共找到 410 条与 照明与信号设备 相关的标准,共 28 页
The following changes in requirements to the Standard for Low Voltage Lighting Fixtures for Use in Recreational Vehicles, UL 234, are being proposed: 1. New Paragraph 1.3 to include reference to UL 8750 for requirements for LED components and subassemblies 2. Editorial correction to add Fahrenheit equivalent in 28.3(b)
Standard for Safety for Low Voltage Lighting Fixtures for Use in Recreational Vehicles
This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Standard applies to 145 mm nominal headlamp and floodlamp units. To define the dimensional requirements for sealed lighting units and assure their interchangeability.
Requirements for Sealed Lighting Unit for Construction and Industrial Machines
This SAE Standard provides test procedures, performance requirements, and guidelines for center high mounted stop lamps (CHMSL) for use on vehicles less than 2032 mm in overall width.
Central High Mounted Stop Lamp Standard for Vehicles Less than 2032 mm Overall Width
This SAE Standard provides test procedures, requirements, and guidelines for turn signal lamps intended for use on vehicles of less than 2032 mm in overall width.
Turn Signal Lamps for Use on Motor Vehicles Less Than 2032 mm in Overall Width
This SAE Recommended Practice provides test procedures, requirements, and guidelines for the system of optical warning devices used on emergency vehicles.
Minimum Performance of the Warning Light System Used on Emergency Vehicles
Road vehicles - Symbols for controls, indicators and tell-tales; Amendment 1
Portable searchlight with mounting equipment for vehicles, explosion-proof
This SAE Recommended Practice applies to functions of motor vehicle signalling and marking lighting devices which use light emitting diodes (L.E.D.'s) as light sources.This report provides test methods,requirements,and guidelines applicable to the special characteristics of L.E.D lighting devices.This Recommended Practice is in addition to those require for device designed with incandescent light sources.This report is intended to be a guide to standard practice and is subject to change to reflect additional experience and technical advances.
L.E.D. Signal and Marking Lighting Devices
Most signal and marking lighting devices have light sources (bulbs), which can be based on either filament or LED technology. To assure field replacement, it is important that light source types employed be readily available in normal service channels. This document defines the physical, electrical, and photometric characteristics necessary to achieve a proper replacement for popular types of signal and marking light sources. Some of the design characteristics in this document are listed solely for the sake of standardization and are not intended to describe the performance of lighting devices (lamp assemblies) on the vehicle.
Signal and Marking Light Sources
This SAE Standard provides test procedures, requirements, and guidelines for stop lamps intended for use on vehicles of less than 2032 mm in overall width.
Stop Lamps for Use on Motor Vehicles Less Than 2032 mm in Overall Width
This document provided design guidelines, test procedure references, and performance requirements for red and yellow overhead devices on school bus vehicles which are used to alert traffice to stop when passengers are loading and unloading.
School Bus Warning Lamps
Road vehicles -- Symbols for controls, indicators and tell-tales
This SAE Standard covers the general requirements and the test requirements for a flashing warning lamp for agricultural equipment.
Flashing Warning Lamp for Agricultural Equipment
This standard provides test methods and requirements for snowmobile headlamps.
Snowmobile Headlamps
This document provides test methods and requirements for the stop lamp on snowmobiles.
Snowmobile Stop Lamp
The SAE document provides test methods and requirements for tail lamps for snowmobiles.
Snowmobile Tail Lamp (Rear Position Lamp)
To provide specifications for lighting and marking of industrial wheeled equipment whenever such equipment is operated or traveling on a highway.
Lighting and Marking of Industrial Equipment on Highways (Stabilized Type)
This SAE Standard provides test procedures, performance requirements, design guidelines and installation guidelines for front fog lamps. RATIONALE: Updated section 6.4 Color to esclude the color between white and selective yellow to harmonize with ECE R19. Changed from.....shall be white to selective yellow....to.....shall be white or selective yellow.
Front Fog Lamps
This SAE Standard provides test procedures, performance requirements and guidelines for auxiliary high beam lamps.
Auxiliary High Beam Lamps (Stabilized Type)
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号