91.060.20 屋顶 标准查询与下载

KS F 4029-2018 压制水泥屋面瓦

Standard specification for pressed cement roof tiles

T/CECS 557-2018 《屋面现浇泡沫混凝土节能防水 一体化系统应用技术规程》

本规程共分为7章，主要内容包括：总则、术语、基本规定、材料、设计、施工和质量验收。

Technical specification for application of integrated energy-saving and waterproof roofing system with cast-in-place foam concrete

ASTM C1491-18 混凝土屋顶摊铺机标准规范

Standard Specification for Concrete Roof Pavers

ASTM E1646-95(2018) 外墙金属屋面板系统通过均匀静压差的水渗透标准试验方法

1.1 This test method covers the determination of the resistance of exterior metal roof panel systems to water penetration when water is applied to the outdoor face simultaneously with a static air pressure at the outdoor face higher than the pressure at the indoor face, that is, positive pressure. This test method is a specialized adaption of Test Method E331. 1.2 This test method is applicable to any roof area and is intended to measure only the water penetration associated with the field of roof including panel side laps and structural connections. It does not include leakage at openings or perimeter or any other details. 1.3 This test method is limited to specimens in which the side seams and attachments are clearly visible and in which the source of leakage is readily determined. Composite systems in which the source cannot be readily determined are outside the scope of this test method. 1.4 The proper use of this test method requires a knowledge of the principles of pressure and flow measurement. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The text of this test method references notes and footnotes excluding tables and figures, which provide explanatory material. These notes and footnotes shall not be considered as requirements of the test method. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 7.1. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Water Penetration of Exterior Metal Roof Panel Systems by Uniform Static Air Pressure Difference

ASTM E196-06(2018) 地板和低坡屋顶的重力荷载试验的标准实施规程

1.1 This practice covers static load testing of floors and low slope roofs (roofs having a slope of less than 1 in 12) under actual or simulated service conditions, and is applicable to typical elements or sections of structures fabricated for test or to actual existing building components. This practice is intended for use in determining the strength and stiffness of elements or sections of floors and roofs of buildings under gravity loads, as well as in checking the design, materials, connections, and the quality of the fabrication of such building constructions. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Gravity Load Testing of Floors and Low Slope Roofs

ASTM D6757/D6757M-18 陡坡屋面用无缝纤维衬垫毡的标准规范

1.1 This specification covers (1) inorganic fiber-reinforced organic felt underlayment and (2) inorganic fiber-based felt for use as underlayment with steep-slope roofing products. The intent of this specification is to provide criteria for producing and evaluating underlayments with a significantly reduced tendency to wrinkle before or after the installation of steep roofing products. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Underlayment Felt Containing Inorganic Fibers Used in Steep-Slope Roofing

T/CCMSA 70101-2018 光伏组件屋面工程技术规程

光伏组件屋面是由光伏组件作为屋顶面层，与支承体系构成的具有光伏发电功能的屋面。 规程对光伏组件屋面工程的设备与材料、结构、性能及要求、安装、检验、运行维护作出了要求。

Technical specification for PV modules roof

DB35/T 1764-2018 沿海地区金属屋面技术条件

本标准规定了福建沿海地区金属屋面系统的术语和定义、订货内容、材料选用、原材料进场质量验收、加工制造、允许偏差、压型金属板检测方法及规则、包装、堆放、运输、标识及质量证明文件、安装要求、检测、维护与维修。 本标准适用于50年一遇的基本风压不小于0.6 kN/m2地区新建、改建和扩建的金属屋面系统。 本标准不适用于采用金属面夹芯板建造的金属屋面系统。

Technical conditions for metal roofs in coastal areas

ASTM D7897-18 模拟自然暴露对太阳反射率和热发射率影响的屋顶材料的实验室污染和风化的标准实施规程

1.1 Practice D7897 applies to simulation of the effects of field exposure on the solar reflectance and thermal emittance of roof surface materials including but not limited to field-applied coatings, factory-applied coatings, single-ply membranes, modified bitumen products, shingles, tiles, and metal products. The solar reflectance and thermal emittance of roof surfacing materials can be changed by exposure to the outdoor environment. These changes are caused by three factors: deposition and retention of airborne pollutants; microbiological growth; and changes in physical or chemical properties. This practice applies to simulation of changes in solar reflectance and thermal emittance induced by deposition and retention of airborne pollutants and, to a limited extent, changes caused by microbiological growth. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Laboratory Soiling and Weathering of Roofing Materials to Simulate Effects of Natural Exposure on Solar Reflectance and Thermal Emittance

