Q62 石膏制品 标准查询与下载

ASTM C1264-14 石膏板产品的抽样, 检验, 报废, 认证, 包装, 标记, 海运, 搬运和储存的标准规范

1.1 This specification covers sampling; inspection; rejection; certification; packaging and marking; and shipping, handling, and storage of gypsum panel products shipped from the manufacturer to distributors, dealers, retailers or other resellers. 1.1.1 This specification does not cover storage or stocking on individual job sites. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Sampling, Inspection, Rejection, Certification, Packaging, Marking, Shipping, Handling, and Storage of Gypsum Panel Products

ASTM C1047-14a 石膏墙板和石膏板基础配件的标准规格

1.1 This specification covers accessories used in conjunction with assemblies of gypsum wallboard and gypsum veneer base to protect edges and corners and to provide architectural features (see Fig. 1). FIG. 1 Accessories for Gypsum Wallboard and Gypsum Veneer Base 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base

ASTM C1789-14 石膏板上手持水分仪校正的标准试验方法

5.1 This Standard Test Method is intended for use in calibrating hand-held meters to accurately read from approximately 30 to 90% ERH. Moisture content is related to the ERH or water activity of a material. 5.2 Hand-held meters provide a rapid means of sampling the moisture content of gypsum boards and panels during manufacture and for field inspection during and after building construction. However, these measurements are inferential, that is, electrical parameters are measured and compared against a calibration curve to obtain an indirect measure of moisture content. The electrical measurements are influenced by the actual moisture content, a number of other gypsum board and panel variables, environmental conditions, the geometry of the measuring probe, and the design of the meter. The maximum accuracy can only be obtained by an awareness of the effect of each parameter on the meter output and correction of readings as specified by these test methods. 5.3 Electrical conductance and dielectric meters are not necessarily equivalent in their readings under the same conditions. When this test method is referenced, the type of meter that is being used must be reported with the relevant ranges for precision and bias as specified in this standard. 5.4 Both types of meters are to be calibrated with respect to ERH as described in this standard. 1.1 This test method applies to the calibration of handheld moisture meters for gypsum board, glass faced gypsum panels and fiber-reinforced gypsum panels by means of electrical conductance and dielectric meters. The test uses wetted test specimens which are dried down in at least 5 steps to determine the moisture content based on the weight loss in comparison to the dry weight. The test also supplies the ERH values for each of the drying steps. 1.2 This test method has not been evaluated for the influence of paint or wall covering materials on the indicated moisture content of a gypsum board or panel substrate. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Calibration of Hand-Held Moisture Meters on Gypsum Panels

ASTM C1047-14 石膏墙板和石膏层板基底用附件的标准规范

1.1 This specification covers accessories used in conjunction with assemblies of gypsum wallboard and gypsum veneer base to protect edges and corners and to provide architectural features (see Fig. 1). 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base

ASTM C1396/C1396M-14 石膏板标准规格

1.1 This specification covers the gypsum boards described in 1.1.1 – 1.1.9.Note 1—Specifications C840, C841, C844 and C1280 contain application procedures for gypsum board. 1.1.1 Gypsum wallboard, designed for use on walls, ceilings, or partitions and that affords a surface suitable to receive decoration. 1.1.2 Predecorated gypsum board, designed for use as the finished surfacing for walls, ceilings, or partitions. 1.1.3 Gypsum backing board, coreboard, and shaftliner board, designed for use as a base in multilayer systems or as a gypsum stud or core in semisolid or solid gypsum board partitions, or in shaft wall assemblies.Note 2—The terms backing board, coreboard, and shaftliner board refer to different end uses. The term gypsum backing board, as used in this specification, shall include gypsum coreboard and gypsum shaftliner board unless otherwise stated. 1.1.4 Water-resistant gypsum backing board, designed primarily to be used as a base for the application of ceramic or plastic tile on walls or ceilings. This product is also suitable for decoration. 1.1.5 Exterior gypsum soffit board, designed for use on exterior soffits and carport ceilings that are completely protected from contact with liquid water. 1.1.6 Gypsum sheathing board, designed for use as sheathing on buildings. 1.1.7 Gypsum base for veneer plaster, designed for use as a base for the application of gypsum veneer plaster. 1.1.8 Gypsum lath, designed for use as a base for the application of gypsum plaster. 1.1.9 Gypsum ceiling board, designed for use on interior ceilings with framing spaced not more than 24 in. [610 mm] on center and that affords a surface suitable to receive water-based texture and other decoration. This product is also suitable for use on interior walls. 1.2 Specifications applicable to all gypsum boards are located in Section 1 – 4 and 13 – 15. Specifications applicable to specific gypsum boards are located in the following sections:  

