29.035.20 塑料和橡胶绝缘材料 标准查询与下载
共找到 1692 条与 塑料和橡胶绝缘材料 相关的标准，共 113 页
Flexible insulating sleeving — Part 3: Specifications for individual types of sleeving — Sheet 281: Heat-shrinkable, polyolefin sleeving, semiconductive
- ICS
- 29.035.20
- CCS
- 发布
- 2021-12-14
- 实施
Flexible insulating sleeving — Part 3: Specifications for individual types of sleeving — Sheet 205: Heat-shrinkable chlorinated polyolefin sleeving, flame retarded, nominal shrink ratio 1.7 : 1 and 2
- ICS
- 29.035.20
- CCS
- 发布
- 2021-12-14
- 实施
Flexible insulating sleeving — Part 3: Specifications for individual types of sleeving — Sheet 281: Heat-shrinkable, polyolefin sleeving, semiconductive
- ICS
- 29.035.20
- CCS
- 发布
- 2021-12-14
- 实施
Flexible insulating sleeving — Part 3: Specifications for individual types of sleeving — Sheet 284: Heat-shrinkable sleeving, for oil barrier applications
- ICS
- 29.035.20
- CCS
- 发布
- 2021-12-14
- 实施
Flexible insulating sleeving — Part 3: Specifications for individual types of sleeving — Sheet 284: Heat-shrinkable sleeving, for oil barrier applications
- ICS
- 29.035.20
- CCS
- 发布
- 2021-12-14
- 实施
Flexible insulating sleeving — Part 3: Specifications for individual types of sleeving — Sheet 282: Heat-shrinkable, polyolefin sleeving — Stress control
- ICS
- 29.035.20
- CCS
- 发布
- 2021-12-14
- 实施
Flexible insulating sleeving — Part 3: Specifications for individual types of sleeving — Sheet 282: Heat-shrinkable, polyolefin sleeving — Stress control
- ICS
- 29.035.20
- CCS
- 发布
- 2021-12-14
- 实施
1.1 This specification establishes requirements for insulated vinyl siding, which is vinyl siding with integral foam plastic insulating material, where the vinyl siding is manufactured from rigid PVC compound. Compliance with this standard requires insulated vinyl siding to demonstrate a thermal insulation value of R-2.0 or greater. Other performance requirements and test methods addressed by this standard include materials properties and dimensions, warp, shrinkage, impact strength, expansion, appearance, thermal distortion resistance, flame spread, and windload resistance. Methods of indicating compliance with this specification are also provided. NOTE 1—Insulated vinyl siding is composed of two major components: the vinyl siding and the insulating material. It is intended that the vinyl siding portion comply with Specification D3679. Applicable portions of Specification D3679 are included in this specification. Additional requirements that pertain only to the insulation as a separate material, or to the combination of vinyl siding and insulation as a whole, are also included. For further explanation, see Appendix X1. 1.2 Insulated vinyl siding shall be tested with the insulation material in place or removed, as specified in the applicable requirement or test method. 1.3 The use of PVC recycled plastic in this product shall be in accordance with the requirements in Section 4. 1.4 Insulated vinyl siding produced to this specification shall be installed in accordance with Practice D4756. Reference shall also be made to the manufacturer’s installation instructions for the specific product to be installed. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 2—There is no known ISO equivalent to this standard. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Specification for Insulated Vinyl Siding
- ICS
- 29.035.20
- CCS
- 发布
- 2021-12-01
- 实施
1 Scope This sheet of IEC 60674‑3 gives the requirements for biaxially oriented polypropylene film having a smooth or rough surface, corona treated when required for vacuum metallization. The films are for use as dielectric in capacitors. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application is based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. Safety warning: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner.
