25.220.60 标准查询与下载

23/30477702 DC BS EN 13523-29 卷材涂层金属 测试方法 第29部分：耐环境污染性（沾污和剥离）

BS EN 13523-29. Coil coated metals. Test methods - Part 29. Resistance to environmental soiling (Dirt pick-up and striping)

T/QGCML 818-2023 轨道交通车辆表面保护聚脲涂层

本文件规定了轨道交通车辆表面保护聚脲涂层的术语和定义、分类和标记、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于轨道交通车辆表面保护聚脲涂层的生产及检验。

Polyurea Coating for Surface Protection of Rail Transit Vehicles

T/QGCML 819-2023 轨道交通车辆表面保护聚脲涂层试验方法

本文件规定了轨道交通车辆表面保护聚脲涂层试验方法的术语和定义、试验条件、试验设备、涂膜制备、试验方法、试验报告。 本文件适用于轨道交通车辆表面保护聚脲涂层试验和检验。

Test method of polyurea coating for surface protection of rail transit vehicles

ASTM D1474/D1474M-13(2023) 有机涂层压痕硬度的标准试验方法

1.1 These test methods cover the determination of the indentation hardness of organic materials such as dried paint, varnish, and lacquer coatings, when applied to an acceptable plane rigid surface, for example, metal or glass. 1.2 Two methods are covered as follows: Sections Method A—Knoop Indentation Hardness 6 – 12 Method B—Pfund Indentation Hardness 13 – 19 1.3 Method A, which has the greater precision, provides hardness values in terms of Knoop Hardness Number (KHN). Method B provides hardness in terms of Pfund Hardness Number (PHN). Although the hardness value scales of these methods differ, the methods agree in the ranking of coating hardness. 1.4 Test Method A of these test methods is similar in content (but not technically equivalent) to ISO 6441-1 and ISO 6441-2. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.6 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Indentation Hardness of Organic Coatings

T/CCTAS 41-2022 交通工程钢构件熔融纳米环氧复合涂层防腐技术要求

本文件规定了交通工程钢构件熔融纳米环氧复合涂层的术语和定义、涂层分类、技术要求、试验方 法。

Technical requirement for anticorrosion of melting nano-epoxy composite coating for traffic engineering steel members

ASTM D3003-01(2022) 金属基底上有机涂层耐压力斑点和阻塞性的标准试验方法

1.1 This test method covers determination of the pressure mottling and sticking, or blocking resistance of organic coatings applied to coil-coated or factory-coated metal prior to fabrication. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Pressure Mottling and Blocking Resistance of Organic Coatings on Metal Substrates

ASTM F1664-08(2022) 与链式围栏一起使用的聚氯乙烯（PVC）和其他符合要求的有机聚合物涂层钢丝

1.1 This specification covers PVC and other conforming organic polymer-coated steel tension wire for use with chain link fence. PVC and other organic polymer coatings hereinafter will be designated as polymer coating. 1.2 Tension wire, produced from three classes of wire coatings, is covered as follows: 1.2.1 Class 1, consisting of a polymer coating extruded over zinc-coated or aluminum-coated or zinc-5 % aluminummischmetal alloy-coated steel wire; 1.2.2 Class 2a, consisting of a polymer coating extruded and adhered to zinc-coated or aluminum-coated or zinc-5 % aluminum-mischmetal alloy-coated steel wire; and 1.2.3 Class 2b, consisting of a polymer coating fused and adhered to zinc-coated or aluminum-coated or zinc-5 % aluminum-mischmetal alloy-coated steel wire. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Poly(Vinyl Chloride) (PVC) and Other Conforming Organic Polymer-Coated Steel Tension Wire Used with Chain-Link Fence

