23.040.10 铁管和钢管 标准查询与下载

ASTM A746-18(2022) 球墨铸铁重力污水管

1.1 This specification covers 4 to 64 in. ductile iron gravity sewer pipe, centrifugally cast, with push-on joints. This specification may be used for pipe with other types of joints, as may be agreed upon at the time of purchase. 1.2 This specification covers trench load design procedures for both cement-lined pipe and flexible-lined pipe. Maximum depth of cover tables are included for both types of linings. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Ductile Iron Gravity Sewer Pipe

ASTM A716-18(2022) 球墨铸铁管

1.1 This specification covers 14 to 64 in. ductile iron culvert pipe, centrifugally cast. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazards caveat pertains only to the test methods portions, Sections 6 and 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Ductile Iron Culvert Pipe

ASTM A377-18(2022)e1 球墨铸铁压力管规范用标准索引

1.1 This index identifies specifications that cover ductile iron pressure pipe suitable for carrying water and other liquids under pressure. NOTE 1—The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Index of Specifications for Ductile Iron Pressure Pipe

ASTM A674-22 用于水或其他液体的球墨铸铁管的聚乙烯包装的标准实践

1.1 This practice covers materials and installation procedures for polyethylene encasement to be applied to underground installations of ductile iron pipe. It may also be used for polyethylene encasement of fittings, valves, and other appurtenances to ductile iron pipe systems. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.2.1 Important SI values are provided in brackets. Also, certain important SI values appear without brackets or parentheses. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Polyethylene Encasement for Ductile Iron Pipe

ASTM A139/A139M-22 电熔 (弧) 焊接钢管 (NPS 4及以上) 的标准规格

1.1 This specification covers five grades of electric-fusion (arc)-welded straight-seam or helical-seam steel pipe. Pipe of NPS 4 (Note 1) and larger with nominal (average) wall thickness of 1.0 in. [25.4 mm] and less are covered. Listing of standardized dimensions are for reference (Note 2). The grades of steel are pipe mill grades having mechanical properties which differ from standard plate grades. The pipe is intended for conveying liquid, gas, or vapor. NOTE 1—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.” NOTE 2—A comprehensive listing of standardized pipe dimensions is contained in ASME B36.10M. NOTE 3—The suitability of pipe for various purposes is somewhat dependent on its dimensions, properties, and conditions of service. For example, for high-temperature service see applicable codes and Specification A691. 1.2 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Electric-Fusion (Arc)-Welded Steel Pipe (NPS 4 and Over)

ASTM A1098/A1098M-18(2022) 带纹理表面的焊接奥氏体、铁素体、马氏体和双相不锈钢锅炉、过热器、冷凝器和热交换器管的标准规范

1.1 This specification covers average or minimum-wall thickness welded tubes made from various grades of austenitic, ferritic, martensitic and duplex stainless steel materials in which the (1) external tube surface, (2) internal tube surface, or (3) both internal and external tube surfaces have a textured configuration for improved heat transfer or fluid flow or both. Texture surface(s) are produced by cold forming a specified configuration on the surface(s) of base strip material, prior to welding. The produced welded textured tubes may be used in boilers, superheaters, condensers, evaporators, heat exchangers, and other similar heat transfer apparatus in diameters up to and including 1.5 in. [38 mm] for various wall thicknesses up to and including 0.079 in. [2 mm]. 1.2 The tubing sizes and thicknesses usually furnished to this specification are 0.375 in. [10 mm] inside diameter (ID) to 1.5 in. [38 mm] outside diameter and 0.020 to 0.079 in. [0.5 to 2 mm], inclusive, in wall thickness. Tubing having other dimensions may be furnished provided such tubes comply with all other requirements of this specification. 1.3 Optional supplementary requirements are provided and, when one or more of these are desired, each shall be so stated in the order. 1.4 Several grades of austenitic, ferritic, martensitic and duplex stainless steels are included in this specification. Not all alloys are suitable for all conditions. Selection will depend upon design and service requirements. 1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. 1.6 The following safety hazards statement pertains only to the test method and the Supplementary Requirements of this specification. A specific warning statement is given in the Supplementary Requirements. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Welded Austenitic, Ferritic, Martensitic and Duplex Stainless Steel Boiler, Superheater, Condenser, and Heat Exchanger Tubes with Textured Surface(s)

