29.080.20 套管 标准查询与下载

LST EN 50181-2010 kV 至 52 kV 和 250 A 至 2,50 kA 的插入式套管，用于液体填充变压器以外的设备

Plug-in type bushings above 1 kV up to 52 kV and from 250 A to 2,50 kA for equipment other than liquid filled transformers

BS EN 50181:2010 不包括液体填充变压器在内的设备用电压大于1 kV到52 kV范围的和电流从250 A到250 kA范围的插入型套管

This European Standard is applicable to insulated bushings for maximum voltages above 1 kV up to 52 kV, rated currents from 250 A up to 2 500 A and frequencies from 15 Hz up to 60 Hz for equipment other than liquid filled transformers. This European Standard establishes essential dimensions, to ensure adequate mounting and interchangeability of mating plug-in separable connectors of equivalent ratings.

Plug-in type bushings above 1 kV up to 52 kV and from 250 A to 2,50 kA for equipment other than liquid filled transformers

DS/EN 50181:2010 kV 至 52 kV 和 250 A 至 2,50 kA 的插入式套管，用于液体填充变压器以外的设备

This European Standard is applicable to insulated bushings for maximum voltages above 1 kV up to 52 kV, rated currents from 250 A up to 2 500 A and frequencies from 15 Hz up to 60 Hz for equipment other than liquid filled transformers.This European Standard establishes essential dimensions, to ensure adequate mounting and interchangeability of mating plug-in separable connectors of equivalent ratings.

Plug-in type bushings above 1 kV up to 52 kV and from 250 A to 2,50 kA for equipment other than liquid filled transformers

SANS 60137:2010 交流电压1000V以上的绝缘套管

Applicable to bushings intended for use in electrical apparatus, machinery, transformers, switchgear and installations for three-phase alternating current systems, having highest voltage for equipment above 1 000 V and power frequencies of 15 Hz up to an

Insulated bushings for alternating voltages above 1 000 V

ANSI/IEEE C37.017:2010 高压(超过1000 V交流电)电路断路器和气体绝缘开关设备用套管标准

This standard is applicable to bushings intended for use in high voltage circuit breakers and gas insulated switchgear. These bushings are intended for indoor and outdoor use, operating on alternating current with a rated voltage greater than 1000 V and a frequency of 50 or 60 Hz. These bushings are usually a part of an apparatus and tested according to the apparatus of which they form part. It defines the special terms used, service conditions, ratings, general requirements, test procedure and acceptance criteria for these bushings.

Standard for Bushings for High Voltage (Over 1000 Volts AC) Circuit Breakers and Gas Insulated Switchgear

DIN EN 60137:2009 1000 V以上交流电压用绝缘套管(IEC 60137-2008).德文版本EN 60137-2008

Insulated bushings for alternating voltages above 1000 V (IEC 60137:2008); German version EN 60137:2008

BS EN 60137:2008 交流电压大于1000V的绝缘套管

This International Standard specifies the characteristics and tests for insulated bushings. This standard is applicable to bushings, as defined in Clause 3, intended for use in electrical apparatus, machinery, transformers, switchgear and installations for three-phase alternating current systems, having highest voltage for equipment above 1 000 V and power frequencies of 15 Hz up to and including 60 Hz. Subject to special agreement between purchaser and supplier, this standard may be applied, in part or as a whole, to the following: • bushings used in other than three-phase systems; • bushings for high-voltage direct current systems; • bushings for testing transformers; • bushings for capacitors. Special requirements and tests for transformer bushings in this standard apply also to reactor bushings. This standard is applicable to bushings made and sold separately. Bushings which are a part of an apparatus and which cannot be tested according to this standard should be tested with the apparatus of which they form part.

Insulated bushings for alternating voltages above 1000 V

BS EN 60137:2009 交流电压1000V以上绝缘套管

Insulated bushings for alternating voltages above 1000 V

LST EN 60137-2009 用于 1000 V 以上交流电压的绝缘套管（IEC 60137:2008）

Insulated bushings for alternating voltages above 1 000 V (IEC 60137:2008)

NF C66-550:2008 交流电压大于1000V的绝热轴衬

Insulated bushings for alternating voltages above 1 000 V.