Standard Specification for Gypsum Board

DB31/T 743-2013 纤维增强脱硫石膏空心大阪

本标准规定了纤维增强脱硫石膏空心大板的术语和定义、外形、分类、规格与标记、原材料、要求、试验方法、检验规则以及标志、包装、运输和贮存。 本标准适用于由脱硫石膏制作的、用作建筑物墙体或建筑施工模板的纤维增强脱硫石膏空心大板。

Fiber reinforced desulfurized gypsum hollow Osaka

BS PAS 109:2013 从废弃石膏板中回收石膏的生产规范

Specification for the production of reprocessed gypsum from waste plasterboard

ASTM C11-13 石膏及相关建筑材料和系统的相关标准术语

1.1 This standard covers terminology relating to gypsum and related building materials and systems. The terms are generically defined. More specific and expanded definitions may appear in appropriate standards.

Standard Terminology Relating to Gypsum and Related Building Materials and Systems

ASTM C471M-13 石膏和石膏制品的化学分析标准试验方法(公制)

17.1 This test method covers the determination of calcium sulfate in gypsum and gypsum products by extraction with ammonium acetate solution. 1.1 These test methods cover the chemical analysis of gypsum and gypsum panel products, including gypsum ready-mixed plaster, gypsum wood-fibered plaster, and gypsum concrete. 1.2 The test methods appear in the following order:   Sections Preparation of Sample 4 Complete Procedure  5 – 16 Alternative Procedure for Analysis for Calcium Sulfate by Ammonium Acetate Method 8201; 17 – 22 Alternative Procedure for Analysis for Sodium Chloride by the Coulometric Method 8201; 23 – 29 Determination of Sand in Set Plaster 30 – 36 Wood-Fiber Content in Wood-Fiber Gypsum Plaster 37 – 39 Optional Procedure for Analysis for Sodium by the Atomic Absorption Method......

Standard Test Methods for Chemical Analysis of Gypsum and Gypsum Products 40;Metric41;

ASTM C318/C318M-13 石膏预制板的标准规格

1.1 This specification covers the minimum requirements for gypsum formboard designed for use as a permanent form for poured-in-place reinforced gypsum concrete roof decks. 1.2 The values stated in either inch-pound units or SI (metric) are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system shall be used independent of the other. Values from the two systems shall not be combined. 1.3 The text of this standard references notes which provide explanatory material. These notes shall not be considered requirements of the standard.

Standard Specification for Gypsum Formboard

ASTM C840-13 石膏板的应用和加工标准规范

1.1 This specification covers the minimum requirements for the methods of application and finishing of gypsum board, including related items and accessories. 1.2 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories. 1.2.1 Where this specification is more stringent (size or thickness of framing: size and spacing of fasteners) than the fire-rated construction, this specification shall govern. 1.3 Where sound control is required for a gypsum board assembly, details of construction shall be in accordance with reports of acoustical tests of assemblies that have met the required acoustical values. 1.4 Unheated spaces above gypsum board ceilings shall be properly ventilated (see Appendix X2). 1.5 The various application systems are located in the following sections: I Application of Single-Ply Gypsum Board to Wood Framing 8199;Members 8 II Application of Two-Ply Gypsum Board to Wood Framing 8199;Members 9 III Application of Gypsum Board by Adhesive Nail-On to 8199;Wood Framing Members 10 IV Semi-Solid Gypsum Board Partitions 11 V Solid Gypsum Board Partitions 12 VI Application of Gypsum Board with Adhesives to Interior 8199;Masonry or Concrete Walls 13 VII Application of Gypsum Board to Rigid Foam Insulation......

