Q92 水泥与水泥制品设备 标准查询与下载

JC/T 738-2004 水泥强度快速检验方法

Accelerated test method for cement strength

JC/T 938-2004 水泥工业用多风道煤粉燃烧器技术条件

本标准规定了水泥工业用多风遭煤粉燃烧器的技术要求、 试验方法、 检验规则以及标志、 包装、 运 输和贮存。 本标准适用于水泥工业用多风道煤粉燃烧器】包括口转窑用、 分解炉用和预燃室用多风道煤粉燃烧 器(以一简称燃烧器〕。 其他行业用燃烧器也可参照使斥。

Technical conditions of multi-air channel coal burner for cement industry

BS EN 12637-1:2004 混凝土结构的保护和维修用产品和系统.试验方法.注入产品的可混用性.与混凝土的可混用性

This document describes the method for determining the compatibility with concrete of polyurethane injection products, or other elastic injection products likely to be sensitive to the effects of the alkalis in concrete. This document describes the reference procedure. In the case of polyurethane products, this method is only suitable for final injection products (i.e. not water-stopping foams).

Products and systems for the protection and repair of concrete structures - Test methods - Compatibility of injection products - Compatibility with concrete

BS EN 13584:2003 混凝土结构的保护和维修用产品和系统.试验方法.维修产品的压缩蠕变测定

This European Standard specifies a method for measuring creep under compressive load in products and systems for the repair of concrete structures, as defined in prEN 1504-3.The method is suitable for repair mortars and concretes with polymer binders (PC) and repair grouts, mortars and concretes with hydraulic binders (CC) and polymer cement binders (PCC).

Products and systems for the protection and repair of concrete structures - Test methods - Determination of creep in compression for repair products

BS EN 13584:2004 混凝土结构的保护和维修用产品和系统.试验方法.维修产品的压缩蠕变测定

Products and systems for the protection and repair of concrete structures - Test methods - Determination of creep in compression for repair products

DIN EN 13295:2004 混凝土结构的防护和维修用产品和系统.试验方法.抗碳化性测定

This European Standard specifies an accelerated laboratory method for measuring the resistance against carbon dioxide penetration through repair products and systems, as defined in prEN 1504-3. The method is based on measurement of the depth of carbonation of the sample in a concentrated carbon dioxide atmosphere over a fixed time interval. The method is suitable for assessing the performance of repair grouts, mortars and concretes without a protective coating system applied. The method does not measure the resistance to reduction in pH-value that may occur by absorption of other acidic gases (e. g. SO2, HCl).#,,#

Products and systems for the protection and repair of concrete structures - Test methods - Determination of resistance to carbonation; German version EN 13295:2004

BS EN 13295:2004 混凝土结构的保护和维修用产品和系统.试验方法.抗碳化作用的测定

This European Standard specifies an accelerated laboratory method for measuring the resistance against carbon dioxide penetration through repair products and systems, as defined in prEN 1504-3. The method is based on measurement of the depth of carbonation of the sample in a concentrated carbon dioxide atmosphere over a fixed time interval. The method is suitable for assessing the performance of repair grouts, mortars and concretes without a protective coating system applied. The method does not measure the resistance to reduction in pH-value that may occur by absorption of other acidic gases (e.g. SO2, HCI).

Products and systems for the protection and repair of concrete structures.Test methods - Determination of resistance to carbonation

BS EN 13396:2004 混凝土结构的保护和维修的产品和设备.试验方法.氯离子浸入的测量

This European Standard specifies a method for determining the resistance to chloride ion penetration of hardened CC or PCC repair products and systems for the protection and repair of concrete, as defined in prEN 1504-3. The provisions of the standard are applicable to cementitious grouts, mortars and concretes with a maximum aggregate size of 20 mm.

Products and systems for the protection and repair of concrete structures - Test methods - Measurement of chloride ion ingress

BS EN 12629-5-1:2004 生产混凝土和硅酸钙建筑产品用机械.安全.在垂直轴上生产的制管机

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Pipe making machines manufacturing in the vertical axis

BS EN 12629-5-1:2003+A1:2010 生产混凝土和硅酸钙建筑产品用机械.安全性.在垂直轴上生产的制管机

1.1 This part of EN 12629, taken together with EN 12629-1:2000+A1:2010, applies to machines for vertical manufacture of pipes, manholes and similar elements from concrete. EN 12629-1:2000+A1:2010 specifies general requirements applicable to machines for the manufacture of constructional products from concrete and calcium–silicate. This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific to the machines it covers. 1.2 This European Standard deals with all significant hazards pertinent to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. This standard establishes safety requirements and/or methods of protection which applies to these machines. 1.3 This European standard applies to the pipe making machines manufacturing in the vertical axis which may form an integral part of a pipe making process plant. 1.4 This document is not applicable to pipe making machines manufacturing in the vertical axis, which are manufactured before the date of publication of this document by CEN.

