N64 实验室用玻璃、陶瓷、塑料器皿 标准查询与下载

BS EN ISO 4788:2005 实验室玻璃器皿.分度量筒

This International Standard specifies dimensions, material and constructional and metrological requirements of graduated measuring cylinders of tall form (Type 1a and Type 1b) and of squat form (Type 2). All types are suitable for general laboratory use. The specifications in this International Standard are in conformity with the principles of design and construction of volumetric glassware given in ISO 384.

Laboratory glassware - Graduated measuring cylinders

BS EN ISO 385:2005 实验室玻璃器皿.滴定管

This International Standard provides metrological and construction requirements for an internationally acceptable series of burettes, suitable for general laboratory purposes. The details specified are in accordance with the principles of design and construction of volumetric glassware given in ISO 384. NOTE For piston burettes, see ISO 8655-3.

Laboratory glassware - Burettes

NF B35-797:2005 实验室玻璃器皿.锥形磨接口烧瓶

Laboratory glassware - Boiling flasks with conical ground joints.

ISO 4788:2005 实验室玻璃器皿.分度量筒

This International Standard specifies dimensions, material and constructional and metrological requirements of graduated measuring cylinders of tall form (Type 1a and Type 1b) and of squat form (Type 2). All types are suitable for general laboratory use. The specifications in this International Standard are in conformity with the principles of design and construction of volumetric glassware given in ISO 384.

Laboratory glassware - Graduated measuring cylinders

SANS 1108:2005 玻璃试管

Covers glass test tubes of two types (i.e. rimmed and rimless) for use in laboratories for blood collection purposes and for general purpose use. Specifies requirements for material, dimensions, construction, freedom from defects, packing and marking.

Glass test tubes

ISO 385:2005 实验室玻璃器皿.滴定管

This International Standard provides metrological and construction requirements for an internationally acceptable series of burettes, suitable for general laboratory purposes. The details specified are in accordance with the principles of design and construction of volumetric glassware given in ISO 384. NOTE For piston burettes, see ISO 8655-3.

Laboratory glassware - Burettes

DIN EN ISO 4797:2005 实验室玻璃器皿.锥形磨接口烧瓶

Laboratory glassware - Boiling flasks with conical ground joints (ISO 4797:2004); German version EN ISO 4797:2004

BS EN ISO 4797:2005 实验室玻璃器皿.锥形磨口接头烧瓶

This International Standard specifies requirements for an internationally acceptable series of boiling flasks with conical ground joints for general laboratory purposes.

Laboratory glassware - Boiling flasks with conical ground joints

ARMY A-A-59784-2005 无碱玻璃布增强

This commercial item description(CID) covers E-Glass cloth used as the reinforcement media in the manufacture of advanced composite materials using infusion processes or hand lay-up.

E-GLASS CLOTH REINFORCEMENT

ASTM D4196-05(2011) 确认膜过滤器的无菌性的标准试验方法

This test method may be employed to check the sterility of commercially procured sterile membrane filters. The test also confirms that sterilized filters have not been contaminated. Additionally, this test may be used to monitor the efficacy of in-house sterilization procedures. Filter packages that have obvious packaging defects should not be tested because sterility may have been compromised.1.1 This test method describes a test to confirm the sterility of either manufacturer presterilized or user-sterilized analytical membrane filters. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. ^

Standard Test Method for Confirming the Sterility of Membrane Filters

ASTM D5417-05 维特曼(Vettermann)转鼓试验仪器操作的标准实施规程

This equipment may be used to bring about the changes in texture on the surface of pile floor covering caused by mechanical action. The acceptance criteria of this practice shall be set by mutual agreement between the purchaser and the supplier. 1.1 This practice describes the equipment and operation of the Vettermann drum tester for testing pile yarn floor covering to produce changes in appearance and color due to changes in surface structure by mechanical action. 1.2 This practice is only applicable for use in testing unused pile floor covering of all types. It is not applicable for use in testing used pile yarn floor coverings. 1.3 The values stated in inch-pound units are to be regarded as the standard for all measurements except mass. The SI (metric) units for all measurements except mass are provided for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Operation of the Vettermann Drum Tester