ASTM F1665-08(2022) 与链式围栏一起使用的聚氯乙烯（PVC）和其他符合要求的有机聚合物涂层钢刺钢丝

1.1 This specification covers PVC and other conforming organic polymer-coated steel barbed wire consisting of two polymer-coated strands, with four-point barbs of zinc-coated steel or aluminum alloy wire. PVC and other organic polymer coatings hereinafter will be designated as polymer coating. 1.2 Barbed wire strand wire, produced from three classes of wire coatings, is covered as follows: 1.2.1 Class 1, consisting of a polymer coating extruded over zinc-coated or aluminum-coated or zinc-5 % aluminummischmetal alloy-coated steel wire; 1.2.2 Class 2a, consisting of a polymer coating extruded and adhered to zinc-coated or aluminum-coated or zinc-5 % aluminum-mischmetal alloy-coated steel wire; and 1.2.3 Class 2b, consisting of a polymer coating fused and adhered to zinc-coated or aluminum-coated or zinc-5 % aluminum-mischmetal alloy-coated steel wire. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Poly(Vinyl Chloride) (PVC) and Other Conforming Organic Polymer-Coated Steel Barbed Wire Used With Chain-Link Fence

BS ISO 18768-2:2022 铝及其合金上的有机涂层 铝上装饰性和保护性有机涂层的规定方法 液体涂层

1   Scope This document specifies methods for specifying decorative and protective powder coatings on aluminium and its alloys. It defines the characteristic properties of powder coatings and provides testing methods with minimum performance requirements, with reference to the application and the aggressiveness of the environment in which the coated aluminium exists. This document does not apply to coil coatings on aluminium.

Organic coatings on aluminium and its alloys. Methods for specifying decorative and protective organic coatings on aluminium - Liquid coatings

BS ISO 18768-1:2022 铝及其合金上的有机涂层 铝上装饰性和保护性有机涂层的规定方法 粉末涂料

1   Scope This document specifies methods for specifying decorative and protective powder coatings on aluminium and its alloys. It defines the characteristic properties of powder coatings and provides testing methods with minimum performance requirements, with reference to the application and the aggressiveness of the environment in which the coated aluminium exists. This document does not apply to coil coatings on aluminium.

Organic coatings on aluminium and its alloys. Methods for specifying decorative and protective organic coatings on aluminium - Powder coatings

ASTM D2197-16(2022) 用刮擦法测定有机涂层附着力的标准试验方法

1.1 This test method covers the determination of the adhesion of organic coatings such as paint, varnish, and lacquer when applied to smooth, flat (planar) panel surfaces. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion

ISO 18768-2:2022 铝及其合金上的有机涂层.铝上装饰性和保护性有机涂层的规定方法.第2部分:液体涂层

This document specifies methods for specifying decorative and protective organic coatings on aluminium and its alloys. It defines the characteristic properties of organic liquid coatings and provides testing methods with minimum performance requirements, with reference to the application and the aggressiveness of the environment in which the painted aluminium exists. This document is applicable to aluminium products with liquid coatings for general applications, and liquid coatings mainly processed by electrostatic liquid spraying, air spraying or airless spraying. This document does not apply to coil coatings on aluminium.

Organic coatings on aluminium and its alloys — Methods for specifying decorative and protective organic coatings on aluminium — Part 2: Liquid coatings

ISO 18768-1:2022 铝及其合金上的有机涂层.铝上装饰性和保护性有机涂层的规定方法.第1部分:粉末涂层

This document specifies methods for specifying decorative and protective powder coatings on aluminium and its alloys. It defines the characteristic properties of powder coatings and provides testing methods with minimum performance requirements, with reference to the application and the aggressiveness of the environment in which the coated aluminium exists. This document does not apply to coil coatings on aluminium.

