75.040 原油 标准查询与下载

ASTM D4006-22 蒸馏法测定原油中水的标准试验方法

1.1 This test method covers the determination of water in crude oil by distillation. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 7.1 and A1.1. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Water in Crude Oil by Distillation

ASTM D8150-22 蒸馏法测定原油中有机氯化物含量的标准试验方法

1.1 This test method covers the determination of organic chloride (above 1 µg/g organically-bound chlorine) in crude oils, using distillation and combustion ion chromatography. 1.2 This test method involves the distillation of crude oil test specimens to obtain a naphtha fraction prior to chloride determination. The chloride content of the naphtha fraction of the whole crude oil can thereby be obtained. See Section 6 regarding potential interferences. 1.3 The test procedure covers the determination of organic chloride in the washed naphtha fraction of crude oil by combustion ion chromatography. Other halides can be determined but are not included in the precision statement of the test method. 1.4 The values stated in SI units are to be regarded as standard. The preferred concentration units are micrograms of chloride per gram of sample. 1.4.1 Exception—The values given in parentheses are for information only. 1.5 Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Organic Chloride Content in Crude Oil by Distillation Followed by Detection Using Combustion Ion Chromatography

ASTM D4007-22 离心法测定原油中水和沉积物的标准试验方法（实验室程序）

1.1 This test method describes the laboratory determination of water and sediment in crude oils by means of the centrifuge procedure. This centrifuge method for determining water and sediment in crude oils is not entirely satisfactory. The amount of water detected is almost always lower than the actual water content. When a highly accurate value is required, the revised procedures for water by distillation, Test Method D4006 (API MPMS Chapter 10.2) (Note 1), and sediment by extraction, Test Method D473 (API MPMS Chapter 10.1), shall be used. NOTE 1—Test Method D4006 (API MPMS Chapter 10.2) has been determined to be the preferred and most accurate method for the determination of water. 1.2 The values stated in SI units are to be regarded as standard. 1.2.1 Exception—The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements appear in 7.1, 9.3, and A1.5.4. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Water and Sediment in Crude Oil by the Centrifuge Method (Laboratory Procedure)

ASTM D4929-22 测定原油中有机氯化物含量的标准试验方法

1.1 The procedures in this test method cover the determination of organic chloride (above 1 µg/g organically-bound chlorine) in crude oils, using either distillation and sodium biphenyl reduction, distillation and microcoulometry, or distillation and X-ray fluorescence (XRF) spectrometry. 1.2 The procedures in this test method involve the distillation of crude oil test specimens to obtain a naphtha fraction prior to chloride determination. The chloride content of the naphtha fraction of the whole crude oil can thereby be obtained. See Section 6 regarding potential interferences. 1.3 Procedure A covers the determination of organic chloride in the washed naphtha fraction of crude oil by sodium biphenyl reduction followed by potentiometric titration. 1.4 Procedure B covers the determination of organic chloride in the washed naphtha fraction of crude oil by oxidative combustion followed by microcoulometric titration. 1.5 Procedure C covers the determination of organic chloride in the washed naphtha fraction of crude oil by X-ray fluorescence spectrometry. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6.1 The preferred concentration units are micrograms of chloride per gram of sample, though milligrams of chloride per kilogram of sample is commonly used for Procedure C. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Organic Chloride Content in Crude Oil

ASTM D7157-22e1 测定含沥青质残留物、重质燃料油和原油内在稳定性的标准试验方法（n-庚烷相分离；光学检测）

1.1 This test method covers a procedure for quantifying the intrinsic stability of the asphaltenes in an oil by an automatic instrument using an optical device. 1.2 This test method is applicable to residual products from thermal and hydrocracking processes, to products typical of Specifications D396 Grades No. 5L, 5H, and 6, and D2880 Grades No. 3-GT and 4-GT, and to crude oils, providing these products contain 0.5 % by mass or greater concentration of asphaltenes (see Test Method D6560). 1.3 This test method quantifies asphaltene stability in terms of state of peptization of the asphaltenes (S-value), intrinsic stability of the oily medium (So) and the solvency requirements of the peptized asphaltenes (Sa). 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Intrinsic Stability of Asphaltene-Containing Residues, Heavy Fuel Oils, and Crude Oils (n-Heptane Phase Separation; Optical Detectio

ASTM D7157-22 测定含沥青质残渣、重质燃料油和原油（庚烷相分离；光学检测）固有稳定性的标准试验方法

Standard Test Method for Determination of Intrinsic Stability of Asphaltene-Containing Residues, Heavy Fuel Oils, and Crude Oils (n-Heptane Phase Separation; Optical Detectio

ASTM D4310-22 测定抑制矿物油的淤泥和腐蚀倾向的标准试验方法

Standard Test Method for Determination of Sludging and Corrosion Tendencies of Inhibited Mineral Oils

ASTM D5002-22 用数字密度分析仪测定原油密度、相对密度和API比重的标准试验方法

1.1 This test method covers the determination of the density, relative density, and API gravity of crude oils that may be handled in a normal fashion as liquids at test temperatures between 15 °C and 35 °C utilizing either manual or automated sample injection equipment. This test method applies to crude oils with high vapor pressures provided appropriate precautions are taken to prevent vapor loss during transfer of the sample to the density analyzer. 1.2 This test method was evaluated in interlaboratory study testing using crude oils in the 0.75 g ⁄mL to 0.95 g ⁄mL range. Lighter crude oil may require special handling to prevent vapor losses. 1.3 The values stated in SI units are to be regarded as standard. Other units of measurement are included in this standard. The accepted units of measurement of density are grams per millilitre and kilograms per cubic metre. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in 7.4, 7.5, and 7.6. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Density, Relative Density, and API Gravity of Crude Oils by Digital Density Analyzer

