23.040.10 铁管和钢管 标准查询与下载

ASTM A268/A268M-22 通用无缝和焊接铁素体和马氏体不锈钢管标准规范

1.1 This specification2 covers a number of grades of nominal-wall-thickness, stainless steel tubing for general corrosion-resisting and high-temperature service. Most of these grades are commonly known as the “straight-chromium” types and are characterized by being ferromagnetic. Two of these grades, TP410 and UNS S 41500 (Table 1), are amenable to hardening by heat treatment, and the high-chromium, ferritic alloys are sensitive to notch-brittleness on slow cooling to ordinary temperatures. These features should be recognized in the use of these materials. 1.2 An optional supplementary requirement is provided, and when desired, shall be so stated in the order. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service

ASTM A312/A312M-22 无缝、焊接和深度冷加工奥氏体不锈钢管的标准规范

1.1 This specification2 covers seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipe intended for high-temperature and general corrosive service. 1.2 Grades TP304H, TP309H, TP309HCb, TP310H, TP310HCb, TP316H, TP321H, TP347H, and TP348H are modifications of Grades TP304, TP309Cb, TP309S, TP310Cb, TP310S, TP316, TP321, TP347, and TP348, and are intended for service at temperatures where creep and stress rupture properties are important. 1.3 Optional supplementary requirements are provided for pipe where a greater degree of testing is desired. These supplementary requirements call for additional tests to be made and, when desired, it is permitted to specify in the order one or more of these supplementary requirements. 1.4 Table X1.1 lists the standardized dimensions of welded and seamless stainless steel pipe as shown in ASME B36.19. These dimensions are also applicable to heavily cold worked pipe. Pipe having other dimensions is permitted to be ordered and furnished provided such pipe complies with all other requirements of this specification. 1.5 Grades TP321 and TP321H have lower strength requirements for pipe manufactured by the seamless process in nominal wall thicknesses greater than 3⁄8 in. [9.5 mm]. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. NOTE 1—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.” 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes

ISO 23991:2022 球墨铸铁管道的灌溉应用.产品设计和安装

This document specifies the design factor, technical requirements, test methods, installation technologies and operation advices applicable to ductile iron pipes, fittings and accessories used in piped irrigation applications. NOTE In this document, all pressures are relative pressures expressed in bars1). This document also specifies materials, dimensions and tolerances, mechanical properties and standard coatings of pipes, fittings and accessories. It also gives performance requirements for all components including joints. Joint design and gasket shapes are outside the scope of this document. This document applies to pipes, fittings and accessories cast by any type of foundry process or manufactured by fabrication of cast components.

Irrigation applications of ductile iron pipelines — Product design and installation

BS ISO 21052:2021 用于球墨铸铁管道的约束接头系统 限制长度的计算规则

1   Scope This document specifies a computation method used to determine the length of the ductile iron pipes to be restrained, when used for conveying raw water, drinking water, sewerage under pressure. This computation method takes into account all common pipeline route changes, including changes in the diameter of the pipeline itself and dead ends at the extremity of the pipeline, the outside diameter of the pipe, the system test pressure (to estimate the thrust), depth of cover, the characteristics of the soil surrounding the pipe and trench backfilling methods for a worldwide usage. The characteristics of the restrained joint are not covered by this document but can also be considered to determine the restraining length using any appropriate method. The computation method defined in this document is applicable to all types of restrained joint systems, with their operating pressure ratings of ductile iron pipelines complying with ISO 2531, ISO 7186 and ISO 16631. NOTE 1 ISO 10804 deals with actual design of the joint for various operating pressures of the pipeline. NOTE 2 National standards or established calculation methods can be used instead of this ISO standard.

Restrained joint systems for ductile iron pipelines. Calculation rules for lengths to be restrained

ASTM A790/A790M-22 无缝和焊接铁素体/奥氏体不锈钢管标准规范

1.1 This specification2 covers seamless and straight-seam welded ferritic/austenitic steel pipe intended for general corrosive service, with particular emphasis on resistance to stress corrosion cracking. These steels are susceptible to embrittlement if used for prolonged periods at elevated temperatures. 1.2 Optional supplementary requirements are provided for pipe when a greater degree of testing is desired. These supplementary requirements call for additional tests to be made and, when desired, one or more of these may be specified in the order. 1.3 Appendix X1 of this specification lists the dimensions of welded and seamless stainless steel pipe as shown in ANSI B36.19. Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of this specification. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the M designation of this specification is specified in the order. NOTE 1—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as nominal diameter, size, and nominal size. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Pipe

