T60 拖拉机综合 标准查询与下载
共找到 249 条与 拖拉机综合 相关的标准，共 17 页
本标准规定了拖拉机传动系的术语、定义和对应的英文名称。 本标准适用于拖拉机。
Tractor terminology--Transmission system
- ICS
- 65.060.10
- CCS
- T60
- 发布
- 1995-12-14
- 实施
- 1996-06-01
本标准规定了拖拉机液压悬挂系及牵引、拖挂装置的术语、定义和对应的英文名称。 本标准适用于拖拉机。
Tractor terminology--Hydraulic hitch system and drawbar、hook
- ICS
- 65.060.10
- CCS
- T60
- 发布
- 1995-12-14
- 实施
- 1996-06-01
本标准规定了拖拉机转向系的术语、定义和对应的英文名称。 本标准适用于拖拉机。
Tractor terminology--Steering system
- ICS
- 65.060.10
- CCS
- T60
- 发布
- 1995-12-14
- 实施
- 1996-06-01
本标准规定了拖拉机驾驶室、驾驶座和覆盖件等的术语、定义和对应的英文名称。 本标准适用于拖拉机。
Tractor terminology--Cab、seat and sheet metal
- ICS
- 65.060.10
- CCS
- T60
- 发布
- 1995-12-14
- 实施
- 1996-06-01
本标准规定了农林拖拉机的动态环境噪声和驾驶员操作位置处噪声限值。 本标准适用于轮式拖拉机、履带拖拉机和手扶拖拉机。
Noise limitation for tractors
- ICS
- 65.060.10
- CCS
- T60
- 发布
- 1995-11-16
- 实施
- 1996-05-01
Tractors and machinery for agriculture and forestry—Technical means for ensuring safety—Part 3:Tractors
- ICS
- 65.060.10
- CCS
- T60
- 发布
- 1994-12-27
- 实施
- 1995-07-01
本标准规定了使用农业拖拉机时防止发生意外事故的准则和设计拖拉机时应达到的合理参数，以保证驾驶员和参加正常作业、维护保养人员的人身安全。 本标准适用于农业轮式和履带拖拉机，其它类型拖拉机也可参照采用。
Tractors and machinery for agriculture and forestry--Technical means for ensuring safety--Part 3:Tractors
- ICS
- 65.060.10
- CCS
- T60
- 发布
- 1994-12-27
- 实施
- 1995-07-01
本标准规定了农业轮式拖拉机驾驶员全身振动的测量方法，其中包括对仪器、测量地点的特征和加权频率分析所作的规定。 本标准适用于田间、道路及人工试验跑道条件下，对农业轮式拖拉机驾驶员全身振动的测量。 本标准不适用于具有特殊用途和结构的拖拉机，如三轮拖拉机、手扶拖拉机、高地隙拖拉机和坡地拖拉机等。 注：本标准未考虑通过底板或脚踏板传到脚上，以及通过操纵杆或转向盘传到手上的振动。
Agricultural wheeled tractors--Measurement of whole-body vibration of the operator
- ICS
- 65.060.10
- CCS
- T60
- 发布
- 1989-03-31
- 实施
- 1990-01-01
本标准适用于至少具有两轴的充气轮胎拖拉机，可带或不带履刺附件，其质量为800～6000kg，对于静载试验可达到15000kg，后轮最小轮距一般应大于1150mm。 本标准不适用于葡萄园用窄型拖拉机，低建筑物下与果园用低轮廓拖拉机，高架式拖拉机和某些林业机械。
Agricultural and forestry wheeled tractors--Protective structures--Test method in the strength and acceptance conditions
- ICS
- 65.060.10
- CCS
- T60
- 发布
- 1986-12-30
- 实施
- 1987-09-01
Agricultural tractors. Hydraulic pressure for implements
- ICS
- 65.060.01
- CCS
- T60
- 发布
- 2021-08-06
- 实施
- 2021-08-06
This document specifies the characteristics of the hydraulic pressure from agricultural tractors to connect hydraulic devices on implements, to permit interchangeable use of various types of implements using remote cylinders and other hydraulic devices. It applies to agricultural tractors intended for interchangeable implements.
Agricultural tractors - Hydraulic pressure for implements
- ICS
- 65.060.01
- CCS
- T60
- 发布
- 2021-07-00
- 实施
Wheeled tractor energy efficiency rating evaluation
- ICS
- 65.060.10
- CCS
- T60
- 发布
- 2019-08-01
- 实施
- 2019-11-01
Evaluation method for technical level of agricultural wheel tractors
- ICS
- 65.060.01
- CCS
- T60
- 发布
- 2018-03-15
- 实施
- 2018-06-01
This document specifies test procedures for determining the power available at the drawbar on agricultural tractors of the wheeled, track-laying or semi-track-laying type.
Agricultural tractors - Test procedures - Part 9: Power tests for drawbar
- ICS
- 65.060.10
- CCS
- T60
- 发布
- 2018-02-01
- 实施
This document specifies test procedures for determining the power available at the power take-off (PTO) on agricultural tractors of the wheeled, track-laying or semi-track-laying type.
Agricultural tractors - Test procedures - Part 1: Power tests for power take-off
- ICS
- 65.060.10
- CCS
- T60
- 发布
- 2018-02-01
- 实施
This document gives terms and definitions for use in the other parts of ISO 789. Annex A provides a specimen test report for all parts of ISO 789.
Agricultural tractors - Test procedures - Part 13: Vocabulary and specimen test report
- ICS
- 65.060.10
- CCS
- T60
- 发布
- 2018-02-01
- 实施
This document specifies test procedures for determining the lifting capacity of rear-mounted threepoint linkage systems: a) the maximum vertical force which can be exerted by the hydraulic lift at the lower hitch points throughout their full range of movement; b) the maximum vertical force which can be exerted by the hydraulic lift, at a point 610 mm to the rear of the hitch points on a frame attached to the three-point linkage, throughout its full range of movement. NOTE 1 A static test provides an adequate comparison between tractors. The test results are used only as a means of comparing tractors and not as a way of recommending the size of an implement which can be carried by the tractor. NOTE 2 systems. This test procedure can be used to determine the lifting capacity of front-mounted three-point hitch
Agricultural tractors - Test procedures - Part 2: Rear three-point linkage lifting capacity
- ICS
- 65.060.10
- CCS
- T60
- 发布
- 2018-02-01
- 实施
This document specifies the dimensions, characteristics, and positioning of Speed Identification Signs (SIS). These signs indicate the maximum equipment ground speed, based on the ground speed design capability, for an agricultural vehicle. A rear-facing SIS is visible to other operators on public roads approaching the equipment from behind. A forward-facing SIS, mounted on the front of towed equipment, alerts operators of the towing vehicle of the maximum specified ground speed capabilities at which the equipment combination can be operated. This document is applicable to self-propelled, semi-integral and towed equipment moving on public roads.
Tractors and machinery for agriculture and forestry - Speed Identification Sign (SIS)
- ICS
- 65.060.10
- CCS
- T60
- 发布
- 2017-11-01
- 实施
本标准规定了拖拉机用润滑油品种、规格的选用。 本标准适用于拖拉机。
Type and specifications of lubricants for tractors
- ICS
- 65.060.10
- CCS
- T60
- 发布
- 2016-04-05
- 实施
- 2016-09-01
