13.220.99 有关消防的其他标准 标准查询与下载

BS EN 15882-5:2021 服务设施耐火测试结果的扩展应用 组合渗透密封

What is BS EN 15882-5-about?     BS EN 15882-5 is the fifth part of a multi-series that specifies the principles and guidance for the preparation of extended application documents for combined penetration seals, where the systems were tested in accordance with (EN 1366 ‑ 3 and EN 1366 ‑ 1) or (EN 1366 ‑ 3 and EN 1366 ‑ 2). This EXAP is intended to allow the penetration sealing of more than one service    (e.g., cables, pipes, conduits) and four-sided fire resisting ducts (ventilation ducts) or fire dampers in the same penetration.   The field of the EXAP document is added to the direct field of application given within EN 1366 ‑ 1, EN 1366 ‑ 2, and EN 1366 ‑ 3 and can be applied on several tests from each standard, which provide the relevant information for the formulation of an extended application. 

Extended application of results from fire resistance tests for service installations - Combined penetration seals

DB37/T 4426-2021 城市消防安全评价导则

Urban Fire Safety Evaluation Guidelines

DS/EN 15882-5:2021 服务设施耐火试验结果的扩展应用 第5部分：组合渗透密封

Extended application of results from fire resistance tests for service installations – Part 5: Combined penetration seals

EN 15882-5:2021 服务设施耐火试验结果的扩展应用 第5部分：组合渗透密封

Extended application of results from fire resistance tests for service installations - Part 5: Combined penetration seals

DS/EN IEC 60695-6-1:2021 火灾隐患测试 第 6-1 部分：烟雾遮挡 一般指南

Fire hazard testing – Part 6-1: Smoke obscuration – General guidance

BS EN IEC 60695-6-1:2021 火灾隐患试验. 第6-1部分: 烟雾灰暗度. 一般导则

Fire hazard testing. Smoke obscuration. General guidance

EN IEC 60695-6-1:2021 火灾隐患测试 第 6-1 部分：烟雾遮挡 一般指南

IEC 60695-6-1:2021 is available as IEC 60695-6-1:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60695-6-1:2021 gives guidance on: a) the optical measurement of obscuration of smoke; b) general aspects of optical smoke test methods; c) consideration of test methods; d) expression of smoke test data; e) the relevance of optical smoke data to hazard assessment. This basic safety publication focusing on safety guidance is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. This third edition cancels and replaces the second edition of IEC 60695-6-1 published in 2005 and Amendment 1:2010. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - References to IEC TS 60695-6-30 (withdrawn in 2016) have been removed. - References to IEC TS 60695-6-31 (withdrawn in 2016) have been removed. - References to ISO 5659-2 have been inserted. - The scope contains some additional text. - Terms and definitions have been updated. - Subclause 3.2 has been updated. - Subclause 7.1 has been updated. It has the status of a basic safety publication in accordance with IEC Guide 104 and ISO/IEC Guide 51. This International Standard is to be used in conjunction with IEC 60695-6-2.

Fire hazard testing - Part 6-1: Smoke obscuration - General guidance

DB23/T 2937-2021 黑龙江省多功能火灾疏散指示信息系统技术规程

Heilongjiang Province Multifunctional Fire Evacuation Instruction Information System Technical Regulations

DB50/T 1114-2021 区域消防安全风险评估规程

本文件适用于以重庆市行政区划和经济开发区域为单位的城市、县城、乡镇（街道）的建成区、规划区消防安全评估。其它根据实际需求划定区域的消防安全评估，可参照本标准执行

Regional Fire Safety Risk Assessment Procedures

DS/IEC TS 60695-5-2:2021 火灾隐患试验《第5-2部分：火灾排放物的腐蚀破坏效应》试验方法的总结和相关性

Fire hazard testing – Part 5-2: Corrosion damage effects of fire effluent – Summary and relevance of test methods

IEC TS 60695-5-2:2021 RLV 火灾危险试验第5-2部分:火灾流出物的腐蚀损伤效应试验方法的总结和相关性

Fire hazard testing - Part 5-2: Corrosion damage effects of fire effluent - Summary and relevance of test methods

IEC TS 60695-5-2:2021 火灾危险测试 第 5-2 部分：火灾排放物的腐蚀损害影响 测试方法的总结和相关性

Fire hazard testing - Part 5-2: Corrosion damage effects of fire effluent - Summary and relevance of test methods

OENORM EN 15882-2-2021 服务设施耐火试验结果的扩展应用 第2部分：防火阀

Extended application of results from fire resistance tests for service installations - Part 2: Fire dampers

ASTM F3386/F3386M-21 爆震阻火器的默认规范

1.1 This specification provides the minimum requirements for design, construction, performance, and testing of detonation flame arresters intended to protect against deflagrations, overdriven (unstable) detonations, stable detonations, and stabilized burning. 1.2 This specification is intended for detonation flame arresters installed in vapor control systems at Marine Facilities subject to the requirements in 33 CFR, Part 154, Subpart P — Marine Vapor Control Systems. NOTE 1—In 1990, by permission from ASTM International, an earlier draft of this specification was incorporated and printed in 33 CFR, Part 154, Appendix A. 1.3 This specification is intended for detonation flame arresters protecting systems containing gases or vapors of liquids with flash points 140°F [60°C] (closed cup) or less. The tests in this specification are intended to qualify detonation flame arresters for all in-line applications, provided the operating pressure is equal to or less than the maximum operating pressure stated in the manufacturer’s certification, and the diameter of the piping system in which the detonation flame arrester is to be installed is equal to or less than the piping diameter used in the testing. 1.4 This specification is limited to detonation flame arresters operating at temperatures no greater than 140°F [60°C], unless the detonation flame arresters are tested at the higher operating temperatures. NOTE 2—Refer to UL 525 for additional requirements that may be applicable. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Detonation Flame Arresters

prEN 15882-2-2021 服务设施耐火试验结果的扩展应用 第2部分：防火阀

Extended application of results from fire resistance tests for service installations - Part 2: Fire dampers

DIN/TS 18232-8:2021 烟雾和热控制系统 用于通风和排烟目的的建筑覆盖物的开口装置 要求和测试方法

This document gives requirements and test methods for opening units for building coverings which are situated in roofs or walls and which are used for ventilation and smoke elimination purposes.

Smoke and heat control systems - Opening units for building coverings for ventilation and smoke elimination purposes - Requirements and test methods

DS/ISO/TR 16312-2:2021 用于评估火灾危害和风险评估的火灾排放物毒性数据的物理火灾模型有效性评估指南第2部分：单个物理火灾模型的评估

Guidance for assessing the validity of physical fire models for obtaining fire effluent toxicity data for fire hazard and risk assessment – Part 2: Evaluation of individual physical fire models

DB3304/T 058-2020 新农村集聚点消防设施配置规范

Specifications for the configuration of fire-fighting facilities in new rural agglomeration points

DB45/T 2251-2021 城市轨道交通消防警情与救援监控系统技术规范

Technical Specifications for Urban Rail Transit Fire Alarm and Rescue Monitoring System

BS PD ISO/TR 16312-2:2021 用于评估物理火灾模型有效性的指南，用于获得火灾危害和风险评估的火灾流出物毒性数据 单个物理火灾模型的评估

Guidance for assessing the validity of physical fire models for obtaining fire effluent toxicity data for fire hazard and risk assessment. Evaluation of individual physical fire models