ASTM A587-22 化工用电阻焊低碳钢管标准规范

1.1 This specification2 covers electric-resistance-welded low-carbon steel pipe intended for use as process lines. 1.2 Pipe ordered under this specification shall be suitable for severe forming operations involving flanging in all sizes and bending to close radii up to and including NPS 4 [DN 100]. 1.3 This specification covers NPS 1⁄2 [DN 15] through NPS 10 [DN 250], plus additional sizes. The corresponding outside diameters and wall thicknesses for NPS 1⁄2 [DN 15] through 10 [DN 250] are listed in Table 1, as are the dimensions for the additional sizes. NOTE 1—The dimensionless designator NPS [DN] (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.” 1.4 Units—This specification is expressed in both inchpound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either inchpound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 The following precautionary caveat pertains only to the test method portion, Sections 7, 13, and 14, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Electric-Resistance-Welded Low-Carbon Steel Pipe for the Chemical Industry

ASTM A688/A688M-18(2022) 无缝和焊接奥氏体不锈钢给水加热管标准规范

1.1 This specification2 covers seamless and welded austenitic stainless steel feedwater heater tubes including those bent, if specified, into the form of U-tubes for application in tubular feed-water heaters. 1.2 The tubing sizes covered shall be 5⁄8 to 1 in. [15.9 to 25.4 mm] inclusive outside diameter, and average or minimum wall thicknesses of 0.028 in. [0.7 mm] and heavier. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless and Welded Austenitic Stainless Steel Feedwater Heater Tubes

BS ISO 4370:2022 水应用球墨铸铁管的环境生命周期评估和回收

1   Scope This document specifies the evaluation method of the environmental life cycle assessment ( E-LCA ) of ductile iron (DI) pipes used for water applications as specified in ISO 2531 and ISO 16631. This evaluation method, applicable to ductile iron pipe products, is based on concepts and methods developed in ISO 14040 and its application guidelines in ISO 14044.

Environmental life cycle assessment and recycling of ductile iron pipes for water applications

T/JSZX 002-2022 数字灯网 灯杆防腐技术规范

本文件给出了数字灯网产品灯杆防腐处理层的术语、定义、总体原则、基本要求、检测方法和检验要求。

Technical specification for anticorrosion of digital lamp net pole

KS D 3333-2022 管道输送用耐磨焊接钢管

Wear resistant welded steel pipe for pipe line transport

ASTM A53/A53M-22 焊接和无缝热浸镀锌/黑钢管标准规范

1.1 This specification2 covers seamless and welded black and hot-dipped galvanized steel pipe in NPS 1⁄8 to NPS 26 [DN 6 to DN 650] (Note 1), inclusive, with nominal wall thickness (Note 2) as given in Table X2.2 and Table X2.3. It shall be permissible to furnish pipe having other dimensions provided that such pipe complies with all other requirements of this specification. Supplementary requirements of an optional nature are provided and shall apply only when specified by the purchaser. NOTE 1—The dimensionless designators NPS (nominal pipe size) [DN (diameter nominal)] have been substituted in this specification for such traditional terms as “nominal diameter,” “size,” and “nominal size.” NOTE 2—The term nominal wall thickness has been assigned for the purpose of convenient designation, existing in name only, and is used to distinguish it from the actual wall thickness, which may vary over or under the nominal wall thickness. 1.2 This specification covers the following types and grades: 1.2.1 Type F—Furnace-butt-welded, continuous welded Grades A and B, 1.2.2 Type E—Electric-resistance-welded, Grades A and B, and 1.2.3 Type S—Seamless, Grades A and B. NOTE 3—See Appendix X1 for definitions of types of pipe. 1.3 Pipe ordered under this specification is intended for mechanical and pressure applications and is also acceptable for ordinary uses in steam, water, gas, and air lines. It is suitable for welding, and suitable for forming operations involving coiling, bending, and flanging, subject to the following qualifications: 1.3.1 Type F is not intended for flanging. 1.3.2 When pipe is required for close coiling or cold bending, Grade A is the preferred grade; however, this is not intended to prohibit the cold bending of Grade B pipe. 1.3.3 Type E is furnished either nonexpanded or cold expanded at the option of the manufacturer. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 The following precautionary caveat pertains only to the test method portion, Sections 7, 8, 9, 13, 14, and 15 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use. 1.6 The text of this specification contains notes or footnotes, or both, that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless

