19.080 电工和电子试验 标准查询与下载
共找到 481 条与 电工和电子试验 相关的标准，共 33 页
本文件规定了自主安全台式机的测试策略、测试内容、测试方法、测试中止条件、测试结果评判等。 内容，是开展自主安全台式机测试的指导性依据文件。 本文件适用于第三方测试机构开展产品质量测试。
Information Technology Application Innovation General Test Specifications for Autonomous Security Equipment Part 1: Desktop Computers
- ICS
- 19.080
- CCS
- M745
- 发布
- 2024-03-14
- 实施
- 2024-04-15
IEC 61010-031:2022 specifies safety requirements for hand-held and hand-manipulated probe assemblies for electrical test and measurement, and their related accessories. These probe assemblies are for non-contact or direct electrical connection between a part and electrical test and measurement equipment. They can be fixed to the equipment or be detachable accessories for the equipment. It has the status of a group safety publication in accordance with IEC Guide 104. This third edition cancels and replaces the second edition published in 2015, and Amendment 1:2018. IEC 61010-031 is a stand-alone standard. This edition includes the following significant technical changes with respect to the previous edition: the scope has been made succinct. General information from the scope of Edition 2 has been moved to a new Clause 4. Consequently, Clause 4 to Clause 8 of Edition 2 have been renumbered. Clause 9 of Edition 2 has been deleted; in Clause 2, normative references have been dated and new normative references have been added; in 3.1.4, the definition of probe tip has been modified; in 4.1, there is no longer any differentiation between high voltage and low voltage probe assemblies. Type C probe assemblies have been merged with Type B probe assemblies; in 4.1 d) "Kelvin" probes have been added to the list of probe assemblies as a new Type E and a new Figure 5; in 4.1 e), probes for voltage measurement without electrical connection to conductors have been added to the list of probe assemblies as a new Type F and a new Figure 6; in 4.2.1, spread of fire is no longer considered as a hazard; Subclause 4.4.2.5 from Edition 2 has been deleted; Subclause 4.4.4.3 from Edition 2 has been deleted; in 5.4.4.1 consideration has been given to spacings and impedance; in 6.1.1, removable parts of probe tips which bear markings are allowed; in 6.1.5, the voltage to be marked for measurement categories is the AC line-to-neutral or DC voltage; in 7.4.2, requirements for unmated connectors have been modified as follows: Table 2 has been modified and expanded, a calculation method for clearances of connectors above 20 kV has been defined, creepage distances have been aligned with clearances; in 7.4.3.1 and 7.4.3.5, requirements for IP2X probe tips with retractable sleeve have been added; in 7.4.3.2, Probe tips are now applicable to non-contact probe assemblies; in 7.5.2.3.2, the values of Table 5 have been modified; in 7.6.2, voltage tests of clearances are done without humidity preconditioning; pre-treatments for rigidity test from Clause 10 of Edition 2 have been moved to 9.2; Subclause 11.1 of Edition 2 has been deleted; addition of an exception for Type E probe assembly in 13.2. Removable parts of probe tips which bear markings are allowed; Figure F.1 has been modified; Annex G has been added, for determination of clearances for Table 2; Annex H has been added, covering line-to-neutral voltages for common mains supply systems.
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 031: Safety requirements for hand-held and hand-manipulated probe assemblies for electrical test and measurement
- ICS
- 19.080
- CCS
- 发布
- 2024-01-31
- 实施
本文件规定了人工模拟高海拔工况的环境条件、电气性能试验、人工模拟高海拔验证试验等。 本文件适用于海拔高于1000 m，不高于5000 m地区使用的电气设备等。
Electrical equipment performance test under the working condition of artificial simulated high altitude
- ICS
- 19.080
- CCS
- C389
- 发布
- 2023-09-27
- 实施
- 2023-09-27
IEC 60112:2020 specifies the method of test for the determination of the proof and comparative tracking indices of solid insulating materials on pieces taken from parts of equipment and on plaques of material using alternating voltage. This document provides a procedure for the determination of erosion when required. This test method evaluates the composition of the material as well as the surface of the material being evaluated. Both the composition and surface condition directly influence the results of the evaluation and are considered when using the results in material selection process. Test results are not directly suitable for the evaluation of safe creepage distances when designing electrical apparatus. This basic safety publication focusing on a safety test method is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and lSO/lEC Guide 51. This edition includes the following significant technical changes with respect to the previous edition: Introduction of a new contaminant, solution C with a surfactant aligned with the test method of IEC 60587. The definition of the solution B was transferred to Annex B for backward reference. Introduction of a screening test, considering the fact that some materials can withstand high test voltages, but fail at lower test voltages. It has the status of a basic safety publication in accordance with IEC Guide 104.
