27.060.10 液体和固体燃料燃烧器 标准查询与下载

KS B 8008-2020 用于燃油设备的加注泵

Filler pumps for oil burning appliances

KS B 8023-2020 燃油器具供油铜管

Oil supply copper pipe for oil burning appliances

KS B 6202-2020 铸铁锅炉的建造

Construction of cast iron boilers

KS B 8010-2020 燃油器具油控制器

Oil controler for oil burning appliances

KS B 8021-2020 燃油电器试验方法一般规则

General rules for test methods of oil burning appliances

KS B 8901-2020 木屑颗粒锅炉

Wood pellet boilers

ASTM D6469-20 燃料和燃料系统微生物污染标准指南

1.1 This guide provides personnel who have a limited microbiological background with an understanding of the symptoms, occurrence, and consequences of chronic microbial contamination. The guide also suggests means for detection and control of microbial contamination in fuels and fuel systems. This guide applies primarily to gasoline, aviation, boiler, industrial gas turbine, diesel, marine, furnace fuels and blend stocks (see Specifications D396, D910, D975, D1655, D2069, D2880, D3699, D4814, D6227, and D6751), and fuel systems. However, the principles discussed herein also apply generally to crude oil and all liquid petroleum fuels. ASTM Manual 472 provides a more detailed treatment of the concepts introduced in this guide; it also provides a compilation of all of the standards referenced herein that are not found in the Annual Book of ASTM Standards, Section Five on Petroleum Products and Lubricants. 1.2 This guide is not a compilation of all of the concepts and terminology used by microbiologists, but it does provide a general understanding of microbial fuel contamination. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Microbial Contamination in Fuels and Fuel Systems

T/LJH 020-2020 智能型太阳能-生物质节能环保多功能炉

本标准规定了智能型太阳能-生物质节能环保多功能炉产品的范围、规范性引用文件、术语、型号命名、技术要求、检测方法、检验规则、标识、包装、警示标识、贮存和使用。

Intelligent solar energy -biomass energy saving and environmental protection multi-functional furnace

ASTM D6423-20a 用于测定变性燃料乙醇和乙醇燃料混合物的pHe的标准测试方法

1.1 This test method covers a procedure to determine a measure of the hydrogen ion activity of high ethanol content fuels. These include denatured fuel ethanol and ethanol fuel blends. The test method is applicable to denatured fuel ethanol and ethanol fuel blends containing ethanol at 51 % by volume, or more. 1.2 Hydrogen ion activity as measured in this test method is defined as pHe. A pHe value for alcohol solutions is not comparable to pH values of water solutions. 1.2.1 The value of pHe measured will depend somewhat on the fuel blend, the stirring rate, and the time the electrode is in the fuel. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3.1 Hydrogen ion activity in water is expressed as pH and hydrogen ion activity in ethanol is expressed as pHe. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of pHe of Denatured Fuel Ethanol and Ethanol Fuel Blends

ASTM D6550-20 超临界流体色谱法测定汽油烯烃含量的标准试验方法

1.1 This test method covers the determination of the total amount of olefins in blended motor gasolines and gasoline blending stocks by supercritical-fluid chromatography (SFC). Results are expressed in terms of mass percent olefins. The method working range is from expected concentration of 1 % by mass to expected concentration of 25 % by mass total olefins. 1.2 This test method can be used for analysis of commercial gasolines, including those containing varying levels of oxygenates, such as methyl tert/butyl ether (MTBE), diisopropyl ether (DIPE), methyl tert/amyl ether (TAME), and ethanol, without interference. NOTE 1—This test method has not been designed for the determination of the total amounts of saturates, aromatics, and oxygenates. 1.3 This test method includes a relative bias section based on Practice D6708 accuracy assessment between Test Method D6550 mass percent and Test Method D1319 volume percent for total olefins in spark-ignition engine fuels as a possible Test Method D6550 alternative to Test Method D1319 for U.S. EPA regulations reporting. The Practice D6708 derived correlation equation is only applicable for test result range from 0.53 % to 26.88 % by mass as reported by Test Method D6550. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Olefin Content of Gasolines by Supercritical-Fluid Chromatography

ASTM D6423-20 用于测定变性燃料乙醇和乙醇燃料混合物的pHe的标准测试方法

Standard Test Method for Determination of pHe of Denatured Fuel Ethanol and Ethanol Fuel Blends