Machines for the manufacture of constructional products from concrete and calcium-silicate. Safety. Pipe making machines manufacturing in the vertical axis

BS EN 12629-5-3:2003+A1:2010 生产混凝土和硅酸钙建筑产品用机械.安全性.管预应力机

1.1 This part of EN 12629, taken together with EN 12629-1:2000+A1:2010, applies to pipe prestressing machines as defined in Clause 3. EN 12629-1:2000+A1:2010 specifies general requirements applicable to machines for the manufacture of constructional products from concrete and calcium–silicate. This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific to the machines it covers. 1.2 This European Standard deals with all significant hazards pertinent to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. This standard establishes safety requirements and/or methods of protection which applies to these machines. 1.3 This European standard applies to the concrete pipe prestressing machines which may form an integral part of a pipe making process plant. 1.4 This document is not applicable to pipe prestressing machines, which are manufactured before the date of publication of this document by CEN.

Machines for the manufacture of constructional products from concrete and calcium-silicate. Safety. Pipe prestressing machines

BS EN 12629-5-3:2004 生产混凝土和硅酸钙建筑产品用机械.安全.管预应力机

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Pipe prestressing machines

BS EN 12629-5-2:2003+A1:2010 生产混凝土和硅酸钙建筑产品用机械.安全性.在水平轴上生产的制管机

1.1 This part of EN 12629, taken together with EN 12629-1:2000+A1:2010, applies to machines for the manufacture of pipes in the horizontal axis and similar elements from concrete. EN 12629-1:2000+A1:2010 specifies general requirements applicable to machines for the manufacture of constructional products from concrete and calcium–silicate. This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific to the machines it covers. 1.2 This European Standard deals with all significant hazards pertinent to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. This standard establishes safety requirements and/or methods of protection which applies to these machines. 1.3 This European standard applies to the pipe making machines manufacturing in horizontal axis which may form an integral part of a pipe making process plant. 1.4 This document is not applicable to pipe making machines manufacturing in the horizontal axis, which are manufactured before the date of publication of this document by CEN.

Machines for the manufacture of constructional products from concrete and calcium-silicate. Safety. Pipe making machines manufacturing in the horizontal axis

BS EN 12629-7:2004 生产混凝土和硅酸钙建筑产品用机械.安全.预应力产品长线生产用固定式和移动式设备

1 This European Standard is intended to be used together with EN 12629-1 "Machines for the manufacture of constructional products from concrete and calcium-silicate —Safety —Part 1: Common requirements", which specifies general requirements of machines for the manufacture of constructional products from concrete and calcium-silicate. The manufacturing bed is a machine with which other associated machines work simultaneously. Moreover, these machines are generally used on beds installed in parallel. 2 This standard gives particular requirements for the design of the following machines: — Pre-stressing bed (schematic representation is given in annex A); — Bed sweeper, vacuum cleaner, oiler, wire-guide machine (schematic representation is given in annex B); — Bed layout machine (schematic representation is given in annex C); — Strand pushing/pulling machine (schematic representation is given in annex D); — Spinner, extruder, vibrodistributor (schematic representation is given in annex E); — Tarpaulin paying out and winding in machine (schematic representation is given in annex F); — Sawing machine (schematic representation is given in annex G). NOTE The manufacturing operations include some or all of the following: — treating pre-stressing bed with release agent; — "marking out" the elements (slabs, plain slabs, etc.) to be made; — running the pre-stressing strands; — pre-tensioning; — installing the shutterings, (formwork, side shutters, end plates and inserts) — fixing reinforcement; — tensioning; — concrete distribution and compaction; — winding out the tarpaulin; — heating; — detensioning; — removal of shettering, formwork, etc.; — strands cutting or sawing; — removal of final products; — bed cleaning. The concrete supply interface which is taken into account for safety is also considered. The sequence of these operations can be different according to the manufacturing process used in the factory and to the various types of products. 3 This European Standard deals with the significant hazards pertinent to these machines, when they are used as intended under the conditions foreseen by the manufacturer (see clause 4), except noise hazards which are partly dealt with and hazards due to handling the package of cut wires and placing them on beds. NOTE Amendment is under preparation to deal with noise, in particular for measures to reduce noise at source and a noise test code including noise declaration. This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. 4 Sub-clause 1.3 of EN 12629-1:2000 applies. 5 Sub-clause 1.4 of EN 12629-1:2000 applies. NOTE At the designing stage, in complement to this standard, other type C standards dealing with similar hazards can be used for some of the machines and equipment mentioned in this standard. EN 13862 for Floor sawing machines or EN 1454 on portable saws can be a help to design the saws described in this standard. 6 This document is applicable to equipment for long-line manufacture of pre-stressed product which are manufactured after the date of publication of this document by CEN.

