91.060.20 屋顶 标准查询与下载

ASTM D6225/D6225M-98(2020) 矿物表层屋面颗粒盖标准试验方法

1.1 This test method covers the determination of the hiding power of granules on a mineral-surfaced roofing sheet. The test is used primarily after an abrasion test has been conducted to determine the portion of asphaltic compound that has been exposed as a result of the abrasion test. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Granule Cover of Mineral-Surfaced Roofing

T/CECS 672-2020 浮筑楼板隔声保温系统应用技术规程

主要技术内容包括：总则、术语、系统及组成材料、设计、施工、质量验收。

Technical specification for application of sound & thermal insulation system of floating floor

ASTM E2777-20 植物标准指南

1.1 This guide identifies terminology, principles, and fundamental concepts including those related to sustainability, technical requirements of construction, and types of vegetative (green) roof systems used on buildings. 1.2 The considerations for sustainable development relative to vegetative (green) roof systems are categorized as follows: environmental, social, and economic as consistent with Guide E2432. (See Appendix X1.) 1.3 This guide discusses technical requirements for vegetative (green) roof systems pertaining to the following categories: plants, media, wind scour resistance, soil reinforcement, separation or filter layers, drain layers, water retention layers, protection layers, and root penetration barriers. 1.4 This guide addresses intensive and extensive vegetative (green) roof systems for roofs up to 15 % slope. Roofing/ waterproofing membranes and insulation are key components of vegetative (green) roof systems, but technical requirements regarding their role in such roof systems is beyond the scope of this guide. NOTE 1—ASTM Technical Committees D08 and C16 have jurisdiction over the development of standards for roofing/waterproofing membranes and insulations, respectively. Some of their existing standards may be helpful in the evaluation of membranes and insulation used in vegetative (green) roof systems. As these two committees develop standards for such roofs, this guide will be revised appropriately. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Vegetative (Green) Roof Systems

KS F 4729-2019 屋顶用预制混凝土板的标准规范

Standard specification for precast concrete panel for roof

KS F 4751-2019 压盖石材涂层金属屋顶瓦的标准规范

Standard specification for glanule stone coated metal roofing tile

ASTM C1491-19 混凝土屋顶摊铺机标准规范

1.1 This specification covers concrete roof pavers that are machine-made from hydraulic cement, water, and suitable mineral aggregates with or without the inclusion of other materials, for use as roof ballast and protection of roof membranes. NOTE 1—The design of roof ballast systems for resisting wind uplift is beyond the scope of this specification. Building codes and other standards should be consulted in designing for wind uplift resistance. 1.2 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Concrete Roof Pavers

ASTM D7158/D7158M-19ae1 沥青瓦抗风性的标准试验方法（抗拔力/抗拔力法）

Standard Test Method for Wind Resistance of Asphalt Shingles (Uplift Force/Uplift Resistance Method)

ASTM D7158/D7158M-19a 沥青瓦抗风性的标准试验方法（抗拔力/抗拔力法）

Standard Test Method for Wind Resistance of Asphalt Shingles (Uplift Force/Uplift Resistance Method)

BS EN 508-2:2019 金属板屋顶和覆层产品 钢、铝或不锈钢板自承式产品规范 铝

What is BS EN 508 ‑ 2 – Roofing and cladding products from metal sheets about? BS EN 508 ‑ 2 is the second part of the EN 508 multi-series that discusses roofing and cladding products from metal sheets. BS EN 508 ‑ 2 specifies requirements for self-supporting external profiled sheets for the roof covering, wall cladding, lining and liner tray products for discontinuous laying made from aluminium sheets with or without surface treatment (additional organic coatings or anodising). BS EN 508 ‑ 2 applies to all discontinuously laid self-supporting external profiled sheets for the roof covering, wall cladding, lining and liner trays with the exception of tiles with a surface area less than 1 m2 and produced by stamping. These profiled roof sheets are designed to keep wind, rain and snow out of the building, and to transfer any resultant loads and infrequent maintenance loads to the structure. BS EN 508 ‑ 2 does not cover products for structural purposes, i.e., it does cover products used in s...

