23.040.10 铁管和钢管 标准查询与下载

ASTM A334/A334M-04a(2021) 低温设备用无缝和焊接碳和合金钢管的标准规范

1.1 This specification2 covers several grades of minimumwall-thickness, seamless and welded, carbon and alloy-steel tubes intended for use at low temperatures. Some product sizes may not be available under this specification because heavier wall thicknesses have an adverse affect on low-temperature impact properties. 1.2 Supplementary Requirement S1 of an optional nature is provided. This shall apply only when specified by the purchaser. NOTE 1—For tubing smaller than 1⁄2 in. [12.7 mm] in outside diameter, the elongation values given for strip specimens in Table 1 shall apply. Mechanical property requirements do not apply to tubing smaller than 1⁄8 in. [3.2 mm] in outside diameter and with a wall thickness under 0.015 in. [0.4 mm]. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless and Welded Carbon and Alloy-Steel Tubes for Low-Temperature Service

ASTM A501/A501M-21 热成型焊接和无缝碳钢结构管的标准规范

1.1?This specification covers black and hot-dipped galvanized hot-formed welded and seamless carbon steel square, round, rectangular, or special shape structural tubing for welded, riveted, or bolted construction of bridges and buildings, and for general structural purposes. 1.

Standard Specification for Hot-Formed Welded and Seamless Carbon Steel Structural Tubing

GSO ISO 16132:2021 球墨铸铁管和配件 水泥砂浆衬里密封层

ISO 16132:2016 specifies the requirements for seal coatings for factory application to the surfaces of cement mortar linings, which are factory applied to the interior of ductile iron pipes and fittings. It provides the performance requirements for short-term sealing efficiency, long-term durability and cyclic pressure, as well as the routine testing requirements for visual appearance, coating thickness and adhesion. ISO 16132:2016 is applicable to products for potable and other water applications.

Ductile iron pipes and fittings — Seal coats for cement mortar linings

OENORM EN 10357-2021 食品和化学工业用奥氏体、奥氏体-铁素体和铁素体纵焊不锈钢管

Austenitic, austenitic-ferritic and ferritic longitudinally welded stainless steel tubes for the food and chemical industry

GSO ISO 8179-2:2021 球墨铸铁管、管件、附件及其接头 外锌基涂层 第2部分：富锌漆

ISO 8179-2:2017 specifies an external protective coating system which is factory-applied to ductile iron pipeline components as specified in ISO 2531, ISO 7186 and ISO 16631. This coating system comprises a zinc-rich paint followed by a finishing layer that can be bituminous paint or synthetic resin compatible with zinc rich paint coating. NOTE ISO 8179-1 addresses metallic zinc-based coatings.

Ductile iron pipes, fittings, accessories and their joints — External zinc-based coating — Part 2: Zinc-rich paint

GSO ASTM A377:2021 球墨铸铁压力管道规格标准索引

-

Standard Index of Specifications for Ductile Iron Pressure Pipe

GSO EN 10312:2021 用于输送水性液体（包括人类用水）的焊接不锈钢管 技术交货条件

This European Standard specifies the technical delivery conditions for light gauge welded stainless steel tubes, primarily for water application, including water intended for human consumption, supplied in straight lengths and suitable for connection by adhesive bonding, capillary fittings, compression fittings, press fittings or by inert gas welding. The standard covers the size range from 6 mm to 159 mm outside diameter in two grades of stainless steel from EN 10088-2.

Welded stainless steel tubes for the conveyance of aqueous liquids including water for human consumption – Technical delivery conditions

GSO ISO 8179-1:2021 球墨铸铁管、配件、附件及其接头 外锌基涂层 第1部分：带饰面层的金属锌

ISO 8179-1:2017 specifies an external protective coating system which is factory applied to ductile iron pipeline components as specified in ISO 2531, ISO 7186 and ISO 16631. This coating system comprises an electro-deposited metallic zinc-based coating of - pure metallic zinc with a purity of 99,99 %, - zinc and aluminium alloy with or without other metals, or - other zinc alloys followed by a finishing layer that can be bituminous paint or synthetic resin compatible with zinc-based coating. NOTE ISO 8179-2 deals with zinc-rich paint coating.