ISO 4370:2022 水用球墨铸铁管的环境生命周期评估和回收

This document specifies the evaluation method of the environmental life cycle assessment (E-LCA) of ductile iron (DI) pipes used for water applications as specified in ISO 2531 and ISO 16631. This evaluation method, applicable to ductile iron pipe products, is based on concepts and methods developed in ISO 14040 and its application guidelines in ISO 14044.

Environmental life cycle assessment and recycling of ductile iron pipes for water applications

T/SXMES 10-2022 T型接口输水用球墨铸铁管、管件

本文件规定了以离心铸造工艺类型或加工形式生产的球墨铸铁管（以下简称球墨铸铁管）、管件的术语和定义、分类、技术要求、试验方法、检查和验收、质量证明书、承接管件尺寸表。 本文件适用于包含有T型承口、插口或法兰，一般以内部和外部涂覆状态交货的管、管件，尺寸范围DN80-DN2600，流体温度0℃～50℃，适用范围如下： ——用于各种用途不同类型水的输送； ——有压或无压输送； ——地下或地上铺设。

Ductile iron pipes and fittings for water delivery with T-shaped joints

ASTM A798/A798M-22 下水道和其他应用用工厂制波纹钢管的安装标准实施规程

1.1 This practice covers procedures, soils, and soil placement for the proper installation of corrugated steel pipe and pipe-arches produced to Specification A760/A760M or A762/ A762M, in either trench or embankment installations. This practice also covers installation of corrugated steel pipe for alternative uses that do not involve backfilling or soil-structure interaction. 1.2 A typical trench installation and a typical embankment (projection) installation are shown in Figs. 1 and 2, respectively. The pipes described in this practice are manufactured in a factory and furnished to the job in lengths ordinarily from 10 to 30 ft [3 to 9 m], with 20 ft [6 m] being common, for field joining. This practice applies to structures designed in accordance with Practice A796/A796M. 1.3 Units—This practice is applicable to design in inchpound units as A798 or in SI units as A798M. Inch-pound units and SI units are not necessarily equivalent. SI units are shown in brackets in the text for clarity, but they are the applicable values when the installation is to be performed in accordance with A798M. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Installing Factory-Made Corrugated Steel Pipe for Sewers and Other Applications

ASTM E2096/E2096M-22 用远程现场试验对铁磁热交换器管进行现场检验的标准实施规程

1.1 This practice describes procedures to be followed during remote field examination of installed ferromagnetic heatexchanger tubing for baseline and service-induced discontinuities. 1.2 This practice is intended for use on ferromagnetic tubes with outside diameters from 0.500 to 2.000 in. [12.70 to 50.80 mm], with wall thicknesses in the range from 0.028 to 0.134 in. [0.71 to 3.40 mm]. 1.3 This practice does not establish tube acceptance criteria; the tube acceptance criteria must be specified by the using parties. 1.4 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for In Situ Examination of Ferromagnetic Heat-Exchanger Tubes Using Remote Field Testing