Roofing and cladding products from metal sheet. Specification for self-supporting products of steel, aluminium or stainless steel sheet. Aluminium

T/CECS 617-2019 村镇建筑屋面工程技术规程

本规程共分为7章，主要技术内容包括：总则、术语、基本规定、材料要求、设计、施工、质量验收。

Technical specification for roof engineering of rural building

EN 508-2:2019 金属薄板屋面材料产品.钢,铝或不锈钢薄板材制自支撑产品.第2部分:铝

This part of EN 508 specifies requirements for self-supporting external profiled sheets for roof covering, wall cladding, lining and liner tray products for discontinuous laying made from aluminium sheet with or without surface treatment (additional organic coatings or anodising). This document establishes general characteristics, definitions, classifications and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are made available on the market before being despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions. This document applies to all discontinuously laid self-supporting external profiled sheets for roof covering, wall cladding, lining and liner trays with the exception of tiles with a surface area less than 1 m2 and produced by stamping. These profiled roof sheets are designed to keep wind, rain and snow out of the building, and to transfer any resultant loads and infrequent maintenance loads to the structure. This document does not cover products for structural purposes, i.e. it does cover products used in structural class III (according to EN 1999-1-4), it does not cover products used in constructions of Structural Classes I and II (according to EN 1999-1-4) intended to contribute to the global or partial stability of the building structure by providing racking resistance or resistance of permanent static loads (excluding self-weight of the metal sheet). No requirements for supporting construction, design of roof system and execution of connections and flashings are included.

Roofing and cladding products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet - Part 2: Aluminium

ASTM D4977/D4977M-03(2019) 通过磨损对矿物表层屋顶的颗粒附着力的标准测试方法

Standard Test Method for Granule Adhesion to Mineral Surfaced Roofing by Abrasion

ASTM E455-19 建筑物用框架地板或屋顶隔板结构的静载荷试验的标准试验方法

1.1 This test method covers procedures designed (1) to evaluate the static shear capacity of a typical segment of a framed diaphragm under simulated loading conditions, and (2) to provide a determination of the stiffness of the construction and its connections. A diaphragm construction is an assembly of materials designed to transmit shear forces in the plane of the construction. 1.2 No effort has been made to specify the test apparatus, as there are a number that can be used as long as the needs of the testing agency are met. If round-robin testing is to be conducted, test apparatus and testing procedures shall be mutually agreed upon in advance by the participants. 1.3 The text of this standard contains notes and footnotes that provide explanatory information and are not requirements of the standard. Notes and footnotes in tables and figures are requirements of this standard. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 6. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Static Load Testing of Framed Floor or Roof Diaphragm Constructions for Buildings

JIS A 6602:2019 住宅阳台用屋顶构件

Roof components for terrace of dwellings

ASTM E2399/E2399M-19 植物（绿色）屋顶系统的负荷分析最大介质密度的标准测试方法

1.1 This test method covers a procedure for determining the maximum media density for purposes of estimating the maximum dead load for green roof assemblies. The method also provides a measure of the moisture content, the air-filled porosity, and the water permeability measured at the maximum media density. 1.2 This procedure is suitable for green roof media that contain no more than 30 % organic material as measured using the loss on ignition, as described in Test Methods E177, Test Method C. The test specimen should be a bulk oven-dried sample prepared according to Test Methods E177, Test Method A. 1.3 The maximum media density and associated moisture content measured in this procedure applies to drained conditions near the saturation point. 1.4 The test method is intended to emulate vertical percolation rates for water in green roofs. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and to determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Maximum Media Density for Dead Load Analysis of Vegetative (Green) Roof Systems

ASTM D7158/D7158M-19 沥青瓦抗风性的标准试验方法（抗拔力/抗拔力法）

Standard Test Method for Wind Resistance of Asphalt Shingles (Uplift Force/Uplift Resistance Method)

ASTM D2523/D2523M-13(2019)e1 屋顶膜荷载应变特性试验的标准实施规程

1.1 This practice is a guide for determining the load-strain properties of roofing membranes and their components at various temperatures. Test specimens may be prepared in the laboratory or cut from samples obtained in the field. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Testing Load-Strain Properties of Roofing Membranes

T/CCMSA 60103-2018 脚手架用S600E高强不锈结构钢焊接钢管

本标准规定了脚手架用S600E高强不锈结构钢焊接钢管的术语和定义、规格和标记、要求、试验方法、检验规则，以及标志、包装、运输和贮存等。适用于建设工程脚手架、支撑架用S600E高强不锈结构钢焊接钢管。  主要技术内容包括对S600E高强不锈结构钢焊接钢管的规格、标记、允许偏差、外观品质、质量、化学成分、物理和力学性能、常规试验以及金相组织等提出了要求。 在试验方法中对规格和允许偏差、外观品质、质量、化学成分、物理性能、常规试验和金相组织做出了规定。 标准对检验规则、标志、包装、运输与贮存做出了明确要求。

S600E High strength stainless structural steel welded steel pipe for scaffolding

KS F 4029-2018 压制水泥屋面瓦

Standard specification for pressed cement roof tiles

KS F 4029-2018(2023) 压制水泥屋面砖的标准规范

Standard specification for pressed cement roof tiles