DS/EN 60137:2008 用于 1000 V 以上交流电压的绝缘套管

This International Standard specifies the characteristics and tests for insulated bushings.This standard is applicable to bushings, as defined in Clause 3, intended for use in electrical apparatus, machinery, transformers, switchgear and installations for three-phase alternating current systems, having highest voltage for equipment above 1 000 V and power frequencies of 15 Hz up to and including 60 Hz.Subject to special agreement between purchaser and supplier, this standard may be applied, in part or as a whole, to the following:• bushings used in other than three-phase systems;• bushings for high-voltage, direct current systems;• bushings for testing tran

Insulated bushings for alternating voltages above 1 000 V

SANS 1037:2008 标准变压器套管

Covers insulated bushings for use on transformers in which the hollow insulators of the bushings provide the major insulation to voltage stresses. The bushings are designed for use with one or both ends immersed in an insulating medium (such as oil) or i

Standard transformer bushings

IEC 60137:2008 交流电压1000V以上的绝缘套管

This International Standard specifies the characteristics and tests for insulated bushings. This standard is applicable to bushings, as defined in Clause 3, intended for use in electrical apparatus, machinery, transformers, switchgear and installations for three-phase alternating current systems, having highest voltage for equipment above 1 000 V and power frequencies of 15 Hz up to and including 60 Hz. Subject to special agreement between purchaser and supplier, this standard may be applied, in part or as a whole, to the following: ~ bushings used in other than three-phase systems; ~ bushings for high-voltage direct current systems; ~ bushings for testing transformers; ~ bushings for capacitors. Special requirements and tests for transformer bushings in this standard apply also to reactor bushings. This standard is applicable to bushings made and sold separately. Bushings which are a part of an apparatus and which cannot be tested according to this standard should be tested with the apparatus of which they form part.

Insulated bushings for alternating voltages above 1000 V

AS/NZS 60137:2008 1000V以上的交流电压用绝缘套管（IEC 60137，第5.0版 （2003） MOD）

Specifies the characteristics and tests for insulated bushings for electrical equipment with a voltage above 1000 V a.c. and a nominal frequency in the range 15-60 Hz.

Insulated bushings for alternating voltages above 1000 V (IEC 60137, Ed. 5.0 (2003) MOD)

DIN 89349:2008 电缆和绝缘电线密封套用密封环

This standard applies to sealing rings which are preferably used with glands for eletrical bables and insulated wires in accordance with DIN 89280-1.

Sealing rings for glands for electrical cables and insulated wires; Text in German and English

DL/T 1058-2007 交流架空线路用复合相间间隔棒技术条件

本标准规定了标称电压为220kV及以上、频率为50Hz的紧凑型交流架空线路以及220kV以下、频率为50Hz的交流架空线路用复合相间间隔棒(以下简称相间间隔棒)技术条件的一般要求、试验方法、选择原则、检验规则、验收、包装、运输和贮存、安装。 本标准适用于220kV及以上、频率为50Hz的紧凑型交流架空线路以及220kV及以下、频率为50Hz的交流架空线路，且安装地点的海拔1000m及以下，环境温度在-40℃～+40℃之间。

Technical specification of composite Insulators spacer between phase for a.c.overhead lines

DIN CLC/TS 50458:2006 浸油变压器用52 kV～420 kV电容式穿墙套管

This Technical Specification is applicable to capacitance graded outdoor bushings with values of highest voltage for equipment (U) from 52 kV up to 420 kV and with values of rated current (I) up to 3150 A and frequencies from 15 Hz up to 60 Hz for oil immersed transformers. The major insulation of these bushings consists either of oil-impregnated or resin-impregnated paper or other suitable insulating systems. This Technical Specification establishes essential details and dimensions to ensure interchangeability and adequate mounting of the bushings.

Capacitance graded outdoor bushing 52 kV up to 420 kV for oil immersed transformers; German version CLC/TS 50458:2006

DS/CLC/TS 50458:2006 用于油浸式变压器的电容分级户外套管 52 kV 至 420 kV

This Technical Specification is applicable to capacitance graded outdoor bushings with values of highest voltage for equipment (Um) from 52 kV up to 420 kV and with values of rated current (Ir) up to 3 150 A and frequencies from 15 Hz up to 60 Hz for oil immersed transformers.The major insulation of these bushings consists either of oil-impregnated or resin-impregnated paper or other suitable insulating systems.This Technical Specification establishes essential details and dimensions to ensure interchange ability and adequate mounting of the bushings.

Capacitance graded outdoor bushing 52 kV up to 420 kV for oil immersed transformers

DL/T 1001-2006 复合绝缘高压穿墙套管技术条件

本标准规定了复合绝缘高压穿墙套管的技术要求、试验方法、检验规则以及标志、包装、运输及储存。 本标准适用于标称电压35kV及以上电压等级、频率为50Hz～60Hz的交流系统电站和变电所配电装置用的户外—户内电容式复合绝缘穿墙套管（以下简称套管）。安装地点的海拔为1000m以下，环境温度为-40℃～+40℃。

Technical specification of composite insulating high voltage outdoor-indoor bushing

DIN 89345:2006 电缆和绝缘电线用密封套的接地插入件

This standard applies to earthing inserts with glands for electrical cables and insulated wires in accordance with DIN 89280-1 preferably used for electrical installations of small vessels and of mobile and fixed offshore units.

Earthing inserts for glands for electrical cables and insulated wires