T43 载货汽车 标准查询与下载

QC/T 76.4-1993 矿用自卸汽车试验方法 自动换档转速或车速试验

本标准规定了矿用自卸汽车自动换档转速或车速的试验方法。 　　本标准适用于装用液力机械自动变速器的矿用自卸汽车。

Mining dump truck test method automatic shift speed or vehicle speed test

QC/T 76.3-1993 矿用自卸汽车试验方法 爬坡能力试验

本标准规定了矿用自卸汽车爬坡能力试验方法。 　　本标准适用于各种矿用自卸车。

Test method of mining dump truck climbing ability test

QC/T 76.2-1993 矿用自卸汽车试验方法 驾驶员座位基准点R测量方法

本标准规定了矿用自卸汽车驾驶员座位基准点(R点)的测量方法。 　　本标准适用于各种矿用自卸汽车。

Test method of mine dump truck - Measurement method of driver's seat reference point R

QC/T 76.1-1993 矿用自卸汽车试验方法 通则

本标准规定了矿用自卸汽车试验方法中通用的试验条件和试验车辆的准备工作。 　　本标准适用于一柴油机为动力的各种矿用自卸汽车。

General rules of test methods for mining dump trucks

DIN 73400:1993 道路车辆.带卡紧装置的盖.尺寸

The dimensions are given for bajonet clamping used on caps, filler necks and their ramp seats of containers.#,,#

Road vehicles; caps with bajonet clamping; dimensions

JIS D 4010:1993 货车后横梁上机械连接装置的安装

この規格は，自動車総荷量が34.3 kNを超えるフルトレージをけん引するトジックに用いる連結装置のりアクロスメンバへの取付寸法について規定する。

Mounting of mechanical coupling devices on rear cross members of trucks

ISO 9138:1993 磨粒粒度 取样和裂解

Sampling is made using a sampling thief. Splitting means dividing into two equal portions using a splitter (commonly a Jones sampler) and repeating this procedure at each of the portions obtained until the sample is 25 % larger than the amount required for testing. The method may be used in the comparative testing of uniformly produced abrasive grains.

Abrasive grains; sampling and splitting

NAVY MIL-STD-1320-73 A-1993 (RIM-7D,RIM-7E,RIM-7F,RIM-7M,和RIM-7P)在集装箱MK MOD 0和MOD 1卡车装载三型飞弹

THIS CX3CUMENT GWES DETA[ LED lNSTRUCTlONS FOR TRUCKLOADING THE SPARROW 11!MISSILE R!M.7D, RIM.7E, RIM.7F, RIM.7M, AND IW.7P IN mE SHIPPING ANO STORAGE CONTAINERS MK 470 MOD 0 AND MOD I.

TRUCKLOADING SPARROW III MISSILE, (RIM-7D, RIM-7E, RIM-7F, RIM-7M, AND RIM-7P) IN CONTAINER MK 470 MOD 0 AND MOD 1

ARMY MIL-T-62735-1992 商用卡车及拖车的一般规定

This specification covers general requirements for the classes, models and types of modified commercial trucks indicated in the specification title above and in 1.2 below. only as a document to be referenced in detail specification sheets that must, as a minimum, cover detailed truck body requirements and specify the model and class required from table I. This specification is intended 0

TRUCKS AND TRUCK TRACTORS: MODIFIED COMMERCIAL, GENERAL SPECIFICATION FOR

ARMY MIL-T-62316 B-1992 3900千克(8.600 磅) GVW.4X2型.平板厢式货车的维修及校正

This specification covers diesel or gasoline engine driven, four-wheel, two-rear wheel drive, forward control type commercial panel trucks, with cabinetry and shelving. weight(GVW) of 3900 kilograms(kg)(8,600 pounds).

TRUCK, VAN, PANEL: CALIBRATION AND REPAIR: 3900 KILOGRAMS (8,600 POUNDS) GVW, 4X2, MODIFIED COMMERCIAL

NAVY MIL-STD-1320-268-1992 5.0英寸火箭MK22 MOD 4(满装载)在集装箱MK575 MOD 0卡车装载电机

THIS DOCUMENT GIVES DETAILED INSTRUCTIONS FOR TRUCKLOADING UNITIZED LOADS OF THE 5" ROCKET MOTOR MK 22 MOD 4UNITIZED AS SHOWN IN DETAILS C & D ON PAGE 5.

TRUCKLOADING MOTOR, 5.0 INCH ROCKET MK 22 MOD 4 (LOADED ASSEMBLY) IN CONTAINER MK 757 MOD 0

ASME B56.11.3-1992 机动工业货车用货物搬运符号

Load handling symbols for powered industrial trucks

QC/T 29037-1991 微型货车可靠性行驶试验方法

本标准规定了微型货车可靠性行驶试验方法，用以评价微型货车在规定条件下颌规定里程(时间)内完成规定功能的能力。 　　本标准适用于微型货车(含微型厢式货车)，也适用于微型客车及其变型车。

Mini-truck reliability driving test method

QC/T 29022-1991 微型货车耐久性行驶试验方法

Test method for durability driving of miniature trucks

QC/T 29020-1991 微型货车定型试验规程

Miniature truck type test procedure

QC/T 29021-1991 微型货车防尘密封性试验方法

Test method for dust tightness of minivans

HBm 66.58-1991 微型货车 点火开关

本标准规定了微型货车点火开关的基本参数、技术要求、试验方法、检验规则和标志、包装、运输、贮存。 　　本标准适用于微型货车点火开关（以下简称开关）。

minivan ignition switch

HBm 66.56-1991 微型货车 麦弗逊式悬架横臂球销技术条件

本标准规定了微型货车麦弗逊式悬架横臂球销技术要求，试验方法，检验规则和标志、包装、运输、贮存。

Specifications for ball pins of MacPherson suspension for miniature trucks

HBm 66.57-1991 微型货车 制动器疲劳强度台架试验方法

本标准规定了微型货车制动器疲劳强度台架试验的试验条件、试验设备、试验方法、记录内容等。 　　本标准适用于微型货车制动器，其它载货汽车也可参照使用。

Bench test method for fatigue strength of miniature truck brakes

HBm 66.55-1991 微型货车 麦弗逊式悬架横臂技术条件

本标准规定了微型货车麦弗逊式悬架横臂技术要求，试验方法，检验规则和标志，包装、运输、贮存。 　　本标准适用于微型货车麦弗逊式悬架横臂（以下简称横臂）。

Specifications for cross-arm of MacPherson suspension for miniature trucks