27.070 燃料电池 标准查询与下载
共找到 399 条与 燃料电池 相关的标准，共 27 页
本文件规定了质子交换膜燃料电池涂层金属极板测试的术语和定义、缺陷测试、接触电阻测试、涂层结合力测试、涂层成分与厚度测试、耐蚀性测试、铁离子含量测试、残余应力测试。
Test method for proton exchange membrane fuel cell coating metal bipolar plate
- ICS
- 27.070
- CCS
- C384
- 发布
- 2023-07-07
- 实施
- 2023-08-01
样品要求 引射器应经过出厂/下线测试合格后方能进行性能试验。 引射器应无明显划伤、变形等缺陷；铭牌、标志安装端正牢固，字迹清晰。零部件紧固可靠，无锈蚀、毛刺、裂纹等缺陷和损伤，目视无明显外观损伤及杂质。 试验环境 试验区域环境温度：5℃～45℃。 试验涉氢区域应符合GB/T 29729-2022中相关规定。
Performance test methods of ejector for fuel cell system
- ICS
- 27.070
- CCS
- M731
- 发布
- 2023-07-06
- 实施
- 2023-07-06
1、范围 2、规范性引用文件 3、术语和定义 4、安装场地要求 5、设备安装 6、设备检查 7、环保要求 8、维护测试 9、文件
Hydrogen fuel cell power systems-Installation
- ICS
- 27.070
- CCS
- C359
- 发布
- 2023-06-29
- 实施
- 2023-06-29
本文件规定了质子交换膜燃料电池冷却液(以下简称冷却液)的术语和定义、产品分类、技术要求和试验方法、检验规则、以及标志、包装、运输和贮存等要求。
Proton exchange membrane fuel cell coolant
- ICS
- 27.070
- CCS
- C3670
- 发布
- 2023-06-08
- 实施
- 2023-07-01
Fuel cell technologies - Part 8-301: Energy storage systems using fuel cell modules in reverse mode - Power-to-methane energy systems based on solid oxide cells including reversible operation - Performance test methods
- ICS
- 27.070
- CCS
- 发布
- 2023-05-23
- 实施
本文件规定了燃料电池用低电导率冷却液的技术要求、试验方法和检验规则。 本文件适用于采用液体冷却的质子交换膜燃料电池及发电系统，其材质限定于铝镁合金、铜系金属、不锈钢、钛材、钎焊片等有限适应金属及非金属材料。 注1：本文件不适用于需要加装特定滤除离子循环设备的质子交换膜燃料电池及发电系统。 注2：直冷式锂电池等需要较低导电介质的热利用循环系统可参考本文件使用。
Technical requirements of low-conductivity coolant for fuel cell
- ICS
- 27.070
- CCS
- C384
- 发布
- 2023-03-27
- 实施
- 2023-03-27
Fuel cell technologies — Part 6-400: Micro fuel cell power systems — Power and data interchangeability
- ICS
- 27.070
- CCS
- 发布
- 2023-03-14
- 实施
Fuel cell technologies — Part 8-102: Energy storage systems using fuel cell modules in reverse mode — Test procedures for the performance of single cells and stacks with proton exchange membranes, inc
- ICS
- 27.070
- CCS
- 发布
- 2023-03-14
- 实施
Fuel cell technologies — Part 4-102: Fuel cell power systems for industrial electric trucks — Performance test methods
- ICS
- 27.070
- CCS
- 发布
- 2023-03-14
- 实施
本文件规定了质子交换膜燃料电池石墨双极板特性测试方法的术语和定义、双极板密度测试、双极板抗弯强度测试、双极板抗压强度测试、双极板接触角测试、双极板气密性测试、双极板腐蚀电流密度测试、双极板面内电导率测试、双极板接触电阻率测试、双极板导热系数测试、双极板线性热膨胀系数测试、双极板热耐久性测试、双极板电化学耐久性测试等。 本文件适用于质子交换膜燃料电池用石墨双极板。
Test standard of graphite bipolar plate characteristics for proton exchange membrane fuel cell
- ICS
- 27.070
- CCS
- C309
- 发布
- 2023-03-13
- 实施
- 2023-03-14
BS EN IEC 62282-3-201. Fuel cell technologies - Part 3-201. Stationary fuel cell power systems. Performance test methods for small fuel cell power systems
- ICS
- 27.070
- CCS
- 发布
- 2023-03-01
- 实施
- 2023-03-01
BS EN IEC 62282-3-200. Fuel cell technologies - Part 3-200. Stationary fuel cell power systems. Performance test methods
- ICS
- 27.070
- CCS
- 发布
- 2023-02-28
- 实施
- 2023-02-28