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Stationary and mobile equipment for long line manufacture of prestressed products

BS EN 12629-5-2:2004 生产混凝土和硅酸钙建筑产品用机械.安全.在水平轴上生产的制管机

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Pipe making machines manufacturing in the horizontal axis

BS EN 12629-7:2004+A1:2010 生产混凝土和硅酸钙建筑产品用机械.安全性.预应力产品长线生产用固定式和移动式设备

1.1 .This part of EN 12629, taken together with EN 12629-1:2000+A1:2010 applies to stationary and mobile equipment for the benched manufacture of prestressed products. The manufacturing bed is a machine with which other associated machines work simultaneously. Moreover, these machines are generally used on beds installed in parallel. EN 12629-1:2000+A1:2010 specifies general requirements applicable to machines for the manufacture of constructional products from concrete and calcium–silicate. This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific to the machines it covers. 1.2 This standard gives particular requirements for the design of the following machines: ? Pre-stressing bed (schematic representation is given in annex A); ? Bed sweeper, vacuum cleaner, oiler, wire-guide machine (schematic representation is given in annex B); ? Bed layout machine (schematic representation is given in annex C); ? Strand pushing/pulling machine (schematic representation is given in annex D); ? Spinner, extruder, vibrodistributor (schematic representation is given in annex E); ? Tarpaulin paying out and winding in machine (schematic representation is given in annex F); ? Sawing machine (schematic representation is given in annex G). 1.3 !This European Standard deals with all significant hazards pertinent to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. 1.4 Sub-clause 1.3 of !EN 12629-1:2000+A1:2010applies. deleted text ! 1.5 "This document is applicable to equipment for long-line manufacture of pre-stressed product which are manufactured after the date of publication of this document by CEN.

Machines for the manufacture of constructional products from concrete and calcium-silicate. Safety. Stationary and mobile equipment for long line manufacture of prestressed products

BS EN 12629-5-4:2003+A1:2010 生产混凝土和硅酸钙建筑产品用机械.安全性.混凝土管涂覆机

1.1 This part of EN 12629, taken together with EN 12629-1:2000+A1:2010, applies to concrete pipe coating machines as defined in Clause 3. EN 12629-1:2000+A1:2010 specifies general requirements applicable to machines for the manufacture of constructional products from concrete and calcium–silicate. This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific to the machines it covers. 1.2 !This European Standard deals with all significant hazards pertinent to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. This standard establishes safety requirements and/or methods of protection which applies to these machines. 1.3 This European standard applies to the concrete pipe coating making machines which may form an integral part of a pipe making process plant. 1.4 This document is not applicable to concrete pipe coating machines, which are manufactured before the date of publication of this document by CEN.

Machines for the manufacture of constructional products from concrete and calcium-silicate. Safety. Concrete pipe coating machines

BS EN 12629-5.4:2004 生产混凝土和硅酸钙建筑产品用机械.安全.混凝土管涂覆机

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Concrete pipe coating machines

BS EN 12629-5.4:2003 生产混凝土和硅酸钙建筑产品用机械.安全.混凝土管涂覆机

1 This European Standard applies to concrete pipe coating machines. 2 This European Standard deals with the significant hazards listed in clause 4, when used as intended under the conditions foreseen by the manufacturer. This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards, except noise hazards. NOTE Amendment is under preparation to deal with noise, in particular for measures to reduce noise at source and a noise test code including noise declaration. This standard establishes safety requirements and/or methods of protection which applies to these machines. 3 This European standard applies to the concrete pipe coating making machines which may form an integral part of a pipe making process plant. 4 See 1.4 of EN 12629-1:2000.

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-4:Concrete pipe coating machines

JIS R 0303:2004 水泥回转窑的热平衡计算方法

この規格は，ポルトランドセメントクリンカーを製造する窯炉[ロータリーキルン(以下，キルンという。)及びその附属設備]の熱勘定方式について規定する。

Heat balancing of cement rotary kiln