used as a reference method for determining the specific gravity and density of bituminous binders.

Bitumen and bituminous binders - Measurement of density and specific gravity - Capillary-stoppered pyknometer method(includes Amendment A1:2009); English version of DIN EN 15326:2009-08

NF T76-338:2009 建筑粘合剂.特性标准数据库

Structural adhesives - A standard database of properties.

NF T66-017-1:2009 沥青和沥青粘合剂.断裂性能的测定.第1部分:阳离子沥青乳液断裂值的测定,矿物填料法

Bitumen and bituminous binders - Determination of breaking behaviour - Part 1 : determination of breaking value of cationic bituminous emulsions, mineral filler method.

NF T66-017-2:2009 沥青和沥青粘合剂.断裂特性的测定.第2部分:阳离子沥青乳液细粒混合时间的测定

Bitumen and bituminous binders - Determination of breaking behaviour - Part 2 : determination of fines mixing time of cationic bitumen emulsions.

BS EN 13897:2004 防水柔性薄板材.屋顶防水用沥青,塑料和橡胶薄板材.低温拉伸后的防水性测定

This document specifies a test for determining the ability of flexible sheets to remain watertight after being stretched at low temperature. This standard is applicable only for mechanically fastened single layer waterproofing. This standard has been drafted for application in roofing, but it may also be used in other areas where it is relevant.

Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of watertightness after stretching at low temperatures