ASTM A1103/A1103M-16(2022) 汽车赛车用无缝冷加工碳钢结构框架管标准规范

1.1 This specification is for seamless cold-finished carbon steel round structural frame tubing for automotive racing applications. The chemical requirements are listed in Table 1. Tubing may be used for other applications requiring similar tolerances and properties. The specification includes requirements for heat treatment and mechanical properties to meet the needs for the application. The tubing is intended to be bent and joined by welding. The welding procedure shall be suitable for the grade, the condition of the components, and the intended service. 1.2 The tubing outside diameter size range is from 0.625 to

Standard Specification for Seamless Cold-Finished Carbon Steel Structural Frame Tubing for Automotive Racing Applications

ASTM A1053/A1053M-12(2022) 焊接铁素体-马氏体不锈钢管标准规范

1.1 This specification covers seam welded ferriticmartensitic (dual phase) stainless steel pipe intended for abrasive and general corrosion service, manufactured with or without the addition of filler metal. Nominal sizes are NPS 2 to NPS 36 inclusive, with nominal (average) wall thickness up to 0.75-in. (19 mm). 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents. Therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation is specified in the order. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Welded Ferritic-Martensitic Stainless Steel Pipe

ASTM A209/A209M-03(2022) 无缝碳钼合金钢锅炉和过热器管标准规范

1.1 This specification2 covers several grades of minimumwall-thickness, seamless, carbon-molybdenum alloy-steel, boiler and superheater tubes. 1.2 This specification covers tubes 1⁄2 to 5 in. [12.7 to 127 mm] inclusive, in outside diameter and 0.035 to 0.500 in. [0.9 to 12.7 mm], inclusive, in minimum wall thickness. 1.3 An optional supplementary requirement is provided and, when desired, shall be so stated in the order. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater Tubes

ASTM E213-22 金属管和管子的超声波检验的标准实施规程

1.1 This practice2 covers a procedure for detecting discontinuities in metal pipe and tubing during a volumetric examination using ultrasonic methods. Specific techniques of the ultrasonic method to which this practice applies include pulse-reflection techniques, both contact and non-contact (for example, as described in Guide E1774 and Practice E1816), and angle beam immersion techniques, both conventional and phased array. Artificial reflectors consisting of longitudinal, and, when specified by the using party or parties, transverse reference notches placed on the surfaces of a reference standard are employed as the primary means of standardizing the ultrasonic system. 1.2 This practice is intended for use with tubular products having outside diameters approximately 1⁄2 in. (12.7 mm) and larger, provided that the examination parameters comply with and satisfy the requirements of Section 11. These procedures have been successful with smaller sizes. These may be specified upon contractual agreement between the using parties. These procedures are intended to ensure that proper beam angles and beam shapes are used to provide full volume coverage of pipes and tubes, including those with low ratios of outside diameter-to-wall thickness, and to avoid spurious signal responses when examining small-diameter, thin-wall tubes. 1.3 The procedure in Annex A1 is applicable to pipe and tubing used in nuclear and other special and safety applications. The procedure in Annex A2 may be used to determine the helical scan pitch. 1.4 This practice does not establish acceptance criteria; they must be specified by the using party or parties. 1.5 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Ultrasonic Testing of Metal Pipe and Tubing

ASME B36.19-2022 不锈钢管

Stainless Steel Pipe

T/CFA 02010202-4-2021 非开挖管道施工用球墨铸铁顶管

本文件规定了顶管的术语和定义，球墨铸铁顶管结构、接口尺寸、外形及允许偏差，技术要求，试验方法，检验规则，标志、包装、存放、吊装、运输。

Ductile iron jacking pipe for trenchless pipeline construction

DIN 4927:2021 用于提升水的带法兰的钢上升管 公称直径 50 至 200

This document specifies dimensions, materials and requirements for flanged steel rising pipes. The pipes serve the raising of water from wells or tanks.

Flanged steel rising pipes for raising of water - Nominal diameter 50 to 200

ISO 21052:2021 球墨铸铁管道的约束连接系统.约束长度的计算规则

This document specifies a computation method used to determine the length of the ductile iron pipes to be restrained, when used for conveying raw water, drinking water, sewerage under pressure. This computation method takes into account all common pipeline route changes, including changes in the diameter of the pipeline itself and dead ends at the extremity of the pipeline, the outside diameter of the pipe, the system test pressure (to estimate the thrust), depth of cover, the characteristics of the soil surrounding the pipe and trench backfilling methods for a worldwide usage. The characteristics of the restrained joint are not covered by this document but can also be considered to determine the restraining length using any appropriate method. The computation method defined in this document is applicable to all types of restrained joint systems, with their operating pressure ratings of ductile iron pipelines complying with ISO 2531, ISO 7186 and NOTE 1 ISO 10804 deals with actual design of the joint for various operating pressures of the pipeline. NOTE 2 National standards or established calculation methods can be used instead of this ISO standard.

