T60 拖拉机综合 标准查询与下载

SAE J1824-2009 座钳式集材拖拉机的规范定义

This SAE Recommended Practice identifies and defines the specifications most commonly used to describe high speed steel track and articulated rubber- tired clam bunk skidders. The illustrations used are not intended to be descriptive of any existing machine or dictate a combination needed for a particular logging situation. The dimensions indicated are basic and may be supplemented by the individual manufacturer. The purpose of this SAE document is to establish a uniform method of identifying and defining the specifications most commonly used to compare various models of this type of equipment.

Specification Definitions Clam Bunk Skidder

ISO 11001-3:2009 农业轮式拖拉机和机具.三点挂钩式耦合器.第3部分:链式耦合器

Agricultural wheeled tractors and implements - Three-point hitch couplers - Part 3: Link coupler

ISO 26322-1:2008 农业和林业用拖拉机.安全性.第1部分:拖拉机标准

Tractors for agriculture and forestry - Safety - Part 1: Standard tractors

ISO 12003-2:2008 农业和林业用拖拉机.窄轨距轮式拖拉机的翻车保护结构.第2部分:后部安装的ROPS

This part of ISO 12003 specifies procedures for both the static and dynamic testing of roll-over protective structures (ROPS) rear-mounted on narrow-track wheeled agricultural and forestry tractors. It defines the clearance zone and acceptance conditions for rigid or tiltable, rear, two-post roll bar, frame and cab ROPS, and is applicable to tractors so equipped having the following characteristics. -- A ground clearance of not more than 600 mm beneath the lowest points of the front- and rear-axle housings (not considering lower points on the axle differential). -- A fixed or adjustable minimum track width of one of the two axles of less than 1 150 mm when fitted with the widest specified tyres, and with the overall width of the other axle being less than that of the first axle. .... A mass greater than 600 kg but less than 3 000 kg, unladen, including the ROPS and tyres of the largest size recommended by the manufacturer.

Agricultural and forestry tractors - Roll-over protective structures on narrow-track wheeled tractors - Part 2: Rear-mounted ROPS

ISO 12003-1:2008 农业和林业用拖拉机.窄轨距轮式拖拉机的翻车保护结构.第1部分:前部安装的ROPS

This part of ISO 12003 specifies procedures for both the static and dynamic testing of roll-over protective structures (ROPS) front-mounted on narrow-track wheeled agricultural and forestry tractors. It defines the clearance zone and acceptance conditions for rigid or tiltable, front, two-post ROPS, including any associated rear fixtures, and is applicable to tractors so equipped having the following characteristics. -- A ground clearance of not more than 600 mm beneath the lowest points of the front- and rear-axle housings (not considering lower points on the axle differential). A fixed or adjustable minimum track width of one of the two axles of less than 1 150 mm when fitted with the widest specified tyres. It is understood that the axle mounted with the wider tyres is set at a track width of not more than 1 150 mm. It shall be possible to set the track width of the other axle in such a way that the outer edges of the narrower tyres do not extend beyond the outer edges of the tyres of the other axle. Where the two axles are fitted with rims and tyres of the same size, the fixed or adjustable track width of the two axles shall be less than 1 150 mm. -- A mass greater than 600 kg but less than 3 000 kg, unladen, including the ROPS and tyres of the largest size recommended by the manufacturer.

Agricultural and forestry tractors - Roll-over protective structures on narrow-track wheeled tractors - Part 1: Front-mounted ROPS

ISO 4252:2007 农业拖拉机.操作者的工作位置、入口和出口.尺寸

This International Standard specifies the design dimensions of agricultural tractors having a minimum track width exceeding in respect of a) the minimum dimensions of their access doorways, b) the number, location and minimum dimensions of their emergency exits, and c) their minimum internal clearance dimensions.

Agricultural tractors - Operator's workplace, access and exit - Dimensions

KS B ISO 500-3:2007 农用拖拉机.后置式动力输出1、2、3型.第3部分:主PTO尺寸和PTO的花键尺寸及位置

이 규격은 농업용 트랙터의 후방 동력취출장치 형식 1, 2, 3에 대한 제작 조건과 위치를

Agricultural tractors-Rear-mounted power take-off types 1, 2 and 3-Part 3:Main PTO dimensions and spline dimensions, location of PTO

KS B ISO 500-1:2007 农用拖拉机.后置式动力输出1、2、3型.第1部分:主挡板和余隙的一般规范、安全要求和尺寸

이 규격은 차륜 거리가 1 150 mm 이상인 농업용 트랙터의 후방 동력취출장치 형식 1,

Agricultural tractors-Rear-mounted power take-off types 1, 2and 3-Part 1:General specifications, safety requirements,dimensions for master shield and clearance zone

KS B ISO 5008:2007 农用轮式拖拉机和田间作业机械.操作员全身振动的测量

1.1 이 규격은 농업용 차륜형 트랙터 또는 포장 기계의 운전자가 표준 시험 주행로에서 운

Agricultural wheeled tractors and field machinery－Measurement of whole-body vibration of the operator