DIN 12918-4:2004 实验室设备.实验室配件.第4部分:纯气体阀门

Laboratory equipment - Laboratory fittings - Part 4: Valves for pure gases

DIN 12918-3:2004 实验室设备.实验室配件.第3部分:工业气体阀门

Laboratory equipment - Laboratory fittings - Part 3: Valves for technical gases

NF B35-470-1*NF EN 14470-1:2004 防火存储柜.第1部分:易燃液体的安全存储柜

Fire safety storage cabinets - Part 1 : safety storage cabines for flammable liquids.

BS EN ISO 14644-5:2004 洁净室和相关的受控环境.操作

ISO 14644-5:2004 specifies basic requirements for cleanroom operations. It is intended for those planning to use and operate a cleanroom. Aspects of safety that have no direct bearing on contamination control are not considered in this part of ISO 14644 and national and local safety regulations must be observed. This document considers all classes of cleanrooms used to produce all types of products. Therefore, it is broad in application and does not address specific requirements for individual industries. Methods and programmes for routine monitoring within cleanrooms are not covered in detail in this part of ISO 14644 but reference should be made to ISO 14644-2 and ISO 14644-3 for monitoring particles, and ISO 14698-1 and ISO 14698-2 for monitoring micro-organisms.

Cleanrooms and associated controlled environments - Operations

ARMY A-A-52048 B-2004 玻璃管液体温度计 自动显示.轻巧携带型

Abstract. This commercial item description covers a thermometer, graduated in degrees Fahrenheit, for the determination of atmospheric temperatures during surveying operations.

THERMOMETER, SELF-INDICATING, LIQUID-IN-GLASS, POCKET TYPE

ISO 4797:2004 实验室玻璃器皿.锥形磨接口烧瓶

This International Standard specifies requirements for an internationally acceptable series of boiling flasks with conical ground joints for general laboratory purposes.

Laboratory glassware - Boiling flasks with conical ground joints

DLA A-A-52083 C-2004 玻璃纤维绳

The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.

TAPE, LACING AND TYING, GLASS

ASTM C1606-04 瓶罐玻璃器皿的TCLP检验用取样协议的标准试验方法

Sampling of decorated glass containers for the TCLP can vary greatly, resulting from the size and shape of the article relative to the amount of ceramic decoration on the ware. Breaking the glass can cause some of the pieces to have no decoration on them, and others to be heavily decorated and more likely to leach lead and cadmium under the TCLP test. This method provides an effective tool to homogenize the glass containers so that reproducible results can be attained from the TCLP test.1.1 This test method defines the way in which container glassware should be prepared before performing the Toxicity Characteristic Leaching Procedure (TCLP). The method covers the homogenization of the sample, and the selection of a representative portion of the sample to test and get reproducible results.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Standard Test Method for Sampling Protocol for TCLP Testing of Container Glassware

ANSI/IEST/ISO 14644-1:1999 洁净室和相关控制环境.第1部分:空气清洁度的分级

This part of ISO 14644 covers the classification of air cleanliness in cleanrooms and associated controlled environments exclusively in terms of concentration of airborne particles. Only particle populations having cumulative distributions based on threshold (lower limit) sizes ranging from 0, 1 ?m to 5 ?m are considered for classification purposes. This part of ISO 14644 does not provide for classification of particle populations that are outside of the specified particle size range, 0, 1 ?m to 5 ?m. Concentrations of ultrafine particles (particles smaller than 0, 1 ?m) and macroparticles (particles larger than 5 ?m) may be used to quantify these populations in terms of U descriptors and M descriptors, respectively. This part of ISO 14644 cannot be used to characterize the physical, chemical, radiological, or viable nature of airborne particles. Note: The actual distribution of particle concentrations within incremental size ranges normally is not predictable and typically is variable over time.

Cleanrooms and associated controlled environments--Part 1: Classification of air cleanliness