Plastic films for electrical purposes. Specifications for individual materials. Sheet 1. Biaxially oriented polypropylene (PP) film for capacitors
- ICS
- 29.035.20
- CCS
- 发布
- 2021-10-31
- 实施
- 2021-10-31
Selection guidelines for polymeric materials for outdoor use under HV stress
- ICS
- 29.035.20
- CCS
- K15
- 发布
- 2021-10-29
- 实施
- 2021-10-29
Plastic films for electrical purposes – Part 3: Specifications for individual materials – Sheet 1: Biaxially oriented polypropylene (PP) film for capacitors
- ICS
- 29.035.20
- CCS
- 发布
- 2021-10-08
- 实施
- 2021-10-08
Plastic films for electrical purposes - Part 3 : specifications for individual materials - Sheet 1 : biaxially oriented polypropylene (PP) film for capacitors
- ICS
- 29.035.20
- CCS
- K15
- 发布
- 2021-10-01
- 实施
- 2021-11-20
1.1 This test method covers the determination of the energy required to rupture standard tension-impact specimens of plastic materials. Rigid materials are suitable for testing by this method as well as specimens that are too flexible or thin to be tested in accordance with other impact test methods. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. NOTE 1—This test method and ISO 8256 address the same subject matter, but differ in technical content. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Method for Determining the Tensile-Impact Resistance of Plastics
- ICS
- 29.035.20
- CCS
- 发布
- 2021-10-01
- 实施
IEC 60674-3-1:2021 is available as IEC 60674-3-1:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 60674-3-1:2021 gives the requirements for biaxially oriented polypropylene film having a smooth or rough surface, corona treated when required for vacuum metallization. The films are for use as dielectric in capacitors. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application is based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. Safety warning: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner. This second edition cancels and replaces the first edition published in 1998 and Amendment 1:2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - this document has been completely revised editorially and technically and included in the IEC 60674 series of standards; - the test methods have been updated to reflect today’s state of the art.
Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: Biaxially oriented polypropylene (PP) film for capacitors
- ICS
- 29.035.20
- CCS
- 发布
- 2021-10-01
- 实施
- 2021-12-29 (7)
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 281: Heat-shrinkable, polyolefin sleeving, semiconductive (IEC 15/946/CDV) (english version)
- ICS
- 29.035.20
- CCS
- 发布
- 2021-09-15
- 实施
- 2021-09-15
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 282: Heat-shrinkable, polyolefin sleeving - Stress control (IEC 15/947/CDV) (english version)
- ICS
- 29.035.20
- CCS
- 发布
- 2021-09-15
- 实施
- 2021-09-15
Selection guidelines for polymeric materials for outdoor use under HV stress
- ICS
- 29.035.20
- CCS
- 发布
- 2021-09-09
- 实施
- 2021-09-09
Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: Biaxially oriented polypropylene (PP) film for capacitors
- ICS
- 29.035.20
- CCS
- 发布
- 2021-08-25
- 实施
Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: Biaxially oriented polypropylene (PP) film for capacitors
- ICS
- 29.035.20
- CCS
- 发布
- 2021-08-25
- 实施
1.1 In general, the physical and electrical properties of plastics are influenced by temperature and relative humidity in a manner that materially affects test results. In order to make reliable comparisons between different materials and between different laboratories, it is necessary to standardize the humidity conditions, as well as the temperature, to which specimens of these materials are subjected prior to and during testing. This practice defines procedures for conditioning plastics (although not necessarily to equilibrium) prior to testing, and the conditions under which they shall be tested. 1.2 For some materials, it is possible that a material specification exists that requires the use of this practice, but with some procedural modifications. The material specification takes precedence over this practice. Refer to the material specification before using this practice. Table 1 in Classification D4000 lists the ASTM material specifications that currently exist. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—This standard and ISO 291 address the same subject matter, but differ in technical content. ISO 291 describes only two temperature and humidity conditions for conditioning or testing, or both. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Practice for Conditioning Plastics for Testing
- ICS
- 29.035.20
- CCS
- 发布
- 2021-07-15
- 实施
