Q92 水泥与水泥制品设备 标准查询与下载

JC/T 1000-2006 水泥工业用轴瓦(轴承)

本标准规定了水泥工业用轴瓦（轴承）产品分类、技术要求、检验规则、标志、运输、包装和贮存。 本标准适用于水泥工业用轴瓦（轴承），其他类似轴瓦（轴承）也可参照本标准执行。

Bearing for cement industry

JC/T 1001-2006 水泥工业用热风阀

本标准规定了水泥工业用热风阀（以下简称“热风阀”）的产品分类、技术要求、试验方法与检验规则、标志、包装、运输、贮存。 本标准适用在水泥行业大型成套设备的通风管路系统中，完成风量的自动控制和调节的热风阀。

Air pipe channel valve for cement industry

JC/T 1002-2006 水泥工业用三道锁风装置

本标准规定了水泥工业用三道锁风装置（以下简称“锁风装置”）的产品分类、技术要求、试验方法与检验规则、标志、包装、运输、贮存。 本标准适用于建材、冶金、矿山等行业的进料系统。特别适用于粘性、水份较高的原料。

Three channel gate for cement industry

JC/T 459.1-2006 水泥工业用环链斗式提升机.第1部分:型式与基本参数

本部分规定了水泥工业用高硬度，高强度环链斗式提升机的型式与基本参数。 本部分适用于水泥工业用提升粒度小于60mm、温度低于350°C物料的重力式卸料环链斗式提升机（以下简称“提升机”）。其他行业类似工况条件下也可参照使用。

Chain bucket elevator for cement plant.Part 1:Type and basic parameter

JC/T 459.2-2006 水泥工业用环链斗式提升机.第2部分:技术条件

本部分规定了水泥工业用高硬度，高强度环链斗式提升机的技术要求、试验方法和检验规则及标志、包装、运输和贮存。 本部分适用于水泥工业用环链斗式提升机（以下简称“提升机”）。

Chain bucket elevator for cement plant.Part 2:Technical condition

JC/T 460.1-2006 水泥工业用胶带斗式提升机.第1部分:型式与基本参数

本部分规定了水泥工业用钢丝绳网芯胶带斗式提升机的型式与基本参数。 本部分适用于水泥工业用提升粒度小于25mm、温度≤120°C物料的混合式卸料胶带斗式提升机（以下简称“提升机”）。

Belt bucket elevator for cement plant.Part 1:Type and basic parameter

JC/T 460.2-2006 水泥工业用胶带斗式提升机.第2部分:技术条件

本部分规定了水泥工业用钢丝绳网芯胶带斗式提升机的技术要求、试验方法和检验规则及标志、包装、运输和储存。 本部分适用于水泥工业用胶带斗式提升机（以下简称“提升机”）。

Belt bucket elevator for cement plant.Part 2:Technical condition

JC/T 335-2006 水泥工业用回转烘干机

本标准规定了水泥工业用回转烘干机的产品分类、技术要求、试验方法和检验规则、标志、包装、运输和贮存等。 本标准适用于烘干粘土、矿渣、石灰石和原煤等物料的水泥工业用回转烘干机，也适用于其他行业烘干类似物料的回转烘干机。

Rotary dryer for cement industry

JC/T 1003-2006 水泥工业用密封装置

本标准规定了水泥工业用密封装置的术语和定义、产品分类、技术要求、试验方法、检验规则、标志、包装、运输与贮存。 本标准适用于水泥工业用回转窑、单冷机、烘干机等回转机的密封装置。

Sealing device for cement industry

JC/T 333-2006 水泥工业用回转窑

Rotary kiln for cement industry

JC 333-2006 水泥工业用回转窑

本标准规定了水泥工业用回转窑（以下简称“回转窑”）的基本参数和型号、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于内径为3.0m～6.4m的普通干法和预分解回转窑。对其它窑型和规格的回转窑，也可参照本标准的有关条文执行。

