29.080.20 套管 标准查询与下载

T/WJGY 007-2021 高密度聚乙烯（HDPE）电缆导管

外观、尺寸、落锤冲击试验、扁平试验、环刚度、复原率、拉伸屈服强度、断裂伸长率、纵向回缩率、氧化诱导时间(200℃）

High Density Polyethylene (HDPE) Cable Conduit

DS/EN 50336:2021 不超过 36 kV 的变压器和电抗器电缆箱用套管

Bushings for transformers and reactor cable boxes not exceeding 36 kV

NF C52-036*NF EN 50336:2021 不超过 36 kV 的变压器和电抗器电缆箱用套管

Bushings for transformers and reactor cable boxes not exceeding 36 kV

T/CSEE 0221-2021 胶浸纤维绝缘套管技术规范

本文件规定了胶浸纤维绝缘套管的运行条件、结构形式、技术要求、试验项目、试验要求及检验 规则。 本文件适用于设备最高电压为（1～550）kV、频率为 50 Hz 的三相交流系统中的变压器、开关、 电抗器、箱式变压器等电力设备中使用的胶浸纤维绝缘套管（以下简称“套管”）。 经供需双方协议，本文件的部分或全部适用于下列套管： ——最高电压高于 550 kV 或非三相交流系统用套管； ——高压直流系统用套管； ——试验变压器用套管； ——电容器用套管。 本文件中对变压器套管的特殊要求和试验也适用于电抗器套管。 本文件适用于单独制作和销售的套管。构成电气设备的一部分且不能按本文件试验的套管，应随 该电气设备一起试验。

Technical specifications for rubber-impregnated fiber insulation bushings

KS C IEC 60437-2020 高压绝缘子无线电干扰测试

Radio interference test on high-voltage insulators

KS C IEC 60437:2020 高压绝缘子无线电干扰测试

Radio interference test on high-voltage insulators

KS C IEC 60137:2020 绝缘衬套 交流电压高于1000 V

Insulated bushings for alternating voltages above 1 000 V

KS C IEC 60137-2020 绝缘衬套 交流电压高于1000 V

Insulated bushings for alternating voltages above 1 000 V

KS C IEC 62199-2019 直流应用套管

Bushings for d.c. application

T/CEC 243-2019 10（6）kV～35kV挤包绝缘电力电缆系统超低频（0.1Hz）现场试验方法

本标准规定了额定电压10（6）kV～35kV挤包绝缘电力电缆系统超低频（0.1Hz）现场试验的试验要求、试验方法、处理建议等。 本标准适用于额定电压10（6）kV～35kV挤包绝缘电力电缆系统超低频（0.1Hz）现场试验，包括超低频电压下的耐压试验和介质损耗因数测量。该方法可作为电力电缆及电缆附件绝缘状态评价的试验方法之一。

10 (6) kV~35kV extruded insulation power cable system ultra-low frequency (0.1Hz) field test method

ASTM F14-80(2019) 标准玻璃金属珠密封的制造和试验的标准实施规程

1.1 This practice covers procedures for preparing and testing reference glass-to-metal bead-seals for determining the magnitude of thermal expansion (or contraction) mismatch between the glass and metal. Tests are in accordance with Test Method F218 (see Section 2). 1.2 This practice applies to all glass-metal combinations, established or experimental, particularly those intended for electronic components. 1.3 The practical limit of the test in devising mismatch is approximately 300 ppm, above which the glass is likely to fracture. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Making and Testing Reference Glass-Metal Bead-Seal

BS EN 50673:2019 用于电气设备的 72.5 kV、630 A 和 1 250 A 插入式套管

What is BS EN 50673- Plug-in type bushings about?    BS EN 50673 is a European standard that discusses plug-in type bushings.   BS EN 50673 specify dimensions, properties, requirements, and tests to ensure interchangeability between plug-in type bushings and separable connectors installed high voltage power cables with extruded insulation and connected to electrical equipment, like liquid-filled transformers and gas-insulated switchgear and control gear.   Compliance with BS EN 50673 can ensure adequate mounting and interchangeability of mating plug-in separable connectors of equivalent ratings.