Ductile iron pipes, fittings, accessories and their joints — External zinc-based coating — Part 1: Metallic zinc with finishing layer

ASTM F1545-15a(2021) 塑料衬里黑色金属管、配件和法兰的标准规范

1.1 This specification covers factory-made plastic-lined ferrous metal pipe, fittings, and flanges intended primarily for conveying corrosive fluids. Requirements for materials, workmanship, dimensions, design, fabrication, working pressure and temperatures, test methods, qualification requirements, and markings are included. 1.1.1 This specification does not define the suitability of different liner materials to various chemical and operating environments. Refer to the manufacturer’s chemical resistance data for suitability recommendations. 1.1.2 This specification does not include products coated with plastics. 1.2 This specification covers plastic-lined pipe, flanges, and fittings as listed in Table 1. Pressure limitations shall be in accordance with ASME B16 Standards, except reduced pressure limitations may be established by the manufacturer, considering both pressure and temperature limitations of the ferrous metal housing and the sealing ability of the liner. NOTE 1—In this specification, propylene plastics cover those materials defined as both polypropylene plastics and propylene plastics in Terminology F412. Both materials are identified as “PP” on the product. Note that this is at variance with Terminology D1600, where “PP” is the abbreviation for polypropylene. 1.3 The plastic-lined flanged pipe and fitting assemblies are limited to temperatures shown in Table 2. End users should consult with manufacturers as to the likely result of using a particular lined piping component at temperatures below the rated minimum. NOTE 2—The temperature limitations are based on noncorrosive test conditions. Use in specific aggressive environments may alter temperature limitations. In such instances, specific temperature limits shall be established by mutual agreement between the purchaser and the manufacturer. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges

GSO ASTM A746:2021 球墨铸铁重力污水管标准规范

This specification covers ductile iron gravity sewer pipe centrifugally cast with push-on joints. This also covers trench load design procedures for both cement-lined pipe and flexible-lined pipe. Maximum depths of cover tables are included for both types of linings. Each pipe shall be subjected to a hydrostatic test and maybe performed either before or after the outside coating and inside coating have been applied, but shall be performed before the application of cement-mortar lining or of a special lining. The standard acceptance tests and additional control tests shall also be performed.

Standard Specification for Ductile Iron Gravity Sewer Pipe

T/CNEA 101.22-2021 压水堆承压部件 材料 第22部分：高温用无缝铁素体合金钢管

本文件是T/CNEA 101《压水堆承压部件 材料》的第22部分。本文件共计16章，其中，1-3章为规范性条款，4-16章为压水堆承压部件 材料 第22部分：高温用无缝铁素体合金钢管主要内容。主要内容包括：订货要求、制造、化学成分、工艺质量、表面质量和外观、成品分析、拉伸性能、直径允许偏差、壁厚允许偏差、水压试验、无损检测、要求的力学性能试验、质量证明文件和产品标志。

PWR pressure boundary components—Material— Part 22:Seamless ferritic alloy-steel pipe for high-temperature service

T/CNEA 101.33-2021 压水堆承压部件 材料 第33部分：奥氏体不锈钢无缝钢管

本文件是T/CNEA 101《压水堆承压部件 材料》的第33部分。本文件共计15章，其中，1-3章为规范性条款，4-15章为压水堆承压部件 材料 第33部分：奥氏体不锈钢无缝钢管主要内容。主要内容包括：订货要求、制造、热处理、化学成分、壁厚的允许偏差、拉伸性能、要求的力学性能试验、水压试验或无损检测、长度、工艺质量、表面质量和外观、质量证明文件和产品标志。

PWR pressure boundary components—Material— Part 33:Seamless austenitic stainless steel pipes

T/CNEA 101.21-2021 压水堆承压部件 材料 第21部分：碳钢、铁素体合金钢和奥氏体合金钢管通用要求

本文件是T/CNEA 101《压水堆承压部件 材料》的第21部分。本文件共计28章，其中，1-3章为规范性条款，4-28章为压水堆承压部件 材料 第21部分：碳钢、铁素体合金钢和奥氏体合金钢管通用要求主要内容。主要内容包括：订货要求、冶炼、化学成分、力学性能、标准质量、壁厚允许偏差、外径允许偏差、长度允许偏差、电阻焊接钢管毛边高度允许偏差、直度和表面质量、焊补、复试、重新热处理、试样、压扁试验、反向压扁试验、扩口试验、卷边试验、水压试验、水下气压试验、无损检测、检查、质量证明文件、产品标志和包装和装运。