ASTM D6421-20 用台架法评定汽车火花点火式发动机电子端口喷油器污染用燃料的标准试验方法

1.1 This test method covers a bench test procedure to evaluate the tendency of automotive spark-ignition engine fuel to foul electronic port fuel injectors (PFI). The test method utilizes a bench apparatus equipped with Bosch injectors specified for use in a 1985-1987 Chrysler 2.2 L turbocharged engine. This test method is based on a test procedure developed by the Coordinating Research Council (CRC) for prediction of the tendency of spark-ignition engine fuel to form deposits in the small metering clearances of injectors in a port fuel injection engine (see CRC Report No. 592).2 1.2 The test method is applicable to spark-ignition engine fuels, which may contain antioxidants, corrosion inhibitors, metal deactivators, dyes, deposit control additives, demulsifiers, or oxygenates, or a combination thereof. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given throughout this test method. NOTE 1—If there is any doubt as to the latest edition of Test Method D6421, contact ASTM International Headquarters. Other properties of significance to spark-ignition engine fuel are described in Specification D4814. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Evaluating Automotive Spark-Ignition Engine Fuel for Electronic Port Fuel Injector Fouling by Bench Procedure

BS EN 267:2020 用于液体燃料的强制通风燃烧器

What is BS EN 267 about?   BS EN 267 specifies the terminology, the general requirements for the construction and operation of forced draught oil burners and also the provision of control and safety devices, and the test procedure for these burners.   BS EN 267 specifies the requirements to ensure safety during commissioning, start-up,   operation, shutdown, and maintenance.   BS EN 267 applies to forced draught oil burners supplied with fuel based on first raffinates and their mixtures with biogenous liquid fuels having a viscosity at the burner inlet of 1,6 mm2/s (cSt) up to 6 mm2/s (cSt) at 20 °C, and higher boiling petroleum-based first raffinates (viscosity greater than 6 mm2/s), that require preheating for proper atomization.   BS EN 267 deals with all significant machine hazards, hazardous situations and events relevant to burners, when they are used as intended and under conditions of misuse which are reasonably foreseeable.  

Forced draught burners for liquid fuels

KS B 8022-2019 开放式送风燃油小型取暖器NOx排放率测定方法

Measurement method of NOx emission rate for open type forced draught oil burning space heaters

KS B 6221-2019 枪式轻油燃烧器

Gun type light oil burners

KS B 6205-2019 陆地锅炉 热平衡

Land boilers — Heat balancing

ASTM D5986-96(2019) 测定含氧化合物、苯、甲苯、C8&x2013的标准试验方法；气相色谱/傅里叶变换红外光谱法测定成品汽油中的芳烃和总芳烃

1.1 This test method covers the quantitative determination of oxygenates: methyl-t-butylether (MTBE), di-isopropyl ether (DIPE), ethyl-t-butylether (ETBE), t-amylmethyl ether (TAME), methanol (MeOH), ethanol (EtOH), 2-propanol (2PrOH), t-butanol (t-BuOH), 1-propanol (1-PrOH), 2-butanol (2-BuOH), i-butanol (i-BuOH), 1-butanol (1-BuOH); benzene, toluene and C8–C12 aromatics, and total aromatics in finished motor gasoline by gas chromatography/Fourier Transform infrared spectroscopy (GC/FTIR). 1.2 This test method covers the following concentration ranges: 0.1 % to 20 % by volume per component for ethers and alcohols; 0.1 % to 2 % by volume benzene; 1 % to 15 % by volume for toluene, 10 % to 40 % by volume total (C6–C12) aromatics. 1.3 The method has not been tested by ASTM for refinery individual hydrocarbon process streams, such as reformates, fluid catalytic cracking naphthas, etc., used in blending of gasolines. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Oxygenates, Benzene, Toluene, C8–C12 Aromatics and Total Aromatics in Finished Gasoline by Gas Chromatography/Fourier Transform

ASTM D6615-15a(2019) 喷气式B型宽切口航空涡轮燃料标准规范

Standard Specification for Jet B Wide-Cut Aviation Turbine Fuel

ASTM D6421-19 用台架法评定汽车火花点火式发动机电子端口喷油器污染用燃料的标准试验方法

Standard Test Method for Evaluating Automotive Spark-Ignition Engine Fuel for Electronic Port Fuel Injector Fouling by Bench Procedure

BS 5410-1:2019 液体燃料燃烧操作规程 住宅建筑供暖和热水供应装置

What is this standard about? This standard is the first in a three-part series on handling liquid fuels. This part gives best practice recommendations on dealing with space heating and hot water supply installations in people’s homes. Who is this standard for? Designers Specifiers Installers Service and commissioning engineers Building owners and plant manager using or intending to use liquid fuels/oil fired equipment Health and safety, and building inspectors Why should you use this standard? It gives recommendations and guidance on the design, installation, commissioning and maintenance of liquid fuel burning installations for space heating and hot water supply purposes in domestic buildings. It also gives recommendations and guidance on the selection and installation of liquid fuel storage tanks of capacity up to 3,500 litres, when installed at domestic buildings. The standard also applies to liquid fuel fired cookers where these are connected to flues and to installations burning liquid fuel conforming to BS 2869 , including biofuels conforming to BS EN 14214 and blends thereof.   NOTE: This part of BS 5410 doesn’t apply to liquid fuel fired systems for marine and transportable installations, or for flueless heaters (e.g. gel fires covered by

Code of practice for liquid fuel firing. Installations for space heating and hot water supply purposes for domestic buildings