BS 5534:2014+A2:2018 用于斜屋顶和垂直覆层的板条和瓷砖 实践守则

What is BS 5534 about?    BS 5534 is a British standard which is the first guidance of its kind in the market   on slating and tiling for roofs and it   sets out good practices in roof slating and tiling.   BS 5534 gives recommendations primarily intended for the design, performance and installation of new build pitched roofs, including vertical cladding, and for normal re-roofing work, including repairs, using slates, tiles, shingles and shakes and their associated components.   Note: The recommendations contained in this BS 5534 might not be appropriate for the re-slating or re-tiling of some old roofs, particularly where traditional and/or reclaimed materials are used. BS 5534 does not cover the structural design of the roof. 

Slating and tiling for pitched roofs and vertical cladding. Code of practice

BS 8612:2018 干燥用于板条和瓷砖的固定屋脊、屋脊和边缘系统 规格

What is this standard about? Currently more than half of the UK’s new and refurbished roofs use dry fixing of ridge and hip systems, yet sometimes there are significant problems with tile security and weather-tightness. This standard supplies clear and practical advice on fixing security, weather-tightness, durability and where required, ventilation. Its aim is to ensure that dry-fix ridge and hip systems are designed and built in such a way that they fulfil the essential requirements of new and refurbished roofs. Who is this standard for? Architects Builders Building control officers Construction assurance companies Roof product designers and manufacturers Roofing contractors Roofing trade associations Why should you use this standard? BS 8612:2018 is the first guidance of its kind in the market. It specifies the performance requirements and methods of test for dry-fixed ridge and hip systems connected to timber ridge/hip battens, ridge boards or hip rafters, and for dry-fixed verge systems installed with slating or tiling. The standard gives minimum performance requirements, including fixing resistance, weather-tightness, durability and also some guidance on ventilation. Performance tests, calculation methods and associated criteria are all included and the standard covers both new buildings and renovations. Use of the standard will: Allow architects, product manufacturers and roofing contractors to communicate precise requirements for fixing and ventilation of roofs and how that can be achieved Provide product designers and manufacturers with minimum performance requirements, calculation methods and test regimes, to ensure that the products fulfil the requirements of the building in which they are installed Simplify the purchasing process ...

Dry fixed ridge, hip, and verge systems for slating and tiling. Specification

ASTM A755/A755M-18 室外暴露建筑产品用热浸镀和卷涂预涂金属薄板的标准规范

1.1 This specification covers steel sheet metallic coated by the hot-dip process and coil-coated with organic films for exterior exposed building products. Sheet of this designation is furnished in coils, cut lengths, and formed cut lengths. Building products include corrugated and various types of roll and brake-formed configurations. 1.2 The substrate is available in several different metalliccoated steel sheet products as enumerated in 4.1, depending on the requirements of the purchaser. 1.3 Coating systems supplied under this specification consist of a primer coat covered by various types and thicknesses of top coats. The combination of primer and top coat is classed as either a two-coat thin-film system or as a two-coat (or more) thick-film system. Typical top-coating materials are: polyester, silicone polyester, acrylic, fluoropolymer, plastisol, or polyurethane. 1.4 This specification is applicable to orders in either inch-pound units (as A755) or SI units [as A755M]. Values in inch-pound units and SI units are not necessarily equivalent. Within the text, SI units are shown in brackets. Each system shall be used independently of each other. 1.5 Unless the order specifies the “M” designation (SI units), the product shall be furnished to inch-pound units. 1.6 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this specification. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building Products

DB11/T 1508-2017 非固化橡胶沥青防水涂料施工技术规程

Technical specification for construction of non-curing rubber asphalt waterproof coating

ASTM F2021-17 塑料虹吸屋顶排水系统设计和安装的标准指南

Standard Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems

KS F 4522-2017 屋顶排水沟

Roof drains

KS F 4522-2017(2022) 屋顶排水沟

Roof drains

ASTM E1514-98(2017)e1 结构立柱钢屋顶板系统标准规范

1.1 This specification covers the design, construction, and weatherability of structural standing seam steel roof panel systems. It includes performance requirements for the following elements only: panels, concealed panel clips, panel/clip anchorage, and panel joint sealers. NOTE 1—These systems are used on both low-slope and steep-slope roof applications. They also are used with or without an underlying deck or sheathing. 1.2 The objective of this specification is to provide for the overall performance of the structural standing seam steel roof panel system as defined in 3.2.6 during its service life in order to provide weather protection, carry the specified design loads, and allow proper access over the roof surface in order to provide for periodic maintenance of equipment by the owner. 1.3 In addition to structural, the specifier shall evaluate other characteristics beyond the scope of this specification that affect the final choice of roof construction. These include, but are not limited to, functional, legal, insurance, and economic considerations. See Appendix X1 for specifier’s checklist. 1.4 The specification is not intended to exclude products or systems not covered by the referenced documents. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The text of this specification contains notes and footnotes that provide explanatory information and are not requirements of this specification. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Structural Standing Seam Steel Roof Panel Systems

