Q92 水泥与水泥制品设备 标准查询与下载

JC/T 878.4-2010 水泥工业用硬齿面减速机 第4部分：立式磨机减速机

JC/T 878的本部分规定了立式磨机减速机的分类与标记、要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于水泥工业用硬齿面减速机中的立式磨机减速机，其他行业可参照使用。

Case-hardened reducer used in cement industry Part 4:Reducer for vertical roller mill

JC/T 878.2-2010 水泥工业用硬齿面减速机 第2部分：边缘传动减速机

JC/T 878的本部分规定了水泥工业用硬齿面边缘传动磨机减速机的分类与标记、要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于水泥工业用硬齿面减速机中的边缘传动磨机减速机，其他行业可参照使用。

Case-hardened reducer used in cement industry Part 2:reducer for side drive tube mill

JC/T 878.3-2010 水泥工业用硬齿面减速机 第3部分：窑用减速机

JC/T 878的本部分规定了窑用机减速机的分类与标记、要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于水泥工业用硬齿面减速机中的窑用机减速机，其他行业可参照使用。

Case-hardened reducer used in cement industry Part 3:reducer for rotary kiln

JC/T 691-2010 高铬铸铁衬板

本标准规定了高铬铸铁衬板的术语和定义、产品分类、技术要求、试验方法、检验规则、标志、包装、运输和贮存等。 本标准适用于建材工业用水泥管磨机高铬铸铁衬板。其他行业用高铬铸铁衬板及过流亦可参照采用。

High chromium cast irons liner

JC/T 878.5-2010 水泥工业用硬齿面减速机 第5部分：辊压机用减速机

JC/T 878的本部分规定了辊压机用减速机的分类与标记、要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于水泥工业用硬齿面减速机中的辊压机用减速机，其他行业可参照使用。

Case-hardened reducer used in cement industry Part 5:Reducer for rolling press

JC/T 455-2009 水泥生料球性能测定方法

本标准规定了水泥生料球的水分、料球级配、耐压力、堆积密度、表观密度、生料密度、堆积空隙率、孔隙率、高温爆破率、冲击破损率、干球磨损率、高温收缩率的测定方法和生料球性能评价。 本标准规定了料球强度仪和改制维卡仪两种测定料球强度的方法，有争议时以专用料球强度测定仪方法为准。 本标准适用于半干法水泥生产工艺中生料球性能的测定。

Methods for performance-measuring of raw meal nodule of cement

JC/T 731-2009 机械化水泥立窑热工测量方法

本标准规定了生产硅酸盐水泥熟料的各类型机械化水泥立窑系统的热工测量方法。 本标准适用于生产硅酸盐水泥熟料的各类机立窑系统的热工测量。

Methods for heat-measuring of mechanical cement shaft kilns

JC/T 732-2009 机械化水泥立窑热工计算

本标准规定了生产硅酸盐水泥熟料的各类型机械化立窑系统的热工计算方法。 本标准适用于生产硅酸盐水泥熟料的各类型机械化立窑系统的热工计算。普通立窑的热工计算也可参照本标准进行。

Calculation of heat balance for mechanical cement shaft kilns

ASTM C511-09 水硬水泥和混凝土试验用搅拌室、湿气箱、湿气室和水贮存罐标准规范

1.1 This specification includes requirements for mixing rooms where paste and mortar specimens are prepared; and for moist cabinets, moist rooms, and water storage tanks where paste, mortar, and concrete specimens are stored. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. Values in SI units shall be obtained by measurement in SI units or by appropriate conversion, using the Rules for Conversion and rounding given in Standard IEEE/ASTM SI 10, of measurements made in other units. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes

JG 238-2008 混凝土标准养护箱

本标准规定了混凝土试件标准养护箱(以下简称养护箱)的分类、规格与标记、使用条件和材料、要求、试验方法、检验规则及标志、包装和运输贮存等要求。 本标准适用于混凝土试件标准养护的养护箱。

Standard curing chamber for concrete

EN 13102:2005+A1:2008 陶瓷机器.安全性.细粘土砖的装卸

This European Standard applies to: machines for stacking or dehacking fired or unfired fine clay wall tiles and floor tiles on/from fixed or movable supports (see Figure A.1); machines for loading or unloading fired or unfired fine clay wall tiles and floor tiles into/from containers (see Figures A.2 and A.4); machines for loading or unloading fired or unfired fine clay wall tiles and floor tiles on/from stackable frames (see Figure A.3). This European Standard deals with the significant hazards, hazardous situations and events relevant to ceramic machines for loading and unloading of fine clay tiles, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard does not deal with noise. This European Standard deals with the preventive measures to minimise these hazards arising from the commissioning, the operation and maintenance. The interface with the transport system for stacks, containers is covered by this European Standard for some examples not for all possibilities (see e. g. 5.6.4, 5.6.7). This European Standard is not applicable to: machines for setting and dehacking of split tiles and roof tiles; auxiliary machinery such as vacuum generators. This European Standard is not applicable to machines, which are manufactured before the date of publication of this European Standard by CEN.