Rotary kiln for cement industry

JC/T 465-2006 水泥工业用预热器分解炉系统装备技术条件

本标准规定了水泥工业用预热器分解炉系统装备（包括喂料室、旋风筒、风管、分解炉、下料管、膨胀节、锁风阀等）的技术要求、试验方法、检验规则、标志、包装、运输、贮存和安装等。 本标准适用于水泥工业用预热器分解炉系统装备（以下简称“预热器分解炉”），也适用于其他预热器。

Preheater and Precalciner for Cement Industry

JC/T 402-2006 水泥机械涂漆防锈技术条件

本标准规定了水泥机械涂漆与防锈的技术要求、试验方法及检验规则。 本标准适用于水泥机械的涂漆与防锈，其他建材机械的涂漆与防锈可参照使用。

Technical condition of paint coating and antirust for cement machinery

JC/T 334.1-2006 水泥工业用管磨机

Tube mill for cement industry

JC/T 461-2006 水泥工业用仓式泵

本标准规定了水泥工业用仓式泵的术语和定义、型号及基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于输送粉粒状干物料的各种输送形式的水泥工业用仓式泵（以下简称“仓式泵”）。其它类似产品可参照执行。

Pressure tank for cement industry

JC/T 462-2006 水泥工业用螺旋泵

本标准规定了水泥工业用螺旋泵的术语和定义、分类、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于输送低于200℃粉状干物料的水泥工业用螺旋泵（以下简称“螺旋泵”）。其它类似产品可参照执行。

Serew pump for cement industry

JC/T 463-2006 水泥工业用气力提升泵

本标准规定了水泥工业用提升泵的术语和定义、型号及基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于垂直向上输送粉状干物料的水泥工业用气力提升泵（以下简称“提升泵”）。其它类似产品可参照执行。

Air lift for cement industry

JC/T 991-2006 建材工业用石膏墙板(砌块)成型机

本标准规定了石膏墙板机的术语和定义、产品分类、技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于石膏墙板机，其类似产品可参照执行。

Gypsum partition wall panel plant

BS EN 12629-6:2004 生产混凝土和硅酸钙建筑产品用机器.安全.生产预制加筋产品的固定和移动设备

1 This document is intended to be used together with EN 12629-1 "Machines for the manufacture of constructional products from concrete and calcium-silicate —Safety —Part 1: Common requirements", which specifies general requirements of machines for the manufacture of constructional products from concrete and calcium-silicate. This document specifies the additional requirements to and/or the deviations from EN 12629-1 _specific for the stationary and mobile equipment for the manufacture of precast reinforced products as defined in Clause 3. This document applies to these machines also when used for the manufacture of non-reinforced moulded products. 2 This document applies to the modules comprising production machines (with or without turnover demoulding) for the manufacturing of reinforced moulded products as shown below and illustrated in informative Annexes A and B. NOTE This machinery can consist of three modules and they are generally designed to obtain a large moulding capacity (middle length of the products from 3 to 4 meters), with a limit height of demoulding of 1 m and a maximum width of 1,50 m. Module A: Manufacturing machines by vibration or compression and floating, with or without turnover. Module B: Stocking/hardening unit. Module C: Assembly for palletising/packaging of the concrete products. This module also permits the inspection of the products. These machines are designed to perform the following cyclic operations: — manufacturing by vibration and even compression (oiling, mould feeding - concrete + reinforcement -, vibration, floating, interlocking, turnover, removing from mould); — storage of moulds and pallet boards for concrete hardening; — products destacking and packaging; — moulds and pallet boards return to the manufacturing module. Any of these operations may be manual, semi-automatic or automatic. This document deals with automatic and semi-automatic operations of modules A and C and with automatic operations of module B. There are two main types of stationary and mobile equipment for manufacture of precast reinforced products: — equipment with instant removing from mould on pallet boards or on the floor; — equipment with delayed removing from mould (collection of moulds: the concrete products are hardened in the mould). This standard does not deal with the machines for: — mixing of concrete; — manufacturing of the reinforcing steel; — evacuation of the products to the stockyard; — manufacturing of products (e. g. slabs or blocks) covered by other parts of EN 12629. Annex A shows the most common types of units as well as their variations: immediate demoulding unit and delayed demoulding unit. 3 This document is limited to the units comprising a fixed or movable manufacturing module with or without rolling over of the mould, a module or storage area for storing/hardening of the products and a products palletising/packaging module. It deals with the significant hazards pertinent to these machines, when used as intended under the conditions foreseen by the manufacturer (see Clause 4), except noise hazards, which are partly dealt with. NOTE An amendment is under preparation to deal with noise, in particular for measures to reduce noise at source and a noise test code including noise declaration. This document specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards, particularly: — following a malfunction during the automatic mode of operation; — during manual or semi-automatic manufacturing processes; — during end-of-shift cleaning procedures, adjustment and maintenance. This document deals with the significant hazards generated by handling equipment for palletising and stacking/destacking that are gantries. Complementary safety measures can be necessary if other type of handling equipment is used. 4 This document is not applicable to stationary and mobile equipment for t