1 Scope This part of IEC 62282 specifies the performance test methods of fuel cell power systems for propulsion and auxiliary power units (APU). This document covers fuel cell power systems for propulsion other than those for road vehicles. This document covers the performance test methods of fuel cell power systems intended to be used for electrically powered industrial trucks as defined in ISO 5053‑1, except for: — rough-terrain trucks; — non-stacking low-lift straddle carrier; — stacking high-lift straddle carrier; — rough-terrain variable-reach truck; — slewing rough-terrain variable-reach truck; — variable-reach container handler; — pedestrian propelled trucks. This document applies to gaseous hydrogen-fuelled fuel cell power systems and direct methanol fuel cell power systems for electrically powered industrial trucks. The following fuels are considered within the scope of this document:
Fuel cell technologies. Fuel cell power systems for electrically powered industrial trucks. Performance test methods
- ICS
- 27.070
- CCS
- 发布
- 2023-02-28
- 实施
- 2023-02-28
IEC 62282-4-102:2022 is available as IEC 62282-4-102:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62282-4-102:2022 specifies the performance test methods of fuel cell power systems for propulsion and auxiliary power units (APU). This document covers fuel cell power systems for propulsion other than those for road vehicles. This document applies to gaseous hydrogen-fuelled fuel cell power systems and direct methanol fuel cell power systems for electrically powered industrial trucks. The following fuels are considered within the scope of this document: - gaseous hydrogen, and - methanol. This document covers the fuel cell power system as defined in 3.7 and Figure 1. This document applies to DC type fuel cell power systems, with a rated output voltage not exceeding DC 150 V for indoor and outdoor use. This document covers fuel cell power systems whose fuel source container is permanently attached to either the industrial truck or the fuel cell power system. This second edition cancels and replaces the first edition published in 2017. This edition includes the following significant technical changes with respect to the previous edition: a. alignment of the Scope with the second edition of IEC 62282-4-101:2022; b. deletion of terms and definitions (previous entries 3.5, 3.10, and 3.15); c. addition of new terms in Clause 3: "delivered power" (3.13) and "regenerated power" (3.14); d. revision of symbols and their meanings in alignment with those of IEC 62282-3-201; e. replacement of "reference conditions" with "standard conditions" as seen in Clause 5; f. revision of the test method for the accessory load voltage spike test (13.3.2); g. addition of clarifications in Clause 14 (Power stability under operation); h. addition of a checklist for performance criteria dealt with in this document (Annex C).