ASTM E1592-05(2017) 通过均匀静压气压差对钣金屋面和侧板系统进行结构性能的标准试验方法

1.1 This test method covers the evaluation of the structural performance of sheet metal panels and anchor-to-panel attachments for roof or siding systems under uniform static air pressure differences using a test chamber or support surface. 1.2 The provisions of this test method are applicable to standing seam, trapezoidal, ribbed, or corrugated metal panels in the range of thickness from 0.012 to 0.050-in. (0.3 to 1.3-mm) and apply to the evaluation of uniform pressure applied to single-skin construction or one sheet metal layer of multiple-skin construction. They do not cover requirements for the construction of a specimen to determine the load sharing that can occur with either composite or multiple-layer construction such as: (1) metal cladding over wood sheathing; or (2) field assemblies of insulation sandwiched between corrugated or formed metal panels. 1.3 Proper use of this test method requires knowledge of the principles of pressure and deflection measurement. 1.4 This test method describes optional apparatus and procedures for use in evaluating the structural performance of a given system for a range of support spacings or for confirming the structural performance of a specific installation. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The text of this standard references notes and footnotes exclusive of those for tables and figures. These notes and footnotes provide explanatory material and shall not be considered as requirements of the standard. 1 This test method is under the jurisdiction of ASTM Committee E06 on Performance of Buildings and is the direct responsibility of Subcommittee E06.57 on Performance of Metal Roof Systems. Current edition approved Oct. 1, 2017. Published October 2017. Originally approved in 1995. Last previous edition approved in 2012 as E1592 – 05(2012). DOI: 10.1520/E1592-05R17. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 7. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference

ASTM E2140-01(2017) 通过静态水压头对金属屋面板系统进行渗水的标准试验方法

1.1 This laboratory test method covers the determination of the resistance to water penetration of exterior metal roof panel system sideseams, endlaps, and roof plane penetrations when a specified static water pressure head is applied to the outside face of the roof panel. NOTE 1—This test method is intended to evaluate water-barrier (not water-shedding) roof system joints and details. These systems are also referred to as hydrostatic roof systems. 1.2 This test method is limited to specimens in which the sideseams and attachments are clearly visible and in which the source of leakage is readily observable. 1.3 This test method excludes performance at roof perimeter conditions. 1.4 This test method is suitable for evaluating leakage at roof plane penetrations such as fasteners, curbs, pipes, and expansion joints under a static water pressure head. 1.5 The proper use of this test method requires a knowledge of the principles of water pressure. 1.6 The text of this standard includes notes and footnotes excluding tables and figures, which provide explanatory material. These notes and footnotes shall not be considered as requirements of the standard. 1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 7. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Water Penetration of Metal Roof Panel Systems by Static Water Pressure Head

ASTM D7851-17 可持续 低斜率屋顶系统设计标准指南

1.1 This guide provides guidance and considerations related to designing sustainable low-sloped roofing systems, including exposed membrane roofs, membranes covered with vegetative (green) overburden systems, ballasted roofs, and protected membrane roofing assemblies. A sustainable roofing system minimizes environmental impact, conserves energy, and has maximized service life. 1.2 The primary purpose of a roofing system is to weatherproof the building’s top surface. Implementing a sustainable roofing system is the intent of this guide. 1.3 This guide acknowledges that many factors outside the designer’s control affect the longevity of a roofing system. The designer may rely on industry literature (X1.1) and personal experience with roofing systems to estimate the design life. 1.4 The premise of this guide is to focus attention on environmental and other factors that may affect the roofing system over its service life. By considering these factors and incorporating into the roofing system design certain features that mitigate these factors and their potential adverse effects on the roofing system, the roofing system would be expected to have a longer service life. 1.5 This guide includes materials used in roofing systems under jurisdiction of ASTM Committee D08 on Roofing and Waterproofing. The applicability of this guide to other systems and materials has not been determined. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Design of Sustainable, Low-Slope Roofing Systems