Standard Specification for Application and Finishing of Gypsum Board

ASTM C1280-13 外部石膏面板产品作为外保护壳应用的标准规格

1.1 This specification covers the minimum requirements for and methods of application of exterior gypsum panel products that are specifically designed for use as a substrate for exterior cladding. 1.1.1 This specification does not cover gypsum panel products that are specifically designed for interior applications. 1.2 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories. 1.2.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the fire-rated construction. 1.3 Where sound control is required for a gypsum panel product assembly, the details of construction shall be in accordance with the acoustical test report of an assembly that has met the required acoustical value(s). 1.3.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the sound-rated construction. 1.4 Where resistance to racking loads or shear is required for a gypsum panel product assembly, the details of construction shall be in accordance with the racking or shear test report of an assembly that has met the required racking or shear value(s). 1.4.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the racking or shear-tested construction. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The text of this standard references notes which provide explanatory material. These notes shall not be considered as requirements of the standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Application of Exterior Gypsum Panel Products for Use as Sheathing

ASTM C1396/C1396M-13 石膏板标准规格

1.1 This specification covers the gypsum boards described in 1.1.1-1.1.9.Note 1—Specifications C840, C841, C844 and C1280 contain application procedures for gypsum board. 1.1.1 Gypsum wallboard, designed for use on walls, ceilings, or partitions and that affords a surface suitable to receive decoration. 1.1.2 Predecorated gypsum board, designed for use as the finished surfacing for walls, ceilings, or partitions. 1.1.3 Gypsum backing board, coreboard, and shaftliner board, designed for use as a base in multilayer systems or as a gypsum stud or core in semisolid or solid gypsum board partitions, or in shaft wall assemblies.Note 2—The terms backing board, coreboard, and shaftliner board refer to different end uses. The term gypsum backing board, as used in this specification, shall include gypsum coreboard and gypsum shaftliner board unless otherwise stated. 1.1.4 Water-resistant gypsum backing board, designed primarily to be used as a base for the application of ceramic or plastic tile on walls or ceilings. This product is also suitable for decoration. 1.1.5 Exterior gypsum soffit board, designed for use on exterior soffits and carport ceilings that are completely protected from contact with liquid water. 1.1.6 Gypsum sheathing board, designed for use as sheathing on buildings. 1.1.7 Gypsum base for veneer plaster, designed for use as a base for the application of gypsum veneer plaster. 1.1.8 Gypsum lath, designed for use as a base for the application of gypsum plaster. 1.1.9 Gypsum ceiling board, designed for use on interior ceilings with framing spaced not more than 24 in. [610 mm] on center and that affords a surface suita......

Standard Specification for Gypsum Board

SN/T 3341-2012 石膏板中硫化物含量的测定 亚甲基蓝分光光度法

本标准规定了亚甲基蓝分光光度法测定石膏板中硫化物的含量。本标准适用于石膏板中硫化物含量的测定。 测定范围：石膏板中硫化物含量(以硫化氢计算)为0.50 g/g~80.00 g/g。

Determination of sulfide in gypsum plasterboard.Methylene blue spectrophotometric method

SN/T 2297.6-2012 石膏及石膏制品.第6部分：单质硫的测定

SN/T 2297的本部分规定了高温燃烧红外吸收法测定建筑用石膏及石膏制品中单质硫的含量。 本部分适用于建筑用石膏及石膏制品单质硫含量的测定，方法检测低限为2mg/kg.

Gypsum and gypsum products.Part 6:Determination of sulfur

NF P72-204-1-1:2012 建筑工程 - 使用石膏复合板的内部绝缘和墙衬 - 第1-1部分: 技术标准条款合同单

Building works - Internal insulation and wall linings using gypsum composite panels - Part 1-1 : contract bill of technical model clauses

NF P72-203-1-1:2012 建筑工程. 石膏板的铺设工程. 石膏墙板. 第1-1部分: 技术示范条款承包标书

Building works - Gypsum plasterboards works - Gypsum wallboards - Part 1-1 : contract bill of technical model clauses

NF P72-203-1-2:2012 建筑工程. 石膏板的铺设工程. 石膏墙板. 第1-2部分: 材料选择的一般标准

Building works - Gypsum plasterboards works - Gypsum wallboards - Part 1-2 : general criteria for selection of materials

NF P72-204-1-2:2012 建筑工程 - 使用石膏复合板的内部绝缘和墙衬 - 第1-2部分: 材料选择的通用标准

Building works - Internal insulation and wall linings using gypsum composite panels - Part 1-2 : general criteria for selection of materials

KS L 5509-2012 石膏水泥板

이 표준은 석고, 시멘트 등을 결합재로 하고 섬유 재료 등을 보강재로 해서 초조 성형한 판

Gypsum cement boards