V29 航天用液压元件与附件 标准查询与下载

NAVY MIL-PRF-32195-2005 大容量高压呼吸压缩空气机(HPBAC)

This specification covers the High Pressure Breathing Air Compressor (HPBAC) used by Navy personnel as part of the shipboard breathing air system to refill breathing air cylinders used with the open-circuit self contained breathing apparatus (SCBA). This equipment will be used on Navy ships and at Navy Training Centers for rapid charge of breathing air cylinders.

LARGE CAPACITY HIGH PRESSURE BREATHING AIR COMPRESSOR (HPBAC)

SAE AS24334B-2005 内螺纹轴衬用非扩口配件自密封液压连接组件

Coupling Assembly, Hydraulic, Self-Sealing, Flareless Fitting to Internal Thread Boss FSC 4730; Should Be Used Instead of MS24334FIGURE 1 - COUPLING ASSEMBLY, FLARELESS, HYDRAULICTABLE 1A - DIMENSIONS A-ETABLE 1B - DIMENSIONS F-K

Coupling Assembly, Hydraulic, Self-Sealing, Flareless Fitting to Internal Thread Boss FSC 4730; Should Be Used Instead of MS24334

ISO 8574:2004 航空航天.液压系统管路安装.弯管的合格试验

This International Standard specifies pressure impulse and burst test procedures for determining and classifying the impulse fatigue strengths of bent tubes used in aerospace hydraulic systems. The procedures are intended for qualification purposes of high- and low-pressure system tubing or for the evaluation of new materials for hydraulic system tubing. NOTE Requirements for tubing used in aerospace hydraulic systems are given in ISO 8575.

Aerospace - Hydraulic system tubing - Qualification tests for bent tubes

NAVY QPL-24574-10-2004 低压和高压氧化气体混合物使用的润滑液

This list has been prepared for use by or for the Government in the acquisition of products covered by the subject specification and such listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense. All products listed herein have been qualified under the requirements for the product as specified in the latest effective issue of the applicable specification. This list is subject to change without notice; revision or amendment of this list will be issued as necessary. The listing of a product does not release the contractor from compliance with the specification requirements.

LUBRICATING FLUID FOR LOW AND HIGH PRESSURE OXIDIZING GAS MIXTURES

SAE ARP988-2003 电动液压机械反馈伺服执行机构

This recommended practice is intended as a guide for the specification of electrohydraulic mechanical feedback servoactuators used for position control. The recommendations contained herein are confined to the input and output characteristics of electrohydraulic mechanical feedback servoactuators. The information presented should be useful for standardizing the terminology and for specification of physical and performance parameters. The recommendations do not restrict nor attempt to define the internal design characteristics of servoactuators. As such, the material is equally applicable to servoactuators having different internal functioning, different ratings, different physical size, etc. In certain instances, standards for actuator design are recommended to increase interchangeability as, for example, pigtail color-coding and actuator polarity. The specifications contained herein should be adequate to describe electrohydraulic mechanical feedback servoactuators used for position control systems. Certain dynamic compensation methods will be discussed.

Electrohydraulic Mechanical Feedback Servoactuators

SAE AS5164A-2003 45 多种流体压力线连接器接头

Fitting, Connector, Multiple Fluid Pressure Line, 45TABLE 1A - DIMENSIONSTABLE 1B - DIMENSIONS AND WEIGHTS

Fitting, Connector, Multiple Fluid Pressure Line, 45

BS ISO 7314:2003 航空航天.液压系统.金属软管组件

This International Standard gives specifications for medium pressure, high temperature, flexible metal hose assemblies suitable for continuous operation in liquid and pneumatic systems from - 55 ℃ to + 400 ℃, with short duration excursions up to + 650 ℃. The hose assemblies covered by this International Standard are intended for use in aerospace applications for conveying air and other gases in pneumatic systems, bleed air systems, heating and ventilating systems and instrument air systems when used at pressures and temperatures within the limits laid down in Tables 2 and 3. This International Standard does not cover flow velocity in such assemblies exceeding 54 m/s; higher velocities require special vibration-dampening devices. Hose assemblies supplied to the specifications laid down in this International Standard may be of two types: — Type 1: Convoluted inner tube - welded, of moderate mass and moderate flexibility. — Type 2: Convoluted inner tube - seamless or butt-welded and redrawn, of low mass and high flexibility.

Aerospace. Fluid systems. Metal hose assemblies

SAE AS5902-2002 对外陷型配件的安装

This document describes engineering requirements for installation of externally swaged fittings used in aerospace fluid systems.

Installation of Externally Swaged Fittings

SAE AS85352-2002 FSC 4920直读式可远程控制的增压泵组件和计量器元件

This specification covers a direct reading, remote control, pneumatic pressure inflator assembly, for use on aircraft tires and struts having pneumatic pressure requirements up to 600 psi. It includes pressure relief provisions to provide for safe inflation. Also included are dual chuck stem gages for measuring tire pressure. Classification: Inflator assemblies and gage elements shall be as specified.

