V29 航天用液压元件与附件 标准查询与下载

2M 59-1993 航空航天液压系统用的24°圆锥状米制连接件连接规范

Specification for interface of metric couplings, 24 cone, for aerospace fluid systems

2M 63-1993 航空航天液压系统用端口连接、密封和配件终端尺寸规范

Specification for dimensions of aerospace fluid system port connection, seal and fitting end

NAVY MIL-C-24782-1993 高压汽瓶内部使用粉状含氟聚合物 涂层

This specification covers a powdered fluoropolymer coating of high pressure air flask interiors. By this specification.

COATING, POWDERED FLUOROPOLYMER FOR USE ON HIGH PRESSURE GAS FLASK INTERIORS

JIS W 2921:1993 航空航天.液压系统和部件.压力和温度分类

この規格は，航空宇宙用流体系統に共通に使用する温度の群及び圧力の段階について規定する。

Aerospace -- Fluid systems and components -- Pressure and temperature classifications

SAE AIR1082B-1992 液体.系统.部件规范编制标准

The importance of adequate component procurement specifications to the success of a hardware development program cannot be overemphasized. Specifications which are too stringent can be as detrimental as specifications which are too lax. Performance specifications, for instance, must not only identify all the component requirements, but they must also include sufficient quality assurance provisions so that compliance can be verified. It should be understood that in almost every case specifications for components will ultimately become part of a BINDING, WRITTEN CONTRACT (PO). The purpose of this document is to describe specifications, provide guidance for the preparation of fluid component specifications, and identify documents commonly referenced in fluid component specifications.

Fluid-System-Component Specification Preparation Criteria

SAE AIR1388B-1992 飞机液压管的检修损害极限

This SAE Aerospace Information Report (AIR) is intended to assist in evaluating the serviceability of damaged hydraulic tubing lines. The performance requirements are outlined to which the defect sample were tested. Test methods and data are described and summarized. Permissible defect limits are listed for 6061-T6 aluminum return lines, 3000 psi hydraulic tubing of 21Cr-6Ni-9Mn SS, 304 1/8 hard, corrosion resistant steel (CRES), as well as 3Al-2.5V CWRS and 3Al-2.5V annealed, seamless titanium tubing. All dimensions are in inches unless otherwise noted.

Service Damage Limits for Aircraft Hydraulic Tubing

SAE AS4265-1992 液压管和配件的脉冲试验,S-N弯曲

This aerospace test standard establishes the requirements and procedures for evaluating and comparing the impulse fatigue performance of high pressure hydraulic fittings and tubing. this test method may be used to test similar fluid system components, if desired.

Impulse Testing of Hydraulic Tubing and Fittings, S-N Curve

DIN 65385:1991 航空航天.液压流体动力..过滤器元件.试验数据报告

The standard covers the reporting methods related to already existing test standards which summarize all data required to evaluate the result within the meaning of the test standard applied.

Aerospace; hydraulic fluid power; filter elements; reporting of test data

NAVY MIL-S-21427 B (1)-1991 高压(尺寸4英寸及以上)主蒸汽集中滤网

This amendment forms a part of MIL-S-21427B(SH), dated 6 March 1989, and is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense.

STRAINER, ASSEMBLIES, MAIN STEAM, HIGH PRESSURE (SIZES 4 INCHES AND ABOVE)

NAVY MIL-V-24658 VALID NOTICE 1-1991 高压天然气还原的静设计阀组

MIL-V-24658(SH) dated 30 August 1985, has been reviewed and determined to be valid for use in acquisition,

VALVE MANIFOLDS, QUIET DESIGN, HIGH PRESSURE GAS REDUCING

NF L45-201*NF ISO 9206:1991 航空和航天.恒排量液压马达.通用规范

Aerospace. Constant displacement hydraulic motors. General specifications.

SAE AS1896A-1991 一侧自密封液压连接器总成

This document establishes the requirements for aircraft, hydraulic couplings, self sealing one side only, for use in Type II hydraulic systems (-65?to +275 °F temperature range) as defined by MIL-H-5440. The purpose being to connect a hose or tube to a standard MS33656, MS33514 or MIL-F-85421 fitting and provide the self sealing feature on the hose or tube side of the connection.

Coupling Assembly, Self-Sealing, One Side Only, Hydraulic

ISO 8574:1990 航空航天 液压系统管路安装 合格试验

Aerospace; hydraulic system tubing; qualification tests

NF L41-114:1990 航空流体电路中的污染.过滤器和过滤元件.过滤介质的移动

Contamination in aircraft fluid circuits - Filter and filter elements - Migration of the filter medium

Contamination in aircraft fluid circuits - Filter and filter elements - Migration of the filter medium

QJ 1901-1990 电液伺服机构通用技术条件

General technical specification for electro-hydraulic servomechanism

QJ 1895-1990 地面设备液压系统安装、使用、维修技术条件

Technical conditions for installation, use and maintenance of ground equipment hydraulic system

DIN ISO 5884:1989 航空航天.流体系统和部件.液压流体中固体微粒污染的系统取样和测量方法

This standard specifies the methods for system sampling and measuring of the solid particle contamination of hydraulic fluids.

Aerospace; fluid systems and components; methods for system sampling and measuring the solid particle contamination of hydraulic fluids; identical with ISO 5884:1987

HB 6365-1989 电动机驱动的变量液压泵通用技术条件

本标准规定了飞机液压系统由电动机驱动的液压变量泵（以下简称变量泵）的一般要求及试验方法。 　　本标准适用于新产品的研制及其批生产。

General specification for variable displacement hydraulic pump driven by electric motor

NF L41-118:1989 航空流体电路的污染.过滤器滤波元件.清洁状况测定方法

Contamination in aircraft fluid cicuits - Filters filter elements - Method for determining the state of cleanliness

Contamination in aircraft fluid cicuits - Filters filter elements - Method for determining the state of cleanliness

NAVY MIL-S-21427 B-1989 高压(尺寸4英寸及以上)主蒸汽集中滤网

This specification is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense.

STRAINER, ASSEMBLIES, MAIN STEAM, HIGH PRESSURE (SIZES 4 INCHES AND ABOVE)