Fuel cell technologies - Part 4-102: Fuel cell power systems for electrically powered industrial trucks - Performance test methods
- ICS
- 27.070
- CCS
- 发布
- 2023-02-03
- 实施
- 2023-04-24 (7)
中国电工技术学会团体标准T/CES 176-2022《固定式质子交换膜燃料电池堆使用寿命测试评价方法》由中国电工技术学会提出，武汉理工大学等单位起草编制完成。该标准规范了固定式质子交换膜燃料电池堆的测试条件和测试平台，对燃料电池堆运行模拟测试方法、测试步骤、运行工况图谱、仪器设备和使用寿命范围评价等内容方面做出了技术要求，为验证质子交换膜燃料电池堆使用寿命评价方法的有效性提供了标准指导，填补固定式质子交换膜燃料电池堆性能测试评价领域标准的空白。
Evaluation method for lifetime of stationary proton exchange membrane fuel cell stack
- ICS
- 27.070
- CCS
- D4420
- 发布
- 2022-12-19
- 实施
- 2023-03-29
本文件规定了户外便携式储能电源设备的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。
Outdoor portable energy storage power supply equipment
- ICS
- 27.070
- CCS
- C384
- 发布
- 2022-12-12
- 实施
- 2022-12-13
本文件规定了固态储能系统的术语和定义、要求、试验方法、检验规则、标志、包装、运输和贮存技术要求。
Technical requirements for solid state energy storage system
- ICS
- 27.070
- CCS
- D4420
- 发布
- 2022-12-12
- 实施
- 2022-12-13
1 Scope This document deals with safety of fuel cell power systems for propulsion other than road vehicles and auxiliary power units (APU). This part of IEC 62282 covers safety requirements for fuel cell power systems intended to be used in electrically powered industrial trucks as defined in ISO 5053‑1, except for: — rough-terrain trucks; — non-stacking low-lift straddle carriers; — stacking high-lift straddle carriers; — rough-terrain variable-reach trucks; — slewing rough-terrain variable-reach trucks; — variable-reach container handlers; — pedestrian propelled trucks. This document applies to gaseous hydrogen-fuelled fuel cell power systems and direct methanol fuel cell power systems for electrically powered industrial trucks. The following fuels are considered within the scope of this document: — gaseo...
Fuel cell technologies - Fuel cell power systems for electrically powered industrial trucks. Safety
- ICS
- 27.070
- CCS
- 发布
- 2022-11-30
- 实施
- 2022-11-30
本文件适用于以氢气为燃料的城市轨道交通车辆用燃料电池发电系统，其它轨道交通车辆用燃料电池发电系统可参照执行。本文件重点关注是: -系统的安全性; -对环境条件的描述; -确保燃料电池动力系统符合铁路应用的所有要求的规范和说明; -标记和标签要求; -有关储存、运输、安装和维护的要求; -验证燃料电池动力系统所需的测试
Fuel cell power system for urban rail transit vehicles
- ICS
- 27.070
- CCS
- C384
- 发布
- 2022-11-11
- 实施
- 2022-12-12
首先明确标准的适用范围：本标准规定了沿海地区燃料电池发动机系统盐雾腐蚀测试的试验流程、试验设备、试验溶液、盐雾试验前测试、盐雾试验预处理、盐雾试验方法、试验后的处理、评价方法、盐雾试验后测试和试验报告信息等内容。 本标准第3章规定了本文件中需要用到的术语和定义，共定义了燃料电池等11项术语和定义。 本标准第4章规定了沿海地区燃料电池发动机系统盐雾腐蚀测试的试验流程。 本标准第5章规定了沿海地区燃料电池发动机系统盐雾腐蚀测试的试验设备，包括盐雾箱、湿热箱、标准大气箱。 本标准第6章规定了沿海地区燃料电池发动机系统盐雾腐蚀测试的试验溶液，包括氯化钠溶液、溶液PH值、过滤等内容。 本标准第7章规定了沿海地区燃料电池发动机系统的盐雾试验前测试，包括气密测试、绝缘性测试、极化曲线测试、力矩。 本标准第8章规定了沿海地区燃料电池发动机系统的盐雾试验预处理。 本标准第9章规定了沿海地区燃料电池发动机系统的盐雾试验方法，包括通用要求、试验条件、试验原理和依据、试验方法。 本标准第10章规定了沿海地区燃料电池发动机系统试验后的处理。 本标准第11章规定了沿海地区燃料电池发动机系统盐雾腐蚀测试的评价方法，包括起泡等级评定、生锈等级评定、开裂等级评定、剥落等级评定、粉化等级评定、变色等级评定、长霉等级评定、综合评定。 本标准第12章规定了沿海地区燃料电池发动机系统的盐雾试验后测试，包括气密测试、绝缘性测试、极化曲线测试、力矩测试、数据对比。 本标准第12章规定了沿海地区燃料电池发动机系统盐雾腐蚀测试及评价的试验报告信息，包括盐雾试验条件和方法、等级评价试验。
Salt spray corrosion test and grade evaluation of fuel cell engine system in coastal area
- ICS
- 27.070
- CCS
- D441
- 发布
- 2022-11-01
- 实施
- 2022-11-03