ASTM D473-22 用萃取法测定原油和燃料油中沉淀物的标准试验方法

1.1 This test method covers the determination of sediment in crude oils and fuel oils by extraction with toluene. The precision applies to a range of sediment levels from 0.01 % to 0.40 % mass, although higher levels may be determined. NOTE 1—Precision on recycled oils and crankcase oils is unknown and additional testing is required to determine that precision. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 6.1.1.6 and 7.1. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Sediment in Crude Oils and Fuel Oils by the Extraction Method

ASTM D6560-22 原油和石油产品中沥青质（庚烷不溶物）测定的标准试验方法

1.1 This test method covers a procedure for the determination of the heptane insoluble asphaltene content of gas oil, diesel fuel, residual fuel oils, lubricating oil, bitumen, and crude petroleum that has been topped to an oil temperature of 260 °C (see A1.2.1.1). 1.2 The precision is applicable to values between 0.50 % m ⁄m and 30.0 % m ⁄m. Values outside this range may still be valid but may not give the same precision values. 1.3 Oils containing additives may give erroneous results. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Asphaltenes (Heptane Insolubles) in Crude Petroleum and Petroleum Products

GSO ASTM D473:2022 用萃取法测定原油和燃料油中沉积物的标准试验方法

1.1 This test method covers the determination of sediment in crude oils and fuel oils by extraction with toluene. The precision applies to a range of sediment levels from 0.01 % to 0.40 % mass, although higher levels may be determined. NOTE 1—Precision on recycled oils and crankcase oils is unknown and additional testing is required to determine that precision. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 5.1.1.6 and 6.1. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Sediment in Crude Oils and Fuel Oils by the Extraction Method

T/CPCIF 0195-2022 原油关键性质快速测定 近红外光谱法

利用原油中不同分子含氢基团等化学键的振动或转动对近红外光吸收特性的差异，采用主成分回归、偏最小二乘法、模式识别、拓扑学等化学计量学手段建立原油光谱与原油性质间的线性或非线性模型，通过模型测定原油样品的20 ℃密度、硫含量、酸值和实沸点收率。

Rapid determination of crude oil key properties— Near infrared spectrometry

T/CIESC 0034-2022 原油性质的快速测定 低频氢谱核磁共振波谱法

本文件规定了低频氢谱核磁共振波谱仪快速测定原油性质的方法。 本文件适用于80 ℃状态下呈均匀流体的原油样品。 本文件适用于符合GB/T 36170定义的原油。 本文件适用于校正模型样品性质范围内的原油性质分析。 本文件适用于水含量质量分数低于5 %的原油。 本文件适用于原油下列性质快速分析（见表1）。

Rapid determination for properties of crude oils by low resolution nuclear magnetic resonance hydrogen spectroscopy

T/GRM 049-2022 原油中总汞的分析测试方法

1  原理与方法； 2  试剂和材料； 3  仪器设备； 4  取样； 5  样品处理； 6  汞含量测定； 7  计算； 8  精密度； 9  试验报告。

Determination of Mercury in Crude Oil

KS M 2027-2021 石油产品硫含量的试验方法

Crude oil and petroleum products — Test methods of sulfur content

ASTM D7059-21 多维气相色谱法测定原油中甲醇的标准试验方法

1.1 This test method covers the determination of methanol in crude oils by direct injection multidimensional gas chromatography in the concentration range of 15 ppm (m/m) to 900 ppm (m/m). The pooled limit of quantification (PLOQ) is 15 ppm (m/m). 1.2 This test method is applicable only to crude oils containing less than or equal to 0.1 % (v/v) water. 1.3 This test method has not been tested with crude oil samples that are solid or waxy, or both, at ambient temperatures. 1.4 The values stated in SI units are to be regarded as standard. Alternate units, in common usage, are also provided to increase clarity and aid the users of this test method. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Methanol in Crude Oils by Multidimensional Gas Chromatography

SN/T 5311-2021 原油及燃油中硫化氢的测定 快速液相萃取法

Rapid liquid phase extraction method for determination of hydrogen sulfide in crude oil and fuel oil

KS M 2069-2021 石油产品沉淀数测试方法

Testing method for precipitation number of petroleum products

ASTM D1401-21 石油和合成流体水分离性的标准试验方法

1.1 This test method covers measurement of the ability of petroleum oils or synthetic fluids to separate from water. Although developed specifically for steam-turbine oils having viscosities of 28.8 mm2 /s to 90 mm2 /s at 40 °C, this test method may be used to test oils of other types having various viscosities and synthetic fluids at other test temperatures. It is recommended, however, that the test temperature be raised to 82 °C 6 1 °C when testing products more viscous than 90 mm2 /s at 40 °C. For higher viscosity oils where there is insufficient mixing of oil and water, Test Method D2711 is recommended. Other test temperatures such as 25 °C may also be used. A 1 % sodium choloride (NaCl) solution or synthetic seawater may be used in place of distilled water when testing certain oils or fuels used in marine applications. 1.2 When testing synthetic fluids whose relative densities are greater than that of water, the procedure is unchanged, but it should be noted that the water will probably float on the emulsion or liquid. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 7. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Water Separability of Petroleum Oils and Synthetic Fluids

NF M07-119-4*NF EN 15199-4:2021 石油产品 用气相色谱法测定沸程分布 第4部分：原油的轻馏分

Petroleum products - Determination of boiling range distribution by gas chromatography method - Part 4: Light fractions of crude oil