U12 船体通用结构 标准查询与下载

KS V ISO 3903:2011 船舶与海洋技术.普通矩形窗

? ??? ??? ??(角窓)? ??(??, ??, ?? ? ?? ??), ??? ? ??

Ships’ ordinary rectangular windows

ISO/PAS 30004:2011 轮船和海洋技术.轮船再循环管理系统.ISO 30000标准实施指南

Ships and marine technology - Ship recycling management systems - Guidelines for the implementation of ISO 30000

CB 20001-2011 登陆舰首门及首总段整体建造工艺要求

本标准规定了登陆舰对开式首门及首总段整体建造过程中的工艺准备、下料加工、单元件组装、首门组合件建造、首门组合件与首总段整体建造。 本标准适用于设置对开式首门的各型登陆舰。

Technical requirements of bow door and bow block complete construction for landing ship

CB/T 4192-2011 潜水器和水下装置耐压结构材料技术条件

本标准规定了潜水器和水下装置耐压结构用钢板、型钢、钢锻件、焊接材料的要求、试验方法、检验规则。 本标准适用于潜水器、水下装置和甲板加压舱的钢质耐压结构的选材。潜水模拟舱的耐压结构亦可参照使用。

Technical specifications of material of pressure hull structure for submersibles and underwater equipments

CB/T 4191-2011 潜水器和水下装置耐压结构制造技术条件

本标准规定了潜水器和水下装置耐压结构的制造要求和液压试验方法。 本标准适用于潜水器、水下装置和甲板加压舱的钢质耐压结构的制造。潜水模拟舱的耐压结构可参照使用。

Technical specifications of manufacture of pressure hull structure for submersibles and underwater equipments

JIS F 0420:2009 船舶和海洋技术.船桥布局及相关设备.要求和指南

Ships and marine technology -- Ship's bridge layout and associated equipment -- Requirements and guidelines

ISO 12215-8:2009 小型船舶.船体结构和船材尺寸.第8部分:船舵

Small craft - Hull construction and scantlings - Part 8: Rudders

ASTM E2664-09a 处理涤纶级乙二醇的海洋船舶清洗甲醇壁的标准试验方法

The methanol wall wash test is performed to determine the cleanliness and suitability of cargo tanks or compartments on a marine vessel prior to loading polyester grade monoethylene glycol. Polyester grade monoethylene glycol has very high quality requirements and must be handled with care, as it is adversely affected by oxygen, hydrocarbons, water and chloride. It is especially susceptible to aromatic contamination, which degrades UV transmittance. Possible sources of contamination are the prior cargoes and cleaning agents. The methanol wall wash procedure provides a representative sampling of the impurities and contamination present on the sides of the cargo tank. The test methods used for analysis of the methanol wall wash samples are capable of determining low levels of impurities or contamination in methanol. These tests include appearance, color, hydrocarbons and chloride. The producers of polyester grade monoethylene glycol need confirmation of the cleanliness and suitability of the marine vessel’s tanks prior to loading with in-specification material. Cargo tanks that do not pass the wall wash test should not be loaded. Alternative test methods and technology for several of the methods can be found in the Appendix. The alternative test methods do not have precision data for the application of these methods in analyzing methanol. Use of these methods is optional and individuals using the alternative methods should assure themselves that the method is sufficiently precise. Precision data is only for the original test methods listed.1.1 This test method covers the methanol wall wash procedure and the chemical and physical analysis of the wall wash sampling for cargo tanks of marine vessels handling polyester grade monoethylene glycol. The key sections for the wall wash procedure and test methods appear in the following order: Sections Wall Wash Procedure7 and 8 Appearance9-11 Color12-14 Hydrocarbons15-17 Chloride18-21 1.2 The values given in SI units are to be considered as the standard. No other units of measurement are included in this standard. 1.3 Review the current Material Safety Data Sheet (MSDS) for detailed information concerning toxicity, first aid procedures and safety precautions. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 6.

