V29 航天用液压元件与附件 标准查询与下载

SAE AS1300A-1988 环锁液压连接型,孔的标准尺寸

Port - Ring Locked Fluid Connection Type, Standard Dimensions for (Reaffirmed: 01 Apr 1993) (Reaffirmed: 01 Oct 2000)

QJ 1445-1988 液压导管接头和连接件回转弯曲试验方法

Rotary bend test method for hydraulic conduit fittings and fittings

QJ 1444-1988 航天液压系统软管、导管和接头组件脉冲试验

Impulse Testing of Aerospace Hydraulic System Hoses, Conduits, and Fitting Assemblies

QJ 1443-1988 航天液压系统导管和接头组件热冲击试验

Thermal Shock Test of Aerospace Hydraulic System Conduit and Fitting Components

HB 6146-1988 航空高精度液压过滤器通用技术条件

本标准规定了对额定工作压力为21MPa，绝对过滤度分别为1、2、3、4、5μm液压过滤器的一般技术要求。 　　本标准适用于航空高精度液压过滤器及滤芯的新品研制及其批生产和老产品改进、改型。

General Technical Specifications for Aviation High Precision Hydraulic Filters

NAVY DOD-PRF-24574 (2)-1987 低高压氧化气体混合物润滑液体

This amendment forms a part of DOD-L-24574(SH), dated 29 September 1978,and is approved for use within the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense.

LUBRICATING FLUID FOR LOW AND HIGH PRESSURE OXIDIZING GAS MIXTURES

BS M 62:1987 具有轴向对准的流体系统管道的夹具块的设计和鉴定测试规范 公制系列

With or without electrical grounding, designed for a range of outside diameters 4 to 32 mm, selected from 2M 46.

Specification for design and qualification testing of clamp blocks for fluid system tube lines having axial alignment. Metric series

QJ 1098-1986 地面设备液压缸通用技术条件

General Specifications for Ground Equipment Hydraulic Cylinders

QJ 498-1986 液压缸筒硬铬镀层技术条件

Specifications for hard chrome plating of hydraulic cylinders

NF L41-123:1986 飞行器液压回路污染.过滤器.绝对过滤比测量

Contamination in aircraft hydraulic circuits - Filters - Absolute filtration rating measurement

Contamination in aircraft hydraulic circuits - Filters - Absolute filtration rating measurement

NF L41-121:1986 航行器液压回路的污染.过滤器.压降流量特性的测定

Contamination in aircraft hydraulic circuits - Filters - Determination of hydraulic pressure drop versus flow characteristics

Contamination in aircraft hydraulic circuits - Filters - Determination of hydraulic pressure drop versus flow characteristics

NF L41-120:1986 航空流体电路的污染.过滤器.定义和特性

Contamination in aircraft hydraulic circuits - Filters - Definitions and characteristics

Contamination in aircraft hydraulic circuits - Filters - Definitions and characteristics

NF L41-122:1986 航行器液压回路的污染.过滤器.冷启动

Contamination in aircraft hydraulic circuits - Filters - Cold start

Contamination in aircraft hydraulic circuits - Filters - Cold start

HB 5942-1986 飞机压力加油接头尺寸标准

Dimensional standards for aircraft pressure refueling fittings

SAE ARP1974-1986 支架夹对比疲劳强度的试验方法

This recommended practice establishes vibration and transmissibility test procedures which compare the relative strengths of various loop and saddle type support clamps. This procedure is intended for conducting fatigue testing which is standard throughout the aerospace industry thereby establishing a clamp strength comparison which can be used in an evaluation process. The testing required by this recommended practice ensures that clamps will meet adequate fatigue requirements only. It does not infer qualification of the clamp installation techniques or its ability to meet in-service environments or operating conditions. Separate qualification testing should be performed to ensure satisfactory service of the installed clamp.

Clamps, Support, Comparative Fatigue Strengths, Test Method

QJ 976-1986 液压系统及元件压力温度分级

Pressure and temperature classification of hydraulic system and components

HB 5891-1985 飞机液压安全阀通用技术条件

本技术条件规定了飞机液压系统液压安全阀的一般技术要求。 　　适用于飞机液压安全阀（以下简称产品）的研制及其批生产。

General specifications for aircraft hydraulic safety valves

NAVY MIL-V-24658-1985 高压天然气还原的静设计阀组

This specification covers the design, construction, test, and operating requirements for quiet design, high pressure air or nitrogen reducing valve manifolds.

VALVE MANIFOLDS, QUIET DESIGN, HIGH PRESSURE GAS REDUCING

NAVY MIL-V-24272 B-1985 高压天然气减少阀组

This specification covers the design, construction, test and operating requirements for high pressure air or nitrogen reducing valve manifolds.

VALVE MANIFOLDS, HIGH PRESSURE GAS REDUCING

SAE AIR1590-1984(R2007) 英制测量流体系统部件用推荐零件编号指南

This standard considers the part numbering system for hose assemblies,fittings,and clamps.Other component types could be added later.Each component type has established standard codes which are unique that type and cannot be interchanged with other component types.The recommendations based on the metric system of measurement see(TBD).

Recommended part numbering guidelines for fluid system components inch system of measurements