Ceramic machines - Safety - Loading and unloading of fine clay tiles

EN 13367:2005+A1:2008 陶瓷机械.安全性.传送平台和传送车

This European Standard applies for the design, installation and commissioning of transfer platforms and cars and ancillary devices for the process related transport of ceramic material on rails. The rails, which are considered to be horizontal and the movement of vehicles in equipment and machinery connected with the process related transport such as kilns, dryers, collector scaffolds, machinery for loading and unloading are also covered. This European Standard deals with all significant hazards, hazardous situations and events relevant to transfer platforms and cars, when they are used as intended and under the conditions foreseen by the manufacturer (see Clause 4). Noise is not a significant hazard. This document deals with the preventive measures to minimise these hazards which can arise during commissioning, the operation and maintenance. This European Standard is not applicable to: Kilns and dryers (see EN 746-1:1997), machinery for setting and dehacking of heavy clay and refractory, products and machinery for loading and unloading of fine clay tiles; Retrial, packaging and storage of finished products; Transport of cars with not rail mounted equipment e. g. with driverless trucks (see EN 1525:1997); Transfer platforms and cars which are driven by human power. This European Standard is not applicable to transfer platforms and cars and ancillary devices which are manufactured before the date of publication of this European Standard by CEN.

Ceramic machines - Safety - Transfer platforms and cars

DIN EN 12151:2008 混凝土和灰浆生产用机械和设备.安全要求

1.1 This document applies for machinery and plants for the preparation of concrete and mortar as defined in 3.1. This document specifies the requirements for the design of: a) hatching and mixing installations for concrete and mortar; b) powered mixers for concrete and mortar, including for storage and handling; c) waste fresh concrete reprocessing plant. It does not include requirements relevant to truck mixers. The machinery may be static or it may be capable of being moved to an alternative position. 1.2 This document deals with all significant hazards, hazardous situations and events relevant to machinery and plant for the preparation of concrete and mortar, when they are used as intended and under the conditions foreseen by the manufacturer (see Clause 4). The exceptions are explosion hazards when using flammable or explosive materials that are significant but not dealt with. This document specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. Maintenance is dealt with but not noise during maintenance. 1.3 This document is not applicable to machinery and plants which are manufactured before the date of publication of this document by CEN.

Machinery and plants for the preparation of concrete and mortar - Safety requirements; English version of DIN EN 12151:2008-05

JC/T 1031-2007 蒸压加气混凝土模具

本标准规定了蒸压加气混凝土模具的产品分类、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于蒸压工艺生产加气混凝土的模具（以下简称模具）。

Mould for autoclaved aerated concrete

JC/T 1032-2007 预应力钢筒混凝土管和三阶段管用缠丝机

本标准规定了预应力钢筒混凝土管和三阶段管用缠丝机的分类、要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于预应力钢筒混凝土管（GB/T 19685-2005）和三阶段管（GB 5696-2006）用缠丝机（以下简称：缠丝机）。其他形式的混凝土管用缠丝机可参照执行。

Wire winder for PCCP and three-stage pipe

JC/T 877-2007 预应力钢筒混凝土管和三阶段管用辊射机

本标准规定了预应力钢筒混凝土管和三阶段管用辊射机的分类、要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于预应力钢筒混凝土管（GB/T 19685-2005）和三阶段管用（GB 5696-2006）辊射机（以下简称辊射机）。

Rolling sprayer for peep and three-stage pipe

JC/T 1033-2007 预应力钢筒混凝土管用钢筒螺旋卷焊机

本标准规定了预应力钢筒混凝土管用钢筒螺旋卷焊机的术语和定义、分类、要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于预应力钢筒混凝土管用钢筒螺旋卷焊机（以下简称：螺旋卷焊机）。其他形式的钢筒焊接机可参照执行。

Welding Machine for Spirally Rolled Steel Cylinder of PCCP

JC/T 358.1-2007 水泥工业用电除尘器 型式与基本参数

JC/T 358的本部分规定了水泥工业用电除尘器（以下简称电除尘器）的型式与基本参数。 本部分适用于处理水泥工业用回转窑、原料磨、熟料冷却机、煤磨、水泥磨和烘干机等尘源设备烟气的电除尘器，也可用于其他行业同类产品。

Electrostatic precipitator's type and basic technical parameters for cement industry

JC/T 818-2007 回转式水泥包装机

本标准规定了回转式水泥包装机的术语和定义、产品分类、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于叶轮给料回转式水泥包装机及螺旋给料回转式水泥包装机（以下简称包装机），其它回转式水泥包装机亦可参照执行。

Roto packer

JC/T 1034-2007 预应力钢筒混凝土管管模

本标准规定了预应力钢筒混凝土管管模的术语、分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于预应力钢筒混凝土管管模（以下简称管模）。其他预应力管模亦可参照使用。

Mold for prestreesed concrete cylinder pipe