共找到 1233 条与 铁管和钢管 相关的标准,共 83 页
Plain end steel tubes, welded and seamless —General tables of dimensions and masses per unit length
本部分规定了电站用马氏体耐热钢08Cr9W3Co3VNbCuBN(G115)对焊管件的术语和定义、订货内容、原材料要求、技术要求、制造、检验、缺陷处理、标志、表面防护、包装以及质量证明文件。 本部分适用于600℃以上电站锅炉和管道用马氏体耐热钢G115对焊管件,包括弯头、三通、异径管、接管座、封头等零部件,其它G115管件可参照执行。
Martensitic heat-resistant steel of 08Cr9W3Co3VNbCuBN(G115) for power station —Part 1:Butt-welding pipe fittings
Ductile iron pipes, fittings and accessories -- Requirements and test methods -- Part 1: PE coatings
Ductile iron pipes, fittings and accessories - Requirements and test methods for organic linings of ductile iron pipes and fittings - Part 2: Thermoplastic Acid Modified Polyolefin (TMPO) lining of pipes
Steel welded pipes. Defects of welded joints. Terms and definitions
1.1?This specification covers post-applied coatings, pavings, and linings for corrugated steel pipe and corrugated steel structural plate pipe, pipe-arches, and arches coated, paved, or lined with specified materials over either metallic coatings or metallic coatings with polyme
Standard Specification for Post-Applied Coatings, Pavings, and Linings for Corrugated Steel Sewer and Drainage Pipe
1.1 This specification covers grades of hot-formed welded and seamless high-strength low-alloy square, rectangular, round, or special shape structural tubing for welded, riveted, or bolted construction of bridges and buildings and for general structural purposes. When the steel is used in welded construction, the welding procedure shall be suitable for the steel and the intended service. 1.2 Square and rectangular tubing is produced with flats of 1 in. to 16 in. [25 mm to 405 mm] and a specified wall thickness of 0.095 in. to 1.0 in. [2.5 mm to 25 mm]. Round tubing is produced with diameters of 1 in. to 48 in. [25 mm to 1220 mm] and a specified wall thickness of 0.095 in. to 2.50 in. [2.5 mm to 65 mm]. 1.3 This specification covers the following grades: Ia, Ib, II, III, IV, V, VI and VII. 1.4 The text of this specification contains notes and footnotes that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements. 1.5 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Specification for Hot-Formed Welded and Seamless High-Strength Low-Alloy Structural Tubing
1.1?This practice covers recommended installation techniques for aluminum and stainless steel jacketing for thermal and acoustic pipe insulation operating at either above or below ambient temperatures and in both indoor and outdoor locations. This practice applies to materials m
Standard Practice for Installation of Aluminum and Stainless Steel Jacketing over Thermal Insulation on Pipe and Rigid Tubing
Carbon steel pipes for high pressure service
Final coating of ductile iron pipes, fittings and accessories
Non-destructive testing of steel tubes -- Part 3: Automated full peripheral flux leakage testing of seamless and welded (except submerged arc-welded) ferromagnetic steel tubes for the detection of longitudinal and/or transverse imperfections -- Amendment
Non-destructive testing of steel tubes -- Part 1: Automated electromagnetic testing of seamless and welded (except submerged arc-welded) steel tubes for the verification of hydraulic leaktightness -- Amendment 1: Change of dimensions of the reference notc
Non-destructive testing of steel tubes -- Part 12: Automated full peripheral ultrasonic thickness testing of seamless and welded (except submerged arc-welded) steel tubes -- Amendment 1: Change of acceptance criteria (ISO 10893-12:2011/Amd 1:2020)
Steel tubes and fittings-Symbols for use in specifications-Part 2:Square and rectangular hollow sections
Steel tubes and fittings-Symbols for use in specifications-Part 3:Tubular fittings with circular cross-section
Steel tubes and fittings-Symbols for use in specifications-Part 1:Tubes and tubular accessories with circular cross-section
Construction and installation of ductile iron pipeline system
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号