Plug-in type bushings for 72,5 kV with 630 A and 1 250 A for electrical equipment

DIN EN 60137 Berichtigung 1:2018 用于 1000 V 以上交流电压的绝缘套管（IEC 60137:2017/COR1:2018）；德文版 EN 60137:2017/AC:2018-08

This standard specifies the characteristics and tests for insulated bushing. This standard is applicable to bushings intended for use in electrical apparatus, machinery, transformers, switchgear and installations for three-phase alternating current systems, having highest voltage for equipment above 1000 V and power frequencies of 15 Hz up to and including 60 Hz.

Insulated bushings for alternating voltages above 1 000 V (IEC 60137:2017/COR1:2018); German version EN 60137:2017/AC:2018-08

BS EN 60137:2017 适用于 1000 V 以上交流电压的绝缘套管

What is BS EN 60137 - Insulated bushings about?   BS EN 60137 is a standard that specifies the characteristics and tests for insulated bushings.   BS EN 60137 is applicable to bushings, as defined in Clause 3, intended for use in electrical apparatus, machinery, transformers, switchgear, and installations for three-phase alternating   current systems, having the highest voltage for equipment above 1 000 V and power frequencies of 15 Hz up to and including 60 Hz.   BS EN 60137 may be applied, in part or as a whole, to the following:  

Insulated bushings for alternating voltages above 1000 V

DIN EN 60137:2018 1000 V以上交流电压用绝缘套管(IEC 60137-2017); 德文版本EN 60137-2017

This standard specifies the characteristics and tests for insulated bushing. This standard is applicable to bushings intended for use in electrical apparatus, machinery, transformers, switchgear and installations for three-phase alternating current systems, having highest voltage for equipment above 1000 V and power frequencies of 15 Hz up to and including 60 Hz.

Insulated bushings for alternating voltages above 1 000 V (IEC 60137:2017); German version EN 60137:2017

BS EN 50180-3:2015+A1:2017 kV 以上至 52 kV 以及 250 A 至 3.15 kA 的液体变压器套管 套管固定要求

What is BS EN 50180-3- Bushing fixations about?   BS EN 50180 is a European standard that discusses bushings above 1 kV up to 52 kV and from 250 A to 3,15 kA for liquid-filled transformers.    BS EN 50180-3 is the third part of the multi-series that discusses requirements for bushing fixations. BS EN 50180-3 was extended for fastenings of bushings for a highest voltage of 52 kV. This information is of importance for utilities concerning compatibility.   It should be considered in factual context with EN 50180 ‑ 1

Bushings above 1 kV up to 52 kV and from 250 A to 3,15 kA for liquid filled transformers - Requirements for bushing fixations

EN IEC/IEEE 65700:2018 直流应用套管

Bushings for DC application

NF C66-550*NF EN 60137:2017 交流电压大于1000V的绝热轴衬

La présente Norme internationale spécifie les caractéristiques et les essais applicables aux traversées isolées.

Insulated bushings for alternating voltages above 1 000 V

EN 60137:2017 用于 1000 V 以上交流电压的绝缘套管

NEW! IEC 60137:2017 is available as IEC 60137:2017 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60137:2017 specifies the characteristics and tests for insulated bushings. This standard is applicable to bushings, as defined in Clause 3, intended for use in electrical apparatus, machinery, transformers, switchgear and installations for three-phase alternating current systems, having highest voltage for equipment above 1 000 V and power frequencies of 15 Hz up to and including 60 Hz. Subject to special agreement between purchaser and supplier, this standard may be applied, in part or as a whole, to the following: - bushings used in other than three-phase systems; - bushings for high-voltage direct current systems; - bushings for testing transformers; - bushings for capacitors. Special requirements and tests for transformer bushings in this standard apply also to reactor bushings. This standard is applicable to bushings made and sold separately. Bushings which are a part of an apparatus and which cannot be tested according to this standard should be tested with the apparatus of which they form part. This edition includes the following significant technical changes with respect to the previous edition: - Resin-impregnated synthetic (RIS) bushings has been introduced. - Bushings with Um ≤ 1,1 kV, Um = 1100 kV and Um = 1200 kV have been introduced. - Temperature rise testing has been included for liquid-insulated bushings according to clause to 3.4. - Introducing dry lightning impulse testing as a routine test for all transformer bushings with Um > 72,5 kV. - The altitude correction procedure has been revised ( > 1 000 m). - An explanation about Very Fast Transient (VFT) phenomenon and its impact on bushings has been included.

Insulated bushings for alternating voltages above 1 000 V

DL/T 1726-2017 特高压直流穿墙套管技术规范

Technical specification for UHV DC wall bushing