Q92 水泥与水泥制品设备 标准查询与下载

BS EN 12629-6:2004+A1:2010 生产混凝土和硅酸钙建筑产品用机械.安全性.生产预制加筋产品的固定和移动设备

1.1 This part of EN 12629, taken together with EN 12629-1:2000+A1:2010, applies to stationary and mobile equipment for the manufacture of precast reinforced products as defined in Clause 3 and applies to these machines also when used for the manufacture of non-reinforced moulded products. EN 12629-1:2000+A1:2010 specifies general requirements applicable to machines for the manufacture of constructional products from concrete and calcium–silicate. This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific to the machines it covers. 1.2 This document applies to the modules comprising production machines (with or without turnover demoulding) for the manufacturing of reinforced moulded products as shown below and illustrated in informative Annexes A and B. These machines are designed to perform the following cyclic operations: ? manufacturing by vibration and even compression (oiling, mould feeding – concrete + reinforcement –, vibration, floating, interlocking, turnover, removing from mould); ? storage of moulds and pallet boards for concrete hardening; ? products destacking and packaging; ? moulds and pallet boards return to the manufacturing module. Any of these operations may be manual, semi-automatic or automatic. This document deals with automatic and semi-automatic operations of modules A and C and with automatic operations of module B. 1.3 !This European Standard deals with all significant hazards pertinent to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. 1.4 This document is not applicable to stationary and mobile equipment for the manufacture of precast products, which are manufactured before the date of publication of this document by CEN.

Machines for the manufacture of constructional products from concrete and calcium-silicate. Safety. Stationary and mobile equipment for the manufacture of precast reinforced products

JC/T 728-2005 水泥标准筛和筛析仪

本标准规定了水泥标准筛和筛析仪的分类、结构、技术要求、检验方法、检验规则以及标志、包装和运输等内容。 本标准适用于筛析法测定水泥细度的标准筛和筛析仪，以及指定采用本标准测定其他粉状物料细度的标准筛和筛析仪。

Cement standard sieves and sieving apparatus

JC/T 967-2005 混凝土瓦成型机

本标准规定了混凝土瓦成型机的术语、产品分类、技术要求、试验方法、检验规则、标志、包装、贮存和运输。 本标准适用于采用挤压成型工艺生产并符合JC 746-1999要求的混凝土瓦的成型机(以下简称瓦机)。模压式成型机可相应参照执行。

Extruding machine bars for concrete tiles

JC 982-2005 砖瓦焙烧窑炉

本标准规定了砖瓦焙烧窑炉的术语和定义、分类、技术要求、检验方法、检验规则、质量评定、标志和标签以及包装、运输和贮存。 本标准适用于用于普通砖、多孔砖、空心砖、装饰砖和空心砌块等产品的烧结、烧成温度在1200℃以下的热工设备。其它类似工况的工业窑炉亦可参考使用。

Kilm for brick tile

JC/T 681-2005 行星式水泥胶砂搅拌机

本标准规定了行星式水泥胶砂搅拌机(以下简称胶砂搅拌机)的结构和类型、技术要求、检验方法、检验规则、标志及包装等内容。 本标准适用于按GB/T 17671-1999测定水泥胶砂强度及其它指定采用本标准的胶砂搅拌机。

Mixer for mixing mortars

JC/T 682-2005 水泥胶砂试体成型振实台

本标准规定了水泥胶砂试体成型振实台(以下简称振实台)的基本结构、技术要求、检验方法、检验规则、以及标志和包装等内容。 本标准适用于按GB/T 17671-1999测定水泥胶砂强度及其它指定采用本标准的胶砂振实台。

Jolting table for compacting mortars specimen

JC/T 683-2005 40mm×40mm水泥抗压夹具

本标准规定了40mm×40mm水泥抗压夹具(以下简称抗压夹具)的结构与类型、技术要求、检验方法、检验规则以及标志和包装等内容。 本标准适用于按GB/T 17671-1999水泥胶砂强度试验方法测定水泥胶砂强度的抗压夹具及其他指定采用本标准的抗压夹具。

40mm×40mm Jig for cement compressive strength test machine

JC/T 729-2005 水泥净浆搅拌机

本标准规定了水泥净浆搅拌机(以下简称搅拌机)的结构和类型、技术要求、检验方法、检验规则以及标志和包装等内容。 本标准适用于按GB/T 1346-2001水泥标准稠度用水量、凝结时间、安定性检验方法及其他试验方法所用的制备水泥净浆的搅拌机。

Mixer for cement paste

JC/T 727-2005 水泥净浆标准稠度与凝结时间测定仪

本标准规定了水泥净浆标准稠度与凝结时间测定仪的结构、技术要求、检验方法、检验规则、标志、包装与运输。 本标准适用于按GB/T 1346《水泥标准稠度用水量、凝结时间、安定性检验方法》进行的水泥标准稠度用水量和凝结时间试验用测定仪。