Machines for the manufacture of constructional products from concrete and calcium-silicate-Safety-Part 6:Stationary and mobile equipment for the manufacture of precast reinforced products

BS EN 12629-6:2005 生产混凝土和硅酸钙建筑产品用机器.安全.生产预制加筋产品的固定和移动设备

1 This document is intended to be used together with EN 12629-1 "Machines for the manufacture of constructional products from concrete and calcium-silicate —Safety —Part 1: Common requirements", which specifies general requirements of machines for the manufacture of constructional products from concrete and calcium-silicate. This document specifies the additional requirements to and/or the deviations from EN 12629-1 _specific for the stationary and mobile equipment for the manufacture of precast reinforced products as defined in Clause 3. This document applies to these machines also when used for the manufacture of non-reinforced moulded products. 2 This document applies to the modules comprising production machines (with or without turnover demoulding) for the manufacturing of reinforced moulded products as shown below and illustrated in informative Annexes A and B. NOTE This machinery can consist of three modules and they are generally designed to obtain a large moulding capacity (middle length of the products from 3 to 4 meters), with a limit height of demoulding of 1 m and a maximum width of 1,50 m. Module A: Manufacturing machines by vibration or compression and floating, with or without turnover. Module B: Stocking/hardening unit. Module C: Assembly for palletising/packaging of the concrete products. This module also permits the inspection of the products. These machines are designed to perform the following cyclic operations: — manufacturing by vibration and even compression (oiling, mould feeding - concrete + reinforcement -, vibration, floating, interlocking, turnover, removing from mould); — storage of moulds and pallet boards for concrete hardening; — products destacking and packaging; — moulds and pallet boards return to the manufacturing module. Any of these operations may be manual, semi-automatic or automatic. This document deals with automatic and semi-automatic operations of modules A and C and with automatic operations of module B. There are two main types of stationary and mobile equipment for manufacture of precast reinforced products: — equipment with instant removing from mould on pallet boards or on the floor; — equipment with delayed removing from mould (collection of moulds: the concrete products are hardened in the mould). This standard does not deal with the machines for: — mixing of concrete; — manufacturing of the reinforcing steel; — evacuation of the products to the stockyard; — manufacturing of products (e. g. slabs or blocks) covered by other parts of EN 12629. Annex A shows the most common types of units as well as their variations: immediate demoulding unit and delayed demoulding unit. 3 This document is limited to the units comprising a fixed or movable manufacturing module with or without rolling over of the mould, a module or storage area for storing/hardening of the products and a products palletising/packaging module. It deals with the significant hazards pertinent to these machines, when used as intended under the conditions foreseen by the manufacturer (see Clause 4), except noise hazards, which are partly dealt with. NOTE An amendment is under preparation to deal with noise, in particular for measures to reduce noise at source and a noise test code including noise declaration. This document specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards, particularly: — following a malfunction during the automatic mode of operation; — during manual or semi-automatic manufacturing processes; — during end-of-shift cleaning procedures, adjustment and maintenance. This document deals with the significant hazards generated by handling equipment for palletising and stacking/destacking that are gantries. Complementary safety measures can be necessary if other type of handling equipment is used. 4 This document is not applicable to stationary and mobile equipment for t

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Stationary and mobile equipment for the manufacture of precast reinforced products