Restrained joint systems for ductile iron pipelines — Calculation rules for lengths to be restrained

ASTM A450/A450M-21 碳钢管和低合金钢管一般要求的标准规范

1.1 This specification2 covers a group of requirements which, with the exceptions of 6.3 and Sections 7, 8, 19, 20, 21, 22, 23, 24, and 25, are mandatory requirements to the following ASTM tubular product specifications:3 Title of Specification ASTM DesignationA Electric-Resistance-Welded Carbon Steel and CarbonManganese Steel Boiler Tubes A178/A178M Seamless Cold-Drawn Low-Carbon Steel HeatExchanger and Condenser Tubes A179/A179M Seamless Carbon Steel Boiler Tubes for High-Pressure Service A192/A192M Seamless Medium-Carbon Steel Boiler and Superheater Tubes A210/A210M Electric-Resistance-Welded Carbon Steel HeatExchanger and Condenser Tubes A214/A214M Seamless and Electric-Welded Low-Alloy Steel Tubes A423/A423M Specification for Seamless and Welded Carbon Steel Heat-Exchanger Tubes with Integral Fins A498/A498M Seamless Cold-Drawn Carbon Steel Feedwater Heater Tubes A556/A556M Seamless, Cold-Drawn Carbon Steel Tubing for Hydraulic System Service A822/A822M A These designations refer to the latest issue of the respective specifications. 1.2 One or more of Sections 6.3, 7, 8, 19, 20, 21, 22, 22.1, 24, and 25 apply when the product specification or purchase order has a requirement for the test or analysis described by these sections. 1.3 In case of conflict between a requirement of the product specification and a requirement of this general requirement specification only the requirement of the product specification need be satisfied. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for General Requirements for Carbon and Low Alloy Steel Tubes

ASTM A511/A511M-21a 无缝不锈钢机械管和空心棒的标准规范

1.1 This specification covers seamless stainless tubing for use in mechanical applications or as hollow bar for use in the production of hollow components such as, but not limited to nozzles, reducers, and couplings by machining where corrosion-resistant or high-temperature strength is needed. The grades covered are listed in Table 1 , Table 2, and Table 3. 1.2 This specification covers seamless cold-finished mechanical tubing and hollow bar and seamless hot-finished mechanical tubing and hollow bar in sizes up to 123⁄4 in. [325 mm] in outside nominal diameter (for round tubing) with wall thicknesses or inside diameters as required. 1.3 Tubes for mechanical applications shall be furnished in one of the following shapes, as specified by the purchaser: round, square, rectangular, or special. Tubes to be used as hollow bar shall be furnished in round shape. 1.4 Optional supplementary requirements are provided and when desired, shall be stated in the order. 1.5 The values stated in inch-pound units are to be regarded as the standard. Within the text, the SI units are shown in square brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Stainless Steel Mechanical Tubing and Hollow Bar

ASTM A335/A335M-21a 高温设备用无缝铁素体合金钢管标准规范

Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service

ASTM A972/A972M-00(2021) 熔结环氧涂层管桩的标准规范

1.1 This specification covers pipe piles with protective fusion-bonded epoxy powder coating applied by the electrostatic spray, flocking, or fluidized bed process. NOTE 1—The coating applicator is identified throughout this specification as the manufacturer. 1.2 Other organic coatings may be used provided they meet the requirements of this specification. 1.3 Requirements for the powder coating are contained in Annex A1. 1.4 This specification is applicable for orders in either SI units (as Specification A972M) or inch-pound units [as Specification A972]. The values stated in either SI or inch-pound units are to be regarded as standard. Within the text, the inch-pound units are shown in brackets. 1.5 The following precautionary statement refers to the test method portion only, Section 8, of this standard: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Fusion Bonded Epoxy-Coated Pipe Piles

ASTM A213/A213M-21b 无缝铁素体和奥氏体合金钢锅炉、过热器和热交换器管的标准规范

Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes

NF E86-700-2/A8*NF EN 13480-2 V1/A8:2021 金属工业管道 第2部分：材料

Metallic industrial piping - Part 2 : materials

ASTM A334/A334M-04a(2021) 低温设备用无缝和焊接碳和合金钢管的标准规范

1.1 This specification2 covers several grades of minimumwall-thickness, seamless and welded, carbon and alloy-steel tubes intended for use at low temperatures. Some product sizes may not be available under this specification because heavier wall thicknesses have an adverse affect on low-temperature impact properties. 1.2 Supplementary Requirement S1 of an optional nature is provided. This shall apply only when specified by the purchaser. NOTE 1—For tubing smaller than 1⁄2 in. [12.7 mm] in outside diameter, the elongation values given for strip specimens in Table 1 shall apply. Mechanical property requirements do not apply to tubing smaller than 1⁄8 in. [3.2 mm] in outside diameter and with a wall thickness under 0.015 in. [0.4 mm]. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless and Welded Carbon and Alloy-Steel Tubes for Low-Temperature Service