77.140.30 承压钢 标准查询与下载

ASTM A859/A859M-04(2019)e1 压力容器部件的年龄 - 硬化合金钢锻件标准规范

1.1 This specification covers requirements for low-carbon age-hardening nickel-copper-chromium-molybdenumcolumbium alloy steel forgings for pressure vessel components. 1.2 Forgings under this specification are available as Grades A or B. Grade A may be ordered in one or two classes as follows: 1.2.1 Grade A Class 1—Normalized-and-precipitation-heattreated, providing a minimum yield strength of 55 ksi [380 MPa] and a minimum tensile strength of 65 ksi [450 MPa]. 1.2.2 Grade A Class 2—Quenched-and-precipitation-heattreated, providing a minimum yield strength of 65 ksi [450 MPa] and a minimum tensile strength of 75 ksi [515 MPa]. 1.2.3 Grade A was the original steel composition in this specification. 1.3 Although the material is readily weldable, welding procedures are of fundamental importance and must be such as not to affect adversely the properties of the material, especially in the heat-affected zone. It is presupposed that welding procedures will be suitable for the material being welded. 1.4 Supplementary requirements, including those applicable in Specification A788/A788M, are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other and values from the two systems shall not be combined. 1.6 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation [SI units], the material shall be furnished to inch-pound units. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Age-Hardening Alloy Steel Forgings for Pressure Vessel Components

ASTM A240/A240M-19 压力容器和一般应用用铬和铬镍不锈钢板、薄板和带材的标准规范

1.1 This specification2 covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications including architectural, building, construction, and aesthetic applications. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

KS D 3560-2018(2023) 锅炉和其他压力容器用碳钢和钼合金钢板

Carbon steel and molybdenum alloy steel plate for boilers and other pressure vessels

KS D 3560-2018 锅炉和其他压力容器用碳钢和钼合金钢板

Carbon steel and molybdenum alloy steel plate for boilers and other pressure vessels

ASTM A723/A723M-18a 高强度压力元件应用合金钢锻件标准规范

1.1 This specification2 covers requirements for highstrength quenched and tempered alloy steel forgings for pressure vessels, isostatic presses, shock tubes, and similar components. 1.2 These materials are not intended for welded construction. 1.3 Three grades of nickel-chromium-molybdenum steels and six classes of increasing tensile strength are included. The strength class, section size, and configuration of the forging will largely dictate the applicable type(s) of steel. 1.4 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as the standard. Within the text and tables, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.5 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inchpound units. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Alloy Steel Forgings for High-Strength Pressure Component Application

ASTM A724/A724M-09(2018) 焊接压力容器用淬火和回火碳锰硅钢压力容器板的标准规范

1.1 This specification2 covers three grades of carbonmanganese-silicon steel, designated Grades A, B, and C. Grade C may be produced with a boron addition. The plates are quenched and tempered and are intended for welded-layered pressure vessels. 1.2 The maximum thickness of plates supplied under this specification is limited only by the capability of the chemical composition to meet the specified mechanical requirements. However, current practice normally limits the maximum thickness to 7⁄8 in. [22 mm] for Grades A and B, and to 2 in. [50 mm] for Grade C. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pressure Vessel Plates, Carbon-Manganese-Silicon Steel, Quenched and Tempered, for Welded Pressure Vessels

BS ISO 4978:2018 焊接气瓶用钢板和钢带

Steel sheet and strip for welded gas cylinders

ISO 4978:2018 焊接气瓶用轧制扁钢制品

This document specifies the characteristics of hot-rolled steel sheet and strip with a thickness up to 12 mm inclusive of the non-alloyed steels listed in Table 1, which are intended for welded gas cylinders in accordance with ISO 4706.

Steel sheet and strip for welded gas cylinders

ASTM A723/A723M-18 高强度压力元件应用合金钢锻件标准规范

Standard Specification for Alloy Steel Forgings for High-Strength Pressure Component Application

KS D 3521-2018(2023) 中温用压力容器用钢板

Steel plates for pressure vessels for intermediate temperature service

KS D 3521-2018(英文版) 中温用压力容器用钢板

Steel plates for pressure vessels for intermediate temperature service

KS D 3533-2018(2023) 气瓶用薄钢板和钢带

Steel sheets, plates and strip for gas cylinders

KS D 3521-2018 中温用压力容器用钢板

Steel plates for pressure vessels for intermediate temperature service

KS D 3540-2018(2023) 中温压力容器用碳钢板

Carbon steel plates for pressure vessels for intermediate and moderate temperature services

KS D 3533-2018 气瓶用钢板和钢带

Steel sheets, plates and strip for gas cylinders

KS D 3540-2018 用于中温和中温服务的压力容器用碳钢板

Carbon steel plates for pressure vessels for intermediate and moderate temperature services

JIS G 3120:2018 压力容器用淬火和回火的锰-钼及锰-钼-镍合金钢板

Manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates quenched and tempered for pressure vessels

ASTM A508/A508M-18 用于压力容器的淬火和回火真空处理的碳钢和合金钢锻件的标准规范

1.1 This specification2 covers quenched and tempered vacuum-treated carbon and alloy steel forgings for pressure vessels such as those used in reactor systems. Specifically, it covers forgings for vessel closures, shells, flanges, tube sheets, rings, heads, and similar parts. 1.2 All grades are considered weldable under proper conditions. Welding technique is of fundamental importance, and it is presupposed that welding procedure and inspection will be in accordance with approved methods for the grade of material used. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inchpound units. NOTE 1—Grades 1 and 1A are composed of different chemistries but have the same mechanical requirements. NOTE 2—Designations have been changed as follows: Current Formerly Grade 1 Class 1 Grade 1A Class 1A Grade 2 Class 1 Class 2 Grade 2 Class 2 Class 2A Grade 3 Class 1 Class 3 Grade 3 Class 2 Class 3A Grade 4N Class 1 Class 4 Grade 4N Class 2 Class 4A Grade 4N Class 3 Class 4B Grade 5 Class 1 Class 5 Grade 5 Class 2 Class 5A Grade 22 Class 3 Class 22B Grade 22 Classes 4, 5, 6, and 7 Grade 3V Class 3V 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Quenched and Tempered Vacuum-Treated Carbon and Alloy Steel Forgings for Pressure Vessels

DIN EN 10207:2018 简单压力容器用钢.钢板、带材和棒材的交货技术条件;德文版本EN 10207-2017

This document specifies the technical delivery requirements for flat products and bars made of steel in accordance with the specifications for pressurized parts in simple pressure vessels as defined in the Directive 2014/29/EU (see Annex A) and standardized in EN 286-1 to -3.

Steels for simple pressure vessels - Technical delivery requirements for plates, strips and bars; German version EN 10207:2017

ASTM A240/A240M-18 压力容器和一般应用用铬和铬镍不锈钢板、薄板和带材的标准规范

1.1 This specification2 covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications including architectural, building, construction, and aesthetic applications. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications