31.220.10 插头和插座装置、连接器 标准查询与下载

ASTM B1004-16(2022) 电气连接系统接触性能分类的标准实施规程

1.1 This practice provides a method of specifying performance requirements for (or reporting test results of) electrical contact and connection systems. Both conductor and connector system performance may be specified by this practice, separately or in combination. 1.2 This practice may be used for separable or permanent contacts employing metallic conducting components. 1.3 This practice is applicable to both signal and power applications. 1.4 This practice is intended to be used for specifying performance of connectors and connection systems that are marketed for general public and trade application, as for instance for use in building wiring, electronics, and vehicles. 1.5 This practice is not intended to be used to specifying the performance of connection systems for specialized applications, such as military, industrial, aircraft, power distribution, and medical apparatus. 1.6 This practice does not specify the sample preparation or test sequences required for determining contact performance. It is the responsibility of the user of this practice to determine the applied test sequence(s) appropriate for the application. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provide by the manufacturer, to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Contact Performance Classification of Electrical Connection Systems

DB44/T 2354-2022 电力用户应急电源快速接口技术标准

Technical standard for fast interface of emergency power supply for power users

IEC 60512-99-002:2022 RLV 电气和电子设备用连接器.试验和测量.第99-002部分:耐久性试验计划.试验99b:电气负载下不匹配的试验计划

Connectors for electrical and electronic equipment - Tests and measurements - Part 99-002: Endurance test schedules - Test 99b: Test schedule for unmating under electrical load

IEC 60512-99-002:2022 电气和电子设备用连接器.试验和测量.第99-002部分:耐久性试验计划.试验99b:电气负载下不匹配的试验计划

Connectors for electrical and electronic equipment - Tests and measurements - Part 99-002: Endurance test schedules - Test 99b: Test schedule for unmating under electrical load

T/CECA 65-2022 BPMP系列推入式射频同轴连接器

本文件规定了BPMP系列推入式射频同轴连接器的技术要求、试验方法和交付准备等。 本文件适用于BPMP系列推入式射频同轴连接器（以下简称射频同轴连接器）的设计、制造和验收。

BPMP series push-on radio-frequency coaxial connectors

21/30443246 DC BS EN IEC 60512-28-100 电气和电子设备连接器 测试和测量 第28-100部分 信号完整性测试频率高达 2 000 MHz 测试 28a 至 28g

BS EN IEC 60512-28-100. Connectors for electrical and electronic equipment. Tests and measurements - Part 28-100. Signal integrity tests up to 2 000 MHz. Tests 28a to 28g

T/CECA 62-2021 轨道交通用GTCM系列高可靠圆形光电混装连接器

本文件规定了轨道交通用GTCM系列高可靠圆形光电混装连接器的技术要求、试验方法和交付准备等。 本文件适用于轨道交通用GTCM系列高可靠圆形光电混装连接器（以下简称：连接器）的设计、制造和验收。

GTCM series high reliability circular optoelectronic hybrid connector for rail transit

T/CECA 63-2021 轨道交通用牵引电机圆形电连接器

本文件规定了轨道交通用牵引电机圆形电连接器（以下简称：电连接器）的技术要求、质量保证规定、交货准备和型号命名规则。 本文件适用于轨道交通用牵引电机圆形电连接器的设计、制造和验收。

Circular electrical connector of traction motor for rail transit

21/30447896 DC BS EN IEC 60352-2 无焊连接 第 2 部分 压接连接 一般要求、测试方法和实践指导

BS EN IEC 60352-2. Solderless connections - Part 2. Crimped connections. General requirements, test methods and practical guidance

OVE EN IEC 61076-2-114:2021 电气和电子设备用连接器 产品要求 第 2-114 部分：圆形连接器 带电源触头和信号触头的 M8 螺钉锁定连接器的详细规范，用于高达 100 MHz 的数据传输（（IEC 61076

Connectors for electrical and electronic equipment - Product requirements - Part 2-114: Circular connectors - Detail specification for connectors with M8 screw-locking with power contacts and signal contacts for data transmission up to 100 MHz ((IEC 61076

DIN EN IEC 61076-8-101:2021 电气和电子设备用连接器 产品要求 第 8-101 部分：电源连接器 额定电流为 40 A 的 2 极或 3 极电源加 2 极信号屏蔽和密封连接器的详细规范

This part of IEC 61076-8 describes 2P or 3P power plus 2P signal shielded and sealed connectors with plastic housing (hereinafter referred to as a connector) for electromechanical equipment, including overall dimensions, interface dimensions, technical characteristics, performanc

Connectors for electrical and electronic equipment - Product requirements - Part 8-101: Power connectors - Detail specification for 2-pole or 3-pole power plus 2-pole signal shielded and sealed connectors with plastic housing for rated current of 40 A (IE