Inflator Assembly and Gage Elements, Pneumatic Pressure, Remote Control, Direct Reading FSC 4920

AECMA PREN 3545-007-2002 航空航天系列. 尾部密封和无密封塑料护套、锁紧装置、工作温度操作温度-55°C至175°C的矩形电接点.第007部分;电缆钳.产品标准

This draft is now available for public comment and your views and technical comments on it would be appreciated. If you have no specific comments to make hut find it generally acceptable it would be helpful if you would notify US accordingly. Suggestions entailing revision of the text should indicate the preferred wording. Please quote the relevant clause number against any comment.

Aerospace Series Connectors, Electrical, Rectangular, with Sealed and Non-Sealed Rear, Plastic Housing, Locking Device, Operating Temperatures - 55 Degrees C to 175 Degrees C Part 007 : Cable Clamp Product Standard Edition P 2

SAE ARP901A-2001 起泡点测试方法

This test method describes a procedure for measuring the largest pore or hole in a filter or similar fluid-permeable porous structure. A standard referee test method for precise determination or resolution of disputes is specified. A simpler inspection test procedure for quality assurance go-no-go measurement is also given. Bubble-point testing physics, analysis of bubble-point test data, and correlation with other methods of pore size determination are separately discussed in the appendix.

Bubble-Point Test Method

SAE AS4059D-2001 航空航天液力传动.液压液的清洁度分类

This SAE Aerospace Standard (AS) defines cleanliness levels for particulate contamination of hydraulic fluids and includes methods of reporting data relating to the contamination levels. The contamination levels selected are an extension and simplification of the widely accepted NAS 1638 cleanliness levels. The intent of this document is to establish the minimum information required to allow valid comparison and interpretation of contamination levels in hydraulic systems that require contamination control of particulate to insure system performance and reliability.

Aerospace Fluid Power - Cleanliness Classification for Hydraulic Fluids

SAE AIR1899A-2001 航空航天军用飞机液压系统特征

This SAE Aerospace Information Report (AIR) has been compiled to provide information on hydraulic systems fitted to the following categories of military vehicles: attack airplanes, fighter airplanes; bombers; anti-sub, fixed wing airplanes; transport airplanes; helicopters; and boats. The purpose of this document is to provide hydraulic system information to military vehicle system and component designers in order to assist them in future aircraft fluid power system designs.

Aerospace Military Aircraft Hydraulic System Characteristics

SAE ARP1201C-2001 (R)液压配件用六角形棒材,机制扁材和锻造扳紧扁材的尺寸公差

This SAE Aerospace Recommended Practice (ARP) lists wrenching surface sizes and tolerances for fluid fittings which utilize machined or unmachined hex bar dimensions and machined or forged wrenching surfaces across the center body section of shape fittings.

(R) Tolerances, Hexagon Bar, Machined Flat and Forged Wrenching Flat Sizes for Fluid Fittings

SAE AS683C-2001 液体连接的安装程序和力矩

To establish standard installation procedures for fluid connection parts listed in this standard.

Installation Procedures and Torques for Fluid Connections

EN 3788:2001 航空航天系列.管道连接8°30′.保护盖

This standard specifies characteristics for protective caps for pipe couplings 8°30″,used to protect metric pipe ends during transportation and storage,for aerospace applications. The caps shall be pushed on/off the tube ends.

Aerospace Series - Pipe Coupling 8 Degrees 30?- Protective Caps

JIS W 2923:2000 航空航天.流体系统和部件.液压流体的固体颗粒污染物的系统取样和测量方法

この規格では，航空宇宙用の油圧系統及び機器に用いる作動油の，固体微粒子汚染のレべルを決定するための測定方法として，次の3方法について規定する。

Aerospace -- Fluid systems and components -- Methods for system sampling and measuring the solid particle contamination of hydraulic fluids

JIS W 0125-3:2000 航空航天.流体系统.词汇.第3部分:与温度有关的术语和定义

この規格は，航空宇宙用構造物に使用する流体系統の温度に関する一般用語の定義を規定する。

Aerospace -- Fluid systems -- Vocabulary -- Part 3: General terms and definitions relating to temperature

JIS W 0125-2:2000 航空航天.流体系统.词汇.第2部分:与流动有关的术语和定义

この規格は，航空宇宙用構造物に使用する流体系統の流れに関する一般用語の定義を規定する。

Aerospace -- Fluid systems -- Vocabulary -- Part 2: General terms and definitions relating to flow

JIS W 0125-1:2000 航空航天.流体系统.词汇.第1部分:与压力有关的一般术语和定义

この規格は，航空宇宙用構造物に使用する流体系統の圧力に関する一般用語の定義を規定する。

Aerospace -- Fluid systems -- Vocabulary -- Part 1: General terms and definitions relating to pressure