Apparatus for determining normal consistency and setting time of cement paste

JC/T 723-2005 水泥胶砂振动台

本标准规定了水泥胶砂振动台(简称振动台)的基本结构、技术要求、检验方法、检验规则、包装、标志与随机文件等。 本标准适用于按GB/T 17671-1999《水泥胶砂强度检验方法（ISO法）》进行胶砂成型的振实台。

Cement mortar vibration compaction equipment

JC/T 724-2005 水泥胶砂电动抗折试验机

本标准规定了电动抗折试验机(以下简称抗折机)的结构、技术要求、检验方法、检验规则以及标志和包装等内容。 本标准适用于检验水泥胶砂40mm×40mm×160mm棱柱试体抗折强度的试验机。

Electrically driven flexure testing device for strength of cement mortar

JC/T 726-2005 水泥胶砂试模

本标准规定了水泥胶砂试模(以下简称试模)的基本结构、技术要求、检验方法、检验规则以及标志和包装等。 本标准适用于GB/T 17671-1999水泥胶砂强度试验方法中成型用试模。

Mould for cement mortars

DIN EN 14406:2004 混凝土结构的保护和维修用产品和系统.试验方法.膨胀率和膨胀发展的测定

This document describes a test method to determine the expansion ratio and rate of injection products intended for ductile filling of wet cracks, voids and interstices.#,,#

Products and systems for the protection and repair of concrete structures - Test methods - Determination of the expansion ratio and expansion evolution; German version EN 14406:2004

DIN EN 14117:2004 混凝土结构的保护和维修用产品和系统.试验方法.粘性注入产品的流出时间测定

This document describes a test method for determining the time of efflux of cementitious injection products, based on the measurement of the time taken for a standard volume of the product to flow through a standardised cone (Marsh cone). This time of efflux is a measure of the viscosity of cementitious injection products.#,,#

Products and systems for the protection and repair of concrete structures - Test methods - Determination of time of efflux of cementitious injection products; German version EN 14117:2004

DIN EN 14498:2004 混凝土结构的保护和维修用产品和系统.试验方法.空气干燥与储水循环后注入产品的体积和重量的变化

This document describes a test method to determine the volume and weight changes of injection products used for swelling fitted filling of cracks, voids and interstices after air drying and water storage cycles.#,,#

Products and systems for the protection and repair of concrete structures - Test methods - Volume and weight changes of injection products after air drying and water storage cycles; German version EN 14498:2004

DIN EN 14497:2004 混凝土结构的保护和维修用产品和系统.试验方法.过滤稳定性的测定

Products and systems for the protection and repair of concrete structures - Test methods - Determination of the filtration stability; German version EN 14497:2004

DIN EN 12618-3:2004 混凝土结构的保护和维修用产品和系统.试验方法.第3部分:带或不带热循环的注入产品的粘性测定.倾斜剪切法

This document describes the method for determining the slant shear bond strength of all injection products intended to restore the integrity of cracked concrete and covered by prEN 1504-5. The test may be performed upon cracks injected in the dry, damp, wet or with water flowing through them. It should always be carried out after the appropriate period of curing under the standard conditions of test detailed below, but may additionally be performed upon a further set of specimens after a period of artificial ageing by termal cycling. Whilst the testing of the repaired crack is normally by short term static load, it may also be performed as a creep test by long term static load, or as a dynamic test by the application of a cyclic load.#,,#

Products and systems for the protection and repair of concrete structures - Test methods - Part 3: Determination of the adhesion of injection products, with or without thermal cycling - Slant shear method; German version EN 12618-3:2004

DIN EN 12637-1:2004 混凝土结构的保护和维修用产品和系统.试验方法.注入产品的兼容性.第1部分:与混凝土的兼容性

This document describes the method for determining the compatibility with concrete of polyurethane injection products, or other elastic injection products likely to be sensitive to the effects of the alkalis in concrete. This document describes the reference procedure. In the case of polyurethane products, this method is only suitable for final injection products (i.e. not water-stopping foams).

Products and systems for the protection and repair of concrete structures - Test methods - Compatibility of injection products - Part 1: Compatibility with concrete; German version EN 12637-1:2004

DIN EN 12618-2:2004 混凝土结构的保护和维修用产品和系统.试验方法.第2部分:带或不带热循环的注入产品的粘性测定.抗拉粘结强度测定粘性

Products and systems for the protection and repair of concrete structures - Test methods - Part 2: Determination of the adhesion of injection products, with or without thermal cycling - Adhesion by tensile bond strength; German version EN 12618-2:2004

DIN EN 12617-2:2004 混凝土构件的保护和维修用产品和系统.试验方法.第2部分:基于高聚物粘合剂的裂缝注入产品的收缩率

This document describes a method for determining the volumetric shrinkage of products formulated with thermosetting polymer binders, mainly epoxy and polyester binders, that cure at ambient temperature or below. This method is adapted for crack injection products formulated with polymer thermosetting binder.

Products and systems for the protection and repair of concrete structures - Test methods - Part 2: Shrinkage of crack injection products based on polymer binder: volumetric shrinkage; German version EN 12617-2:2004