25.220.60 标准查询与下载

ASTM F1665-08(2018) 聚氯乙烯（PVC）和其他合成有机聚合物涂层钢铁丝绳用链条栅栏的标准规范

Standard Specification for Poly(Vinyl Chloride) (PVC) and Other Conforming Organic Polymer-Coated Steel Barbed Wire Used With Chain-Link Fence

ASTM D1640/D1640M-14(2018) 有机涂层干燥、固化或成膜的标准试验方法

1.1 These test methods cover the determination of the various stages and rates of film formation in the drying or curing of organic coatings under laboratory controlled conditions of air temperature, (low, ambient and/or elevated) and/or humidity. Procedures for assessing drying under prevailing conditions of temperature and humidity in the shop and field are also described. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Drying, Curing, or Film Formation of Organic Coatings

BS EN 13523-24:2017 卷材涂层金属 测试方法 抗粘连和压力标记

Coil coated metals. Test methods. Resistance to blocking and pressure marking

EN 13523-8:2017 卷材涂层金属的试验方法.第8部分:耐盐雾性

Coil coated metals - Test methods - Part 8: Resistance to salt spray (fog)

EN 13523-21:2017 卷材覆层金属的试验方法.第21部分:户外暴露板的评价

Coil coated metals - Test methods - Part 21: Evaluation of outdoor exposed panels

ASTM D2793-99(2017) 有机涂料在木板基材上的抗阻性的标准试验方法

1.1 This test method covers the determination of the block resistance of organic coatings on wood and wood-based panel substrates. Block resistance is the ability of a coating to resist sticking to another surface and to resist any change in appearance when it is pressed against that surface for a prolonged period of time. 1.2 General methods for determining block resistance are outlined in Sections 6 and 7. Variations inherent in user materials and procedures, however, may dictate adjustments to the general method to improve accuracy. Paragraphs 7.3 and 7.4 provide guidelines for tailoring the general procedure to a user’s specific application. Paragraph 7.5 offers a rating methodology. 1.3 Test Method D2091 should be used for the determination of print resistance or pressure mottling of organic coatings, particularly lacquers, applied to wood-based case goods such as furniture. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Block Resistance of Organic Coatings on Wood Panel Substrates

EN 13523-24:2017 卷材覆层金属的试验方法.第24部分:耐粘结性和压力标记

Coil coated metals - Test methods - Part 24: Resistance to blocking and pressure marking

ASTM D6132-13(2017) 使用超声波涂层厚度测量仪对应用的有机涂层的干膜厚度进行非破坏性测量的标准测试方法

1.1 This test method describes the use of ultrasonic film thickness gages to measure accurately and nondestructively the dry film thickness of organic coatings applied over a substrate of dissimilar material. Measurements may be made on field structures, on commercially manufactured products, or on laboratory test specimens. These types of gages can accurately measure the dry film thickness of organic coatings on a variety of substrates such as concrete, wood, wallboard, plastic, fiber composites and metal. 1.2 This test method is not applicable to coatings that will be readily deformable under load of the measuring instrument as the instrument probe is placed directly on the coating surface to take a reading. 1.3 The effective range of instruments using the principle of ultrasonics is limited by gage design. A thickness range of 8 µm to 7.60 mm (0.3 to 300 mils) has been demonstrated. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Coating Thickness Gage

ASTM F735-17 透明塑料和涂料使用振荡砂法的耐磨性的标准测试方法

1.1 This test method determines the resistance of transparent plastics and transparent coatings utilized in windows or viewing ports, to surface abrasion using oscillating sand. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.2.1 Exception—The inch-pound units in parentheses are provided for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Abrasion Resistance of Transparent Plastics and Coatings Using the Oscillating Sand Method

ASTM D968-17 有机涂层耐磨性的标准试验方法

1.1 These test methods cover the determination of the resistance of organic coatings to abrasion produced by abrasive falling onto coatings applied to a plane rigid surface, such as a metal or glass panel. 1.2 Two test methods based on different abrasives are covered as follows: Sections Method A—Falling Sand Abrasion Test 6 – 13 Method B—Falling Silicon Carbide Abrasion Test 14 – 21 1.3 These methods should be restricted to testing in only one laboratory when numerical values are used because of the poor reproducibility of the methods (see 13.1.2 and 21.1.2). Interlaboratory agreement is improved significantly when ranking is used in place of numerical values. 1.4 The values stated in SI units are to be regarded as the standard with the exception of mils when determining coating thickness. The values given in parentheses are for information only. 1.5 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive

BS EN 13523-27:2017 卷材涂层金属 测试方法 耐潮湿膏剂（巴布剂测试）

Coil coated metals. Test methods. Resistance to humid poultice (Cataplasm test)

ASTM D6991-17 用悬臂（梁）法测量有机涂层内部应力的标准试验方法

Standard Test Method for Measurements of Internal Stresses in Organic Coatings by Cantilever (Beam) Method

ASTM D6991-17e1 用悬臂（梁）法测量有机涂层内部应力的标准试验方法

1.1 This test method covers the procedure for measurements of internal stresses in organic coatings by using the cantilever (beam) method. 1.2 This method is appropriate for the coatings for which the modulus of elasticity of substrate (Es) is significantly greater than the modulus of elasticity of coating (Ec) and for which the thickness of substrate is significantly greater than thickness of coating (see Note 7 and Note 8). 1.3 The stress values are limited by the adhesion values of coating to the substrate and by the tensile strength of the coating, or both. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and to determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measurements of Internal Stresses in Organic Coatings by Cantilever (Beam) Method

DIN EN 13523-29:2017 卷材镀层金属.试验方法.第29部分:环境污染耐受度(沾污性和条纹);德文版本EN 13523-29-2017

Coil coated metals - Test methods - Part 29: Resistance to environmental soiling (Dirt pick-up and striping); German version EN 13523-29:2017

DIN EN 13523-22:2017 卷材镀层金属.试验方法.第22部分:色差. 外观比对;德文版本EN 13523-22-2017

Coil coated metals - Test methods - Part 22: Colour difference - Visual comparison; German version EN 13523-22:2017

DIN EN 13523-10:2017 卷材镀层金属.试验方法.第10部分:耐荧光紫外光线和水冷凝;德文版本EN 13523-10-2017

Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation; German version EN 13523-10:2017

DIN EN 13523-12:2017 卷材镀层金属.试验方法.第12部分:耐划痕;德文版本EN 13523-12-2017

Coil coated metals - Test methods - Part 12: Resistance to scratching; German version EN 13523-12:2017

EN 13523-27:2017 卷材涂层金属-试验方法-第27部分:耐潮湿膏药(巴布剂测试)

This part of the EN 13523 series specifies a procedure for evaluating the resistance of an organic coating on a metallic substrate (coil coating) in conditions of extreme humidity (acid, alkaline and/or neutral).

Coil coated metals - Test methods - Part 27: Resistance to humid poultice (Cataplasm test)

BS EN 13523-12:2017 卷材涂层金属 测试方法 耐刮擦

Coil coated metals. Test methods. Resistance to scratching

BS EN 13523-29:2017 卷材涂层金属 测试方法 耐环境污染（沾污和条纹）

Coil coated metals. Test methods. Resistance to environmental soiling (Dirt pick-up and striping)