DIN EN IEC 61076-8-102:2021 电气和电子设备用连接器 产品要求 第 8-102 部分：电源连接器 额定电流为 150 A（I

This part of IEC 61076-8 describes 2P or 3P power plus 2P signal shielded and sealed connectors with plastic housing (hereinafter referred to as a connector) for electromechanical equipment, including overall dimensions, interface dimensions, technical characteristics, performanc

Connectors for electrical and electronic equipment - Product requirements - Part 8-102: Power connectors - Detail specification for 2-pole or 3-pole power plus 2-pole signal shielded and sealed connectors with plastic housing for rated current of 150 A (I

DIN EN IEC 61076-8-100:2021 电气和电子设备用连接器 产品要求 第 8-100 部分：电源连接器 额定电流为 20 A 的 2 极或 3 极电源加 2 极信号屏蔽和密封连接器的详细规范

This part of IEC 61076-8 describes 2P or 3P power plus 2P signal shielded and sealed connectors with plastic housing (hereinafter referred to as a connector) for electromechanical equipment, including overall dimensions, interface dimensions, technical characteristics, performanc

Connectors for electrical and electronic equipment - Product requirements - Part 8-100: Power connectors - Detail specification for 2-pole or 3-pole power plus 2-pole signal shielded and sealed connectors with plastic housing for rated current of 20 A (IE

DIN EN IEC 61076-2-012:2021 电气和电子设备用连接器 产品要求 第 2-012 部分：圆形连接器 根据 IEC 61076-2-101、IEC 61076-2-109、基于 M12 连接器接口的带内部推拉锁定的连接器的详细规范，

This part of IEC 61076-2 specifies circular connectors with an inner push-pull locking mechanism of a size derived from and thus being compatible with M12 screw-locking connectors (male free connector with screw-locking according to IEC 61076-2-101, IEC 61076-2-109, IEC 61076-2-1

Connectors for electrical and electronic equipment - Product Requirements - Part 2-012: Circular connectors - Detail specification for connectors with inner push-pull locking based on M12 connector interfaces according to IEC 61076-2-101, IEC 61076-2-109,

LST EN IEC 61076-2-011:2021 电气和电子设备连接器 产品要求 第 2-011 部分：圆形连接器 B12 卡口耦合连接器的详细规范，基于符合 IEC 61076-2-101 和 IEC 61076-2-109 的配合接口（IEC 61076-2

Connectors for electrical and electronic equipment - Product requirements - Part 2-011: Circular connectors - Detail specification for B12 bayonet coupling connectors based on mating interfaces according to IEC 61076-2-101 and IEC 61076-2-109 (IEC 61076-2

IEC 63171-6:2021 电气和电子设备连接器第6部分:频率高达600MHz的电力和数据传输用2路和4路（数据/电源）屏蔽自由和固定连接器详细规范

Connectors for electrical and electronic equipment - Part 6: Detail specification for 2-way and 4-way (data/power), shielded, free and fixed connectors for power and data transmission with frequencies

LST EN IEC 61076-2-010:2021 电气和电子设备的连接器 产品要求 第 2-010 部分：圆形连接器 具有外部或内部推拉锁定机构的连接器的详细规范，基于符合 IEC 61076-2-101 的配合接口，IEC

Connectors for electrical and electronic equipment - Product requirements - Part 2-010: Circular connectors - Detail specification for connectors with outer or inner push-pull locking mechanism, based on mating interfaces according to IEC 61076-2-101, IEC

OVE EN IEC 60352-3:2021 无焊连接 第3部分：可接触绝缘位移（ID）连接 一般要求、测试方法和实用指南（（IEC 60352-3:2020）EN IEC 60352-3:2020）（德文版）

Solderless connections - Part 3: Accessible insulation displacement (ID) connections - General requirements, test methods and practical guidance ((IEC 60352-3:2020) EN IEC 60352-3:2020) (german version)

OVE EN IEC 60352-4:2021 无焊连接 第4部分：不可触及的绝缘位移（ID）连接 一般要求、测试方法和实用指南（（IEC 60352-4:2020）EN IEC 60352-4:2020）（德文版）

Solderless connections - Part 4: Non-accessible insulation displacement (ID) connections - General requirements, test methods and practical guidance ((IEC 60352-4:2020) EN IEC 60352-4:2020) (german version)

DIN EN IEC 61076-2-114:2021 电气和电子设备用连接器 产品要求 第 2-114 部分：圆形连接器 带电源触头和信号触头的 M8 连接器详细规范，用于高达 100 MHz 的数据传输（IEC 61076-

This part of IEC 61076 describes circular connectors with M8 screw locking typically used for data and power transmissions in industrial applications. These connectors consist of fixed and free connectors that are either rewireable or non-rewireable. Data transmission performance

Connectors for electrical and electronic equipment - Product requirements - Part 2-114: Circular connectors - Detail specification for connectors with M8 screw-locking with power contacts and signal contacts for data transmission up to 100 MHz (IEC 61076-