KS B ISO 500-2:2007 农用拖拉机.后置式动力输出1、2、3型.第2部分:窄轮距拖拉机主挡板和余隙的尺寸

이 규격은 농업용 협폭 트랙터(차륜 거리가 1 150 mm 이하)의 후방 동력취출장치 형식

Agricultural tractors－Rear-mounted power take-off types 1, 2 and 3－Part 2：Narrow-track tractors, dimensions for master shield and clearance zone

NY 346-2007 拖拉机驾驶证证件

本标准规定了拖拉机驾驶证证件的式样、规格、印刷、制作质量、印章、检验方法和验收规则、标志、包装、运输和签注。 本标准适用于拖拉机驾驶证证件的制作和质量检验。

Tractor Driving License

NY 1371-2007 联合收割机驾驶证证件

本标准规定了联合收割机驾驶证证件的式样、规格、印刷、制作质量、印章、检验方法和验收规则、标志、包装、运输和签注。 本标准适用于联合收割机驾驶证证件的制作和质量检验。

Combine Driving License

NY/T 1357-2007 拖拉机用压燃式发动机排气污染物排放质量评价技术规范

本标准规定了拖拉机用压燃式发动机排气污染物的排放限值、测量条件、测量方法、判定规则。 本标准适用于拖拉机用压燃式发动机排气污染物的质量评定。

Technical Specincationof Emission Quality Evaluation for Exhaust Pollutants from Compression Ignition Engines of Tractor

DIN EN ISO 5674:2007 农林业用拖拉机和机械.动力输出传动轴.强度和磨损试验及验收标准

This International Standard specifies laboratory tests for determining the strength and wear resistance of guards for power take-off (PTO) drive-shafts on tractors and machinery used in agriculture and forestry, and their acceptance criteria. It is intended to be used in combination with ISO 5673. It is applicable to the testing of PTO drive-shaft guards and their restraining means. It is not applicable to the testing of guards designed and constructed to be used as steps.

Tractors and machinery for agriculture and forestry - Guards for power take-off (PTO) drive-shafts - Strength and wear tests and acceptance criteria (ISO 5674:2004, corrected version 2005-07-01); German version EN ISO 5674:2006

ISO 23206:2005/cor 1:2007 农用轮式拖拉机及附件.前端式装载机.附件用支架.技术勘误1

This standard is Agricultural wheeled tractors and attachments — Front loaders — Carriages for attachments TECHNICAL CORRIGENDUM 1

Agricultural wheeled tractors and attachments - Front loaders - Carriages for attachments; Technical Corrigendum 1

NF U03-024-1/A1:2007 农用拖拉机和自行式设备.灰尘和植物保健产品的空气净化室性能.要求和试验.第1部分:空气净化装置

Agricultural tractors and self-propelled equipment - Performance of air purified cabs with respect to dust and plant health products - Requirements and tests - Part 1 : air purification devices.

BS ISO 3776-1:2007 农用拖拉机和机械.安全带.停放地点要求

This part of ISO 3776 specifies the location, relative position and threaded hole dimensions of the anchorages for pelvic restraint (seat) belt assemblies intended to be used by the operators of agricultural tractors and self-propelled machinery.

Tractors and machinery for agriculture - Seat belts - Anchorage location requirements

SANS 1468:2006 有轮农业或林业用拖拉机用防倾翻结构（静态试验）（包括经EEC第82/953号指令修订的关于有轮农用和林业用拖拉机的防倾翻保护结构的EEC第79/622号指令）

Covers the performance requirements and a static test for roll-over protection structures of agricultural or forestry tractors. Does not cover roll-over protection structures intended for special purpose tractors.

Roll-over protection structures for wheeled agricultural or forestry tractors (static testing)(Incorporating EEC Directive 79/622, as amended by EEC Directive 82/953, relating to the roll-over protection structures of wheeled agricultural or forestry trac

BS ISO 500-2:2004 农用拖拉机.后置式动力输出1、2、3型.窄轮距拖拉机主挡板和余隙的尺寸

This part of ISO 500 specifies the dimensions of the master shield and clearance zones for rear-mounted power take-offs (PTO) of types 1 and 2 on narrow-track (track width 1 150 mm or less) agricultural tractors.

Agricultural tractors - Rear-mounted power take-off types 1, 2 and 3. Narrow-track tractors, dimensions for master shield and clearance zone

ANSI/ASABE/ISO 14269-5:2006 拖拉机和自进式农林机械.操作室环境.第5部分:增压系统试验方法

This standard specifies a test procedure which will provide for uniform measurement of the pressurization inside an operator enclosure of tractors and self-propelled machines for agriculture and forestry when equipped with a ventilation system.

Tractors and self-propelled machines for agriculture and forestry - Operator enclosure environment, Part 5: Pressurization system test method