Organic coatings on aluminium and its alloys — Methods for specifying decorative and protective organic coatings on aluminium — Part 1: Powder coatings

ASTM D6132-13(2022) 使用超声波涂层测厚仪无损测量应用有机涂层干膜厚度的标准试验方法

1.1 This test method describes the use of ultrasonic film thickness gages to measure accurately and nondestructively the dry film thickness of organic coatings applied over a substrate of dissimilar material. Measurements may be made on field structures, on commercially manufactured products, or on laboratory test specimens. These types of gages can accurately measure the dry film thickness of organic coatings on a variety of substrates such as concrete, wood, wallboard, plastic, fiber composites and metal. 1.2 This test method is not applicable to coatings that will be readily deformable under load of the measuring instrument as the instrument probe is placed directly on the coating surface to take a reading. 1.3 The effective range of instruments using the principle of ultrasonics is limited by gage design. A thickness range of 8 µm to 7.60 mm (0.3 to 300 mils) has been demonstrated. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Coating Thickness Gage

ASTM D968-22 用落砂法测定有机涂层耐磨性的标准试验方法

1.1 These test methods cover the determination of the resistance of organic coatings to abrasion produced by abrasive falling onto coatings applied to a plane rigid surface, such as a metal or glass panel. 1.2 Two test methods based on different abrasives are covered as follows: Sections Method A—Falling Sand Abrasion Test 6 – 13 Method B—Falling Silicon Carbide Abrasion Test 14 – 21 1.3 These methods should be restricted to testing in only one laboratory when numerical values are used because of the poor reproducibility of the methods (see 13.1.2 and 21.1.2). Interlaboratory agreement is improved significantly when ranking is used in place of numerical values. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses after SI units are for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive

ASTM D6991-17(2022) 用悬臂（梁）法测量有机涂层内应力的标准试验方法

1.1 This test method covers the procedure for measurements of internal stresses in organic coatings by using the cantilever (beam) method. 1.2 This method is appropriate for the coatings for which the modulus of elasticity of substrate (Es) is significantly greater than the modulus of elasticity of coating (Ec) and for which the thickness of substrate is significantly greater than thickness of coating (see Note 7 and Note 8). 1.3 The stress values are limited by the adhesion values of coating to the substrate and by the tensile strength of the coating, or both. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and to determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measurements of Internal Stresses in Organic Coatings by Cantilever (Beam) Method

ASTM D3363-22 铅笔试验法测定薄膜硬度的标准试验方法

1.1 This test method covers a procedure for rapid, inexpensive determination of the film hardness of an organic coating on a metal or similarly hard substrate in terms of drawing leads or pencil leads of known hardness. 1.2 This test method is similar in content (but not technically equivalent) to ISO 15184. NOTE 1—Other procedures are available to measure permanent deformation of organic coatings under the action of a single point (stylus tip) including but not limited to Test Methods D2197, D5178, and G171. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Film Hardness by Pencil Test

ASTM D1640/D1640M-14(2022) 有机涂层干燥、固化或成膜的标准试验方法

1.1 These test methods cover the determination of the various stages and rates of film formation in the drying or curing of organic coatings under laboratory controlled conditions of air temperature, (low, ambient and/or elevated) and/or humidity. Procedures for assessing drying under prevailing conditions of temperature and humidity in the shop and field are also described. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Drying, Curing, or Film Formation of Organic Coatings

ASTM F735-22 用振动砂法测定透明塑料和涂层耐磨性的标准试验方法

1.1 This test method determines the resistance of transparent plastics and transparent coatings utilized in windows or viewing ports to surface abrasion using oscillating sand. 1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Abrasion Resistance of Transparent Plastics and Coatings Using the Oscillating Sand Method

DIN EN 13523-3:2022 卷材涂层金属 测试方法 第3部分：色差和同色异谱 仪器比较；德文版 EN 13523-3:2021

This document specifies procedures for determining the instrumental colour difference (CIELAB) of an organic coating on a metallic substrate compared to another one used as a reference (usually called reference) and the metamerism depending on the illuminant.

Coil coated metals - Test methods - Part 3: Colour difference and metamerism - Instrumental comparison; German version EN 13523-3:2021