Method for the determination of the proof and the comparative tracking indices of solid insulating materials
- ICS
- 19.080
- CCS
- 发布
- 2023-09-10
- 实施
BS EN IEC 61010-2-011. Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-011. Particular requirements for refrigerating equipment
- ICS
- 19.080
- CCS
- 发布
- 2023-07-26
- 实施
- 2023-07-26
本文件规定了动力电池检测系统的术语和定义、型式与组成、要求、检验方法、检验规则、包装、随机文件、运输、储存。
Technical specification for testing system for high-voltage power batteries
- ICS
- 19.080
- CCS
- C384
- 发布
- 2023-07-25
- 实施
- 2023-07-26
本文件规定了锂电池化成分容微网直流总线测试系统的术语和定义、技术要求、试验方法、检验规则、标志、运输和储存等内容。
Requirements for lithium battery formation and capacitance testing based on microgrid DC bus
- ICS
- 19.080
- CCS
- C384
- 发布
- 2023-07-25
- 实施
- 2023-07-26
1 Scope This part of IEC 61010 specifies safety requirements for hand-held and hand-manipulated probe assemblies for electrical test and measurement, and their related accessories. These probe assemblies are for non-contact or direct electrical connection between a part and electrical test and measurement equipment. They can be fixed to the equipment or be detachable accessories for the equipment. This group safety publication focusing on safety essential requirements is primarily intended to be used as a product safety standard for the products mentioned in the scope, but is also intended to be used by technical committees in the preparation of publications for products similar to those mentioned in the scope of this group safety publication, in accordance with the principles laid down in IEC Guide 104 and lSO/lEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications and/or group safety publications in the preparation of its publications.
Safety requirements for electrical equipment for measurement, control, and laboratory use - Safety requirements for hand-held and hand-manipulated probe assemblies for electrical test and measurement
- ICS
- 19.080
- CCS
- 发布
- 2023-06-30
- 实施
- 2023-06-30
IEC 61010-031:2022 specifies safety requirements for hand-held and hand-manipulated probe assemblies for electrical test and measurement, and their related accessories. These probe assemblies are for non-contact or direct electrical connection between a part and electrical test and measurement equipment. They can be fixed to the equipment or be detachable accessories for the equipment. It has the status of a group safety publication in accordance with IEC Guide 104. This third edition cancels and replaces the second edition published in 2015, and Amendment 1:2018. IEC 61010-031 is a stand-alone standard. This edition includes the following significant technical changes with respect to the previous edition: the scope has been made succinct. General information from the scope of Edition 2 has been moved to a new Clause 4. Consequently, Clause 4 to Clause 8 of Edition 2 have been renumbered. Clause 9 of Edition 2 has been deleted; in Clause 2, normative references have been dated and new normative references have been added; in 3.1.4, the definition of probe tip has been modified; in 4.1, there is no longer any differentiation between high voltage and low voltage probe assemblies. Type C probe assemblies have been merged with Type B probe assemblies; in 4.1 d) "Kelvin" probes have been added to the list of probe assemblies as a new Type E and a new Figure 5; in 4.1 e), probes for voltage measurement without electrical connection to conductors have been added to the list of probe assemblies as a new Type F and a new Figure 6; in 4.2.1, spread of fire is no longer considered as a hazard; Subclause 4.4.2.5 from Edition 2 has been deleted; Subclause 4.4.4.3 from Edition 2 has been deleted; in 5.4.4.1 consideration has been given to spacings and impedance; in 6.1.1, removable parts of probe tips which bear markings are allowed; in 6.1.5, the voltage to be marked for measurement categories is the AC line-to-neutral or DC voltage; in 7.4.2, requirements for unmated connectors have been modified as follows: Table 2 has been modified and expanded, a calculation method for clearances of connectors above 20 kV has been defined, creepage distances have been aligned with clearances; in 7.4.3.1 and 7.4.3.5, requirements for IP2X probe tips with retractable sleeve have been added; in 7.4.3.2, Probe tips are now applicable to non-contact probe assemblies; in 7.5.2.3.2, the values of Table 5 have been modified; Status Approved Reference Document IEC 61010-031:2022 (EQV) IEC Technical Body IEC/TC 66 date of Availability (DAV) 2023-04-28 (7) ICS 19.080 - Electrical and electronic testing A-Deviation(s) Special National Condition(s)
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 031: Safety requirements for hand-held and hand-manipulated probe assemblies for electrical test and measurement
- ICS
- 19.080
- CCS
- 发布
- 2023-04-28 (7)
- 实施
- 2023-06-06 (7)
Application of measurement uncertainty to conformity assessment activities in the electrotechnical sector
- ICS
- 19.080
- CCS
- 发布
- 2023-04-12
- 实施
4 实验原理 5 试验条件 6 试验设备 7 样品 8 试验方法 9 试验结果的评定
Laser ranging method for high-temperature pressure indentation testing of wire and cable insulation and sheath
- ICS
- 19.080
- CCS
- M745
- 发布
- 2023-04-08
- 实施
- 2023-04-30
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 031: Safety requirements for hand-held and hand-manipulated probe assemblies for electrical test and me
- ICS
- 19.080
- CCS
- 发布
- 2022-12-22
- 实施
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 031: Safety requirements for hand-held and hand-manipulated probe assemblies for electrical test and me
- ICS
- 19.080
- CCS
- 发布
- 2022-12-22
- 实施
BS EN 61010-2-032. Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-032. Particular requirements for hand-held and hand-manipulated current sensors for electrical test and measurement
- ICS
- 19.080
- CCS
- 发布
- 2022-12-16
- 实施
- 2022-12-16