PWR pressure boundary components—Material— Part 21:General requirements for carbon, ferritic alloy, and austenitic alloy steel tubes

T/CNEA 101.20-2021 压水堆承压部件 材料 第20部分：高温用无缝碳钢公称管

本文件是T/CNEA 101《压水堆承压部件 材料》的第20部分。本文件共计22章，其中，1-3章为规范性条款，4-22章为压水堆承压部件 材料 第20部分：高温用无缝碳钢公称管主要内容。主要内容包括：订货要求、制造、热处理、化学成分、拉伸试验、弯曲试验、压扁试验、水压试验、无损检测、管接头、质量与尺寸的允许偏差、长度、工艺质量、表面质量和外观、管端加工、试验规则、复试、试样及试验方法、质量证明文件和产品标志。

PWR pressure boundary components—Material— Part 20:Carbon-steel Seamless pipe for high-temperature applications

T/CNEA 101.26-2021 压水堆承压部件 材料 第26部分：中、高温用锻制合金钢管道配件

本文件是T/CNEA 101《压水堆承压部件 材料》的第26部分。本文件共计15章，其中，1-3章为规范性条款，4-15章为压水堆承压部件 材料 第26部分：中、高温用锻制合金钢管道配件主要内容。主要内容包括：订货要求、制造、热处理、化学成分、拉伸试验、硬度试验、水压试验、尺寸、公差和表面质量、焊接修补、检查、质量证明文件和标志。

PWR pressure boundary components—Material— Part 26:Piping fittings of wrought alloy steel for moderate and high-temperature service

T/CNEA 101.34-2021 压水堆承压部件 材料 第34部分：高温中央电站用奥氏体不锈钢无缝钢管

本文件是T/CNEA 101《压水堆承压部件 材料》的第34部分。本文件共计11章，其中，1-3章为规范性条款，4-11章为压水堆承压部件 材料 第34部分：高温中央电站用奥氏体不锈钢无缝钢管主要内容。主要内容包括：订货要求、制造、化学成分、力学性能、工艺质量、表面质量和外观、水压试验或无损检测、质量证明文件和标志。

PWR pressure boundary components—Material— Part 34:Seamless austenitic steel pipe for high-temperature centralstation service

T/CNEA 101.19-2021 压水堆承压部件 材料 第19部分：专门用途碳钢和合金钢公称管通用要求

本文件是T/CNEA 101《压水堆承压部件 材料》的第19部分。本文件共计23章，其中，1-3章为规范性条款，4-23章为压水堆承压部件 材料 第19部分：专门用途碳钢和合金钢公称管通用要求主要内容。主要内容包括：订货要求、冶炼方法、化学成分、拉伸性能、无缝钢管质量允许偏差、壁厚允许偏差、内径的允许偏差、外径的允许偏差、长度允许偏差、管端、直线度、焊补、复试、重新热处理、压扁试验、水压试验、质量证明文件、检查、拒收和产品标志。

PWR pressure boundary components—Material— Part 19:General Requirements of carbon steel and low-alloy steel pipes

T/CNEA 101.32-2021 压水堆承压部件 材料 第32部分：热交换器用奥氏体不锈钢无缝钢管

本文件是T/CNEA 101《压水堆承压部件 材料》的第32部分。本文件共计15章，其中，1-3章为规范性条款，4-15章为压水堆承压部件 材料 第32部分：热交换器用奥氏体不锈钢无缝钢管主要内容。主要内容包括：订货要求、制造、化学成分、批的定义、力学性能、工艺性能、水压试验或无损检测、工艺要求、规定壁厚的允许偏差、表面状态、质量证明文件和标志。

PWR pressure boundary components—Material— Part 32:Seamless austenitic stainless steel tubes for heat-exchanger

OENORM EN 10216-5-2021 压力用无缝钢管 交货技术条件 第5部分：不锈钢管

Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes

OENORM EN ISO 10893-3:2021 钢管的无损检测 第3部分：用于检测纵向和/或横向缺陷的无缝和焊接（埋弧焊除外）铁磁钢管的自动全周漏磁通检测（ISO 10893-3:2

Non-destructive testing of steel tubes - Part 3: Automated full peripheral flux leakage testing of seamless and welded (except submerged arc-welded) ferromagnetic steel tubes for the detection of longitudinal and/or transverse imperfections (ISO 10893-3:2