T/CASEI 009-2022 压力管道施工监督检验实施导则—公用管道

本文件规定了公用管道施工(施工包括安装、改造和重大修理)监督检验(以下简称监检)的术语和定义、受检单位、监检机构、监检人员、工作程序、现场监检项目和要求、现场施工质量保证体系实施状况评价和监检资料的要求。施工监检的对象包括安装过程、一次性更换相同介质的管段且总长度大于100m的改造或者重大修理过程(应急抢修的管道施工过程除外)。本文件适用于《特种设备目录》规定范围内,依据GB 50028《城镇燃气设计规范》、CJJ 34《城镇供热管网设计规范》、GB/T 38942《压力管道规范公用管道》设计的公用管道(包括燃气管道和热力管道)施工过程的监督检验。燃气系统中厂站内(不含调压站)的燃气管道和热力系统中厂站内(不包含热力站和热分配站)的热力管道,其施工监检专项要求按《压力管道施工监督检验实施导则—工业管道》执行。

Guidelines for supervision and inspection of pressure pipeline construction —Utility pipeline

T/CASEI 007-2022 压力管道施工监督检验实施导则—工业管道

本文件规定了工业管道施工监督检验(以下简称监检)的术语和定义、受检单位、监检机构、监检人员、工作程序、现场安装监检的要求、现场施工质量保证体系实施状况评价的要求。本文件适用于《特种设备目录》规定范围内工业管道(包括GC1级、GC2级、GCD级)的施工过程(包括管道安装、改造及重大修理)的监督检验工作。非金属管道的施工监检应符合本文件及附录A的规定。其中聚乙烯管施工监检的现场监检项目和要求还应符合《压力管道施工监督检验实施导则—公用管道》第8章中聚乙烯管的相关规定。火力发电厂界区内输送蒸汽、汽水两相介质的动力管道(不包括锅炉范围内管道)的施工监检应符合本文件及附录B的规定。长输管道及公用管道站场内的压力管道,施工监督检验应符合本文件及附录C的规定。站场内压力管道与线路管道一般以隔离阀为分界点。一次性更换相同介质的管道总长度大于100m的改造或者重大修理过程(应急抢修的管道施工过程除外)的施工监检按本文件执行。

Guidelines for supervision and inspection of pressure pipeline construction—industrial pipeline

T/CASEI 008-2022 压力管道施工监督检验实施导则—长输管道

本文件规定了长输管道施工监督检验(以下简称监检)的术语定义、受检单位、监检机构、监检人员、工作程序和现场监督检验的要求、现场施工质量保证体系实施状况评价的要求。本文件适用于《特种设备目录》规定范围内,依据GB 50251《输气管道工程设计规范》、GB 50253《输油管道工程设计规范》、GB/T 34275《压力管道规范长输管道》设计的长输管道(包括GA1、GA2)施工过程(包括管道安装、改造及重大修理)的监督检验工作。长输管道系统中的输油输气站场内的工艺管道参照《压力管道施工监督检验实施导则—工业管道》开展监督检验工作。输油输气站场的工艺管道与线路主管道的划分界限,一般以进出站截断阀(隔离阀)为分界线,或由管道使用单位确定。对于一次性更换相同介质的管段且总长度大于100m的改造或者重大修理过程(应急抢修的管道施工过程除外)也应按本文件执行。

Guidelines for supervision and inspection of pressure pipeline construction—long-distance pipeline

GSO ISO 8180:2022 球墨铸铁管道 现场应用的聚乙烯套管

This document specifies the characteristics of polyethylene film, commonly called polyethylene sleeving, used as additional protection against corrosion for ductile iron pipelines, particularly when laid in aggressive soil conditions. This film, the efficiency of which has been proved by experience, takes the form of a sheet or tube fitted around the pipes and fittings, on-site, immediately before pipe-laying.

Ductile iron pipelines — Polyethylene sleeving for site application