Standard Test Method for Methanol Wall Wash of Marine Vessels Handling Polyester Grade Monoethylene Glycol

KS V ISO TR 14564:2008 造船和海上建筑物.安全疏散标记

Shipbuilding and marine structures-Marking of escape routes

CB/T 3277-2008 船体结构.钢质护舷材

本标准规定了船体结构钢质护舷材的型式、主要尺寸及要求。 本标准适用于沿海的拖船、客货船、工程船及驳船的钢质护舷材的设计和选用，其他船舶的钢质护舷材的设计和选用可参照使用。

Hull structure.Steel fender

CB/T 3184-2008 船体结构流水孔、透气孔、通焊孔和密性焊段孔

本标准规定了船体结构流水孔、透气孔、通焊孔和密性焊段孔的型式、尺寸和设计要求。 本标准适用于钢质船体结构流水孔、透气孔、通焊孔和密性焊段孔的设计和选用。

Hull structure-Drain hole,air hole,clearance hole and scallop for seal welding

ASTM F1385-07 载油舱平台的标准实施规程

This practice establishes the procedure for the construction and installation of platforms to be fabricated and installed by the shipyards within the cargo tanks. 1.1 This practice provides design, construction, and installation criteria for platforms in cargo tanks. 1.2 Where platforms are attached to ladders see Figs. 1-4. 1.3 The values stated in SI (metric) units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Platforms in Cargo Tanks

DIN 83220-1:2006 船上发动机房和锅炉房的地面.第1部分:工作地面

This standard contain fundamental specifications of the calculation and construction of working floors in engine rooms and boiler rooms on ships. This standard should allow the uniformity of design and the using of similarly components. The number of specific components and the fitting metrics depend on the current local data.

Floors in ship's engine rooms and boiler rooms - Part 1: Working floors

DIN 83221:2006 船上机房和锅炉房的通道

This standard contain fundamental specifications of the calculation and construction of walkways in engine rooms and boiler rooms on ships. Its contain specifications of the support and the substructure of walkways. This standard should allow the uniformity of design and the using of similarly components. The numer of specific components and the fitting metrics depend on the current local data.

Walkways in ship's engine rooms and boiler rooms

DIN 83220-2:2006 船上发动机房和锅炉房的地面.第2部分:中间底部

This standard contain fundamental specifications of the calculation and construction of intermediate floors in engine rooms and boiler rooms on ships. This standard should allow the uniformity of design and the using of similarly components. The number of specific components and the fitting metrics depend on the current local data.

Floors in ship's engine rooms and boiler rooms - Part 2: Intermediate bottoms

DIN 83222:2006 工作面地板、中间底部和通道用带铰链的盖板

This standard is for flaps in working floors depend on DIN 83220-1 and DIN 83220-2 and in walkingways depend on DIN 83221 in engine rooms and boiler rooms on ships.

Hinged flap for working floors, intermediate bottoms and walkways

DIN 83223:2006 工作面地板、凿孔栅栏和通道用球头扁钢和地面格子板

This standard contain fundamental specifications of the calculation and construction of plates out of hot-rolled steel panels with pattern as bulb plates or flooring grids for floors in engine rooms and boiler rooms on ships. By the specifications in this standard the nummer of, in the shipbuilding industry used, bulb plates and flooring girds and whose dimensions are limited.

Bulb plates, perforated gratings or flooring grids for working floors and walkways

ANSI/ASTM F1385:2006 载油舱平台的实施规程

This practice provides design, construction, and installation criteria for platforms in cargo tanks. Where platforms are attached to ladders see Figs. 1-4. The values stated in SI (metric) units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Practice for Platforms in Cargo Tanks

CB/T 3185-2005 船体结构舷墙

本标准规定了船体结构舷墙的普通结构型式及相关尺寸。 本标准适用于露天干舷甲板以及在上层建筑和甲板室甲板上设置的舷墙的设计与建造。

Hull structure--Bulwark

CB/T 3370-2005 箱形船船体结构节点

本标准规定了箱形船船体结构节点的型式和参数。 本标准适用于船长小于65m的起重船、打桩船、挖泥船等非自航的箱形船的设计、其他箱形船舶的设计可参